6Specifications

Lopi Yankee Bay Pellet Insert manual 6Specifications

Page 6

Heating Specifications:

Approximate Maximum Heating Capacity (in square feet)*	800 to 2,250
Burn Rate (Pounds per Hour)**	1.7 to 5.5
Maximum Burn Time on Low Burn**	28 to 52 Hours
Hopper Capacity (based upon hopper extension position)	48 to 89 Pounds

*Heating capacity will vary depending on the home's floor plan, degree of insulation, and the outside temperature. It is also affected by the fuel size, quality, and moisture level.

**Small pellets will increase or decrease the stated burn rates and burn times. Differences of plus or minus 20% depending on fuel quality may occur.

Dimensions:

Center of 4” diameter Flue is 16-7/8” above the baseplate and 7-1/2” left of center

32”

26-1/2”

25-1/2” (allow 36” width for control board installation)

	25-3/4” to 20”
	See “Hopper Extension Set-up”
	for details.
45”	13-1/4” (allow 14” depth in the Fireplace)
	13-1/4” (allow 14” depth in the Fireplace)
12"	Fireplace Opening
	Door Opening
Electrical Specifications:
Electrical Rating	115 Volts, 3.6 Amps, 60 Hz
Watts During Start-Up Sequence	400 (approximately)
Watts During Operation	180 (approximately)

Fuel:

The unit is designed for wood pellets that comply with the standards set by the Association of Pellet Fuel Industry (density of at least 40 lbs. per cubic foot, 1/4" to 5/16" diameter, length no greater than 1–1/2", 8200 BTU's/lb., moisture under 8% by weight, ash under 1% by weight, and salt under 300 parts per million). If the fuel does not comply to this standard, the unit may not operate as designed.

N O T E: This heater may use alternative fuel if equipped with the multi-fuel fire pot and properly maintained. See the publication “Multi-Fuel Pellet Fire Pot” for requirements (available from your Travis Industries, Inc. dealer).

EPA Compliance:

This heater is EPA exempt from Phase II requirements, but has been tested for emissions using EPA test methods by OMNI Test Labs.

Travis Industries

4 0 5 0 5 0 9

1 0 0 - 0 1 1 4 5

Image 6

Contents

Yankee Bay Pellet Insert 2Introduction Introduction Important Information Travis Industries 5 0 5 0 0 0 1 1 4 Table of Contents 4Safety Precautions Safety Precautions Mobile Home6Specifications Installation7 8Installation Hopper Extension Set-upInstallation9 Re-install the hopper walls following the directions below0Installation Installation1 Venting the Pellet Stove2Installation Mobile Home RequirementsOutside Air used for combustion Not Enough Air Baffle InstallationRestrictor Adjustment Too Much Air4Installation Surround Panel & Circuit Board InstallationInstallation into a Masonry Fireplace Hint6Installation Installation into a Factory Built MetalLocation of Controls Safety NoticeOperation1 Starting the Heater for the First Time8Operation Loading PelletsTwo Modes of Operation To Start Manual ModeTo Adjust the Heat To Shut DownAuto Mode To Adjust Room Temperature or Start the Stove0Operation Adjusting the Fan Speed Operation22Operation Inspect the Burn Maintenance2Daily Maintenance whenever using the heater Make Sure Pellets are Not Piling Up4Maintenance Cleaning the FirepotCheck Firepot for Clinkers Cleaning the Optional Plated Surfaces Bi-Weekly Maintenance or every 10 bags of pelletsClean the Heat Exchange Tubes Vacuum Hopper6Maintenance Opening The DoorClean the Glass Check Baffles, Ashbox, Ashpan, Dispose Ash If Necessary8Maintenance Sweep Ash Into AshpanYearly Maintenance or every two tons 0Maintenance Clean the Vent make sure the heater and vent is coolMaintenance3 Door SealDoor Alignment 2Maintenance Adjusting the Door Hinge and LatchReplacement Parts Check for Air Leaks Around the Door, Glass, and Ashpan4Normal Operating Sounds Safety Label Serial NoLimited 7 Year Warranty Years 1 & 2 Coverage Parts & LaborOptional Equipment Thermostat8Optional Equipment Remote ThermostatOptional Log ZC Kit 9 9 2 0 0 1 4 0Index

Lopi Yankee Bay Pellet Insert manual 6Specifications