Pentax N-0751M-OD installation manual Vent Piping, Clearances, Appliance Adapters

Page 13
Part No.
FSAA4
9401RYPK
2SVWA04
SRASPSA4

8. Vent Pipe Installation (Indoor Installation Only)

[ For N-0751M]

WARNING

CARBON MONOXIDE POISONING

Follow all vent system requirements in accordance with relevant local or state regulation, or, in the absence of local or state code, in the U.S. to the National Fuel Gas Code ANSI

Be sure to do

Z233.1/NFPA 54 – latest edition, and in Canada, in accordance with NSCNGPI.

 

Vent Piping

Use only UL listed category III vent materials.

Follow the vent pipe manufacturer's installation instructions.

Pipe diameter

100mm (4")

 

 

No. of Elbows

Max. Straight Vent Length

3

4.6m (15')

2

8.2m (27')

1

11.7m (39')

Make the vertical section of the exhaust vent as short as possible.

Maintain the same vent pipe diameter from the heater flue to the vent termination.

Clearances

Manufacturer and

Enclosed

Unenclosed

 

 

 

 

 

 

Product

Hor.

Vert.

Hor.

Vert.

Noritz N-Vent

250mm (10") (sides)

100mm

75mm

75mm

150mm (6") (bottom)

(4")

(3")

(3")

 

 

375mm (15") (top)

 

 

 

 

Protech FasNSeal

200mm (8") (sides)

100mm

75mm

75mm

100mm (4") (bottom)

(4")

(3")

(3")

 

 

300mm (12") (top)

 

 

 

 

Protech FasNSeal W2

150mm

100mm

75mm

75mm

 

(6")

(4")

(3")

(3")

 

HeatFab SafTVent

150mm

150mm

50mm

50mm

(6")

(6")

(2")

(2")

 

Z-Flex Z-Vent

200mm

100mm

25mm

25mm

(8")

(4")

(1")

(1")

 

Flex-L-StaR-34

200mm

100mm

25mm

25mm

(8")

(4")

(1")

(1")

 

These clearances are subject to change.

Refer to the UL listing for the proper clearances.

The first vertical run from the top of the heater should be no longer than 0.9m (3').

Make sure vent pipe is gas tight and will not leak. Use silicon sealant wherever necessary.

Do not common vent or connect more than one appliance to this venting system.

The total vent length including horizontal & verti- cal vent runs should be no less than 0.9m (3').

Do not place any dangerous objects at the end of the exhaust vent and check that vent pipe is not blocked in any way.

Steam (smoke) or water drops may come out from the end of the exhaust pipe. Select the location for the end of the vent so that steam is not visible, and the vent is not wet with drip- ping water.

If snow is expected to accumulate, take care the end of the pipe is not covered with snow or hit by falling lumps of snow.

Consult the vent pipe manufacturer's install- ation instructions for chimney connections.

Appliance Adapters

Use the following adapters to connect the unit to the venting system.

Manufacturer and

Product

Protech FasNSeal

HeatFab SafTVent

Z-Flex Z-Vent

Flex-L Star-34

13

Image 13
Contents Canada Installation ManualPart Shape Remote Controller Outdoor Junction BoxEach See p Part Shape Outdoor Vent Cap VC4-1Typical Plumbing System DiagramController to only one UnitsBefore Installation With corrugated Choosing Installation SiteProhibited Be sure to do Min 75mm 200mm Or Min 75mm 3 more Installation Clearances600mm 24 or more Such as the wall of the second floor where the unit is out When installing the unit on a balcony, etc., secure anMaintain the following clearance from both combustible Non-combustible materialsVent Terminal Window, or gravity air inlet into any building 9m 3 above any forced air inlet withinFor N-0751M- OD Be damaged and may become highly dangerous InstallationLocating Screw Holes Mounting Clearances Vent PipingAppliance Adapters Vertical Vent Termination Horizontal Vent TerminationOpenings supplying indoor air Combustion AirGas Pressure Gas PipingMeasuring Gas Pressure Gas Meter Gas ConnectionGas Line Sizing for a Noritz Gas Water Heater Drain piping Supply water pipingHot water piping For Space Heating Purposes Plumbing ApplicationsBreaker Installation Electrical WiringGround Remove the front cover of the water heater 4 screws Remote ControllerHeard 2 sec. and 50 C 122 F appears on the display Remote controller cord Connecting Remote Controller Cord to UnitWire Tag Connecting the pump control wireRelay connection with larger pumps 85 W Pump ControlConnecting the Quick Connect Cord to the two units Remote controller can be connected to eitherWiring Throughway Coupling Cord Unit a or BPeriodically check the following to ensure proper MaintenanceOperation of the water heater Lighting Instructions Handling after trial operationShutdown Instructions 0751M Dimensions0751M-OD Included Parts List For InstallersConnection of Remote Controller Cord White ConnectorRemote Controller Cord Rear Side InstallationTie the redundant length of the remote Box NutController cord outside the junction box Close the junction boxPas évitée, entraînera des blessures graves ou mortelles Natural Gas and Propane Installation Code NscngpicProduits Voir p.21 Ce document Cordon de Télécommande Commencer l’installation Pièce FormeÊtre nécessaires à l’installation Pièce Forme Boîte de dérivation Extérieure de la TélécommandeSchéma du système Télécommande à Un seul des AppareilsPlomberie type Remarque Raccordez laCheck-up Avant l’installationVérifiez le gaz Vérifiez la qualité de l’alimentation en eauChoix du site d’installation Interdit Veillez à ’exécuter Dégagement pour linstallation Lorsque vous installez lunité sur un balcon, etc., laissez Indique la distance lors de linstallation dune plaqueDe calorifugeage matière incombustible autre que le Métal, dune épaisseur de 2.5mm 0.1 ou plus ouEntrée d’alimentati on en air Rapport aux ouvertures d’un bâtiment Maintenez les dégagements suivants par2m 4 dessous, 1.2m Horizontalement à partir de, ou 0.3mEncastr 3m 1 dessous, 0.3m Installation dun boîtier encastré avecCache déposé Fixation au mur Tuyauterie de l’évent Installation du tuyau d’évent uniquementDégagement Adaptateurs d’appareilBouche de l’évent vertical Bouche de l’évent horizontalOuvertures alimentant en air intérieur Air comburantMesure de la pression du gaz Compteur à gaz Pression du gazRaccordement de gaz Adapté de UC1997 Conduite d’eau Pour le chauffage du bâtiment PlomberieInstallation du disjoncteur Qualifié pour l’installation électriqueAdressez-vous à un électricien TerreCoupez lalimentation électrique du chauffe-eau TélécommandeCordon de télécommande Raccordement du cordon de télécommande à l’unitéAttache Câble 18AWG Connexion par relais avec de grandes pompes 85W Raccordement du câble de commande de la pompeConnecteur Attache Ouverture pour Cordon de Câbles Couplage Branchement du cordon de raccordement rapide aux deux unitésGarantir un bon fonctionnement du chauffe-eau Vérifiez régulièrement les points suivants pourInstructions d’allumage Manipulation après le test de fonctionnementInstructions d’arrêt 10mm Remarques sur l’emplacement d’installation Pour les installateursNom des pièces Quantité Télécommande Garniture du mur RemarqueInstallation Écrou de Attachez le cordon de la télécommandeLa boîte Qui dépasse à l’extérieur de la boîte de

N-0751M-OD, N-0751M specifications

The Pentax N-0751M and N-0751M-OD are advanced digital cameras designed primarily for outdoor and rugged environments. These models exemplify the blend of functionality and durability that Pentax is known for, appealing to both photography enthusiasts and professionals who require reliable equipment in demanding conditions.

One of the standout features of the N-0751M and its counterpart, the N-0751M-OD, is their robust construction. Built to withstand harsh environments, these cameras are weather-resistant, ensuring that they can handle rain, dust, and extreme temperatures. This makes them ideal for nature photographers, adventure enthusiasts, and even those who work in challenging conditions.

The N-0751M series is equipped with a high-resolution sensor that captures stunning images with remarkable clarity and detail. The camera features an advanced image processing engine that enhances color accuracy and dynamic range, allowing users to create vibrant and lifelike photos. This sensor also performs exceptionally well in low-light environments, making it versatile for various shooting situations.

Another key characteristic of the N-0751M and N-0751M-OD is their fast and responsive autofocus system. This ensures that users can quickly lock onto their subjects, which is critical for capturing fleeting moments, whether in wildlife photography or action sports. The cameras also come with multiple autofocus modes and options, providing photographers with the flexibility to choose the best setting for their shooting style.

In terms of usability, the N-0751M series features an intuitive interface with customizable settings that allow users to adapt the camera to their personal preferences. The ergonomic design promotes comfort during extended shooting sessions, making it easy to navigate through menus and settings quickly.

For connectivity, the N-0751M and N-0751M-OD come equipped with Wi-Fi capabilities, facilitating easy sharing and remote control through a smartphone app. This enables photographers to transfer images wirelessly and control the camera from a distance, enhancing the shooting experience.

In summary, the Pentax N-0751M and N-0751M-OD embody the perfect combination of durability, image quality, and user-friendly technology. With robust features that cater to professional demands, these cameras stand out as reliable tools for capturing stunning images in any environment. Whether for work or passion, photographers can count on the N-0751M series to deliver superior performance and exceptional results.