Pentax N-0751M-OD Remote Controller, Remove the front cover of the water heater 4 screws

Page 21

Remote Controller

• Applicable Model

N-0751M,OD

Remote controller

RC-7650M

Install the remote controller according to the instructions in the Installation Guide (p. 28).

*The water heater has been factory set to allow a maximum temperature setting of 50°C (122°F). To access higher temperature settings through the remote controller, follow the below steps.

<When setting the maximum temperature to 55-60°C (130-140°F)>

1.Turn the water heater off by pressing the ON/OFF button on the remote controller.

2.Press and hold the FLOW METER ALARM SET button until a sound is heard (2 sec.) and 50°C (122°F) appears on the display.

3.Set the upper limit of the hot-water supply temperature to 55°C(130°F) or 60°C (140°F) using the UP and DOWN setting buttons.

4.To put the water heater back into operation, press the ON/OFF button on the remote controller. To keep the water heater off, let the unit sit for 30 sec. to return to the original display.

<When setting the maximum temperature to 55-83°C (130-180°F)>

 

1.

Turn the water heater off by pressing the ON/OFF button on the remote

 

 

controller.

 

2.

Disconnect electrical power to the water heater.

TOR

NNEC

CO

TEMPERATURE

3.

Remove the front cover of the water heater (4 screws).

STMENT

TER

ADJU

WA

 

4. Connect "WATER TEMPERATURE ADJUSTMENT CONNECTOR" tag

 

 

connector to "180°F" tag connector as shown on the right.

 

5.

Replace the front cover of the water heater (4 screws).

 

6. Reconnect electrical power to the water heater, but do not turn it on.

 

7.

Press and hold the FLOW METER ALARM SET button until a sound is (the back : 55 C) (the back : 60 C)

WATER TEMPERATURE

ADJUSTMENT CONNECTOR

heard (2 sec.) and 50°C (122°F) appears on the display.

(the back : 83 C)

 

8.Set the upper limit of the hot-water supply temperature to

55°C (130°F), 60°C, 65°C, 70°C, 75°C (140°F, 149°F, 158°F, 167°F) or 83°C (180°F) using the UP and DOWN setting buttons.

9.To put the water heater back into operation, press the ON/OFF button on the remote controller. To keep the water heater off, let the unit sit for 30 sec. to return to the original display.

•The N-0751M, OD can be programmed so that it will default to one of four temperatures if the remote controller is removed (80°C, 60°C, 55°C, 50°C (176°F, 140°F, 130°F, 122°F)). To change the default

temperature, connect the temperature selection wire as shown in the above diagram. The default tem- perature is 50°C (122°F) when the temperature selection wire is not connected.

WARNING

•When changing the temperature, make sure to confirm with the customer that the temperature of the hot water will be very high and that there is a risk of scalding.

•Water temperatures above 52°C (125°F) can cause severe burns or death from scalding.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Canada Installation ManualPart Shape Remote Controller Outdoor Junction BoxEach See p Part Shape Outdoor Vent Cap VC4-1Typical Plumbing System DiagramController to only one UnitsBefore Installation With corrugated Choosing Installation SiteProhibited Be sure to do Installation Clearances Min 75mm 200mm Or Min 75mm 3 more600mm 24 or more Such as the wall of the second floor where the unit is out When installing the unit on a balcony, etc., secure anMaintain the following clearance from both combustible Non-combustible materialsVent Terminal Window, or gravity air inlet into any building 9m 3 above any forced air inlet withinFor N-0751M- OD Installation Be damaged and may become highly dangerousLocating Screw Holes Mounting Vent Piping ClearancesAppliance Adapters Vertical Vent Termination Horizontal Vent TerminationOpenings supplying indoor air Combustion AirGas Pressure Gas PipingMeasuring Gas Pressure Gas Meter Gas ConnectionGas Line Sizing for a Noritz Gas Water Heater Supply water piping Drain pipingHot water piping For Space Heating Purposes Plumbing ApplicationsElectrical Wiring Breaker InstallationGround Remote Controller Remove the front cover of the water heater 4 screwsHeard 2 sec. and 50 C 122 F appears on the display Remote controller cord Connecting Remote Controller Cord to UnitWire Tag Connecting the pump control wireRelay connection with larger pumps 85 W Pump ControlConnecting the Quick Connect Cord to the two units Remote controller can be connected to eitherWiring Throughway Coupling Cord Unit a or BMaintenance Periodically check the following to ensure properOperation of the water heater Handling after trial operation Lighting InstructionsShutdown Instructions Dimensions 0751M0751M-OD Included Parts List For InstallersConnection of Remote Controller Cord White ConnectorRemote Controller Cord Rear Side InstallationTie the redundant length of the remote Box NutController cord outside the junction box Close the junction boxNatural Gas and Propane Installation Code Nscngpic Pas évitée, entraînera des blessures graves ou mortellesProduits Voir p.21 Ce document Cordon de Télécommande Commencer l’installation Pièce FormeÊtre nécessaires à l’installation Pièce Forme Boîte de dérivation Extérieure de la TélécommandeSchéma du système Télécommande à Un seul des AppareilsPlomberie type Remarque Raccordez laCheck-up Avant l’installationVérifiez le gaz Vérifiez la qualité de l’alimentation en eauChoix du site d’installation Interdit Veillez à ’exécuter Dégagement pour linstallation Lorsque vous installez lunité sur un balcon, etc., laissez Indique la distance lors de linstallation dune plaqueDe calorifugeage matière incombustible autre que le Métal, dune épaisseur de 2.5mm 0.1 ou plus ouEntrée d’alimentati on en air Rapport aux ouvertures d’un bâtiment Maintenez les dégagements suivants par2m 4 dessous, 1.2m Horizontalement à partir de, ou 0.3mInstallation dun boîtier encastré avec Encastr 3m 1 dessous, 0.3mCache déposé Fixation au mur Tuyauterie de l’évent Installation du tuyau d’évent uniquementDégagement Adaptateurs d’appareilBouche de l’évent vertical Bouche de l’évent horizontalOuvertures alimentant en air intérieur Air comburantPression du gaz Mesure de la pression du gaz Compteur à gazRaccordement de gaz Adapté de UC1997 Conduite d’eau Pour le chauffage du bâtiment PlomberieInstallation du disjoncteur Qualifié pour l’installation électriqueAdressez-vous à un électricien TerreCoupez lalimentation électrique du chauffe-eau TélécommandeRaccordement du cordon de télécommande à l’unité Cordon de télécommandeAttache Câble 18AWG Connexion par relais avec de grandes pompes 85W Raccordement du câble de commande de la pompeConnecteur Attache Ouverture pour Cordon de Câbles Couplage Branchement du cordon de raccordement rapide aux deux unitésGarantir un bon fonctionnement du chauffe-eau Vérifiez régulièrement les points suivants pourManipulation après le test de fonctionnement Instructions d’allumageInstructions d’arrêt 10mm Remarques sur l’emplacement d’installation Pour les installateursNom des pièces Quantité Télécommande Garniture du mur RemarqueInstallation Écrou de Attachez le cordon de la télécommandeLa boîte Qui dépasse à l’extérieur de la boîte de

N-0751M-OD, N-0751M specifications

The Pentax N-0751M and N-0751M-OD are advanced digital cameras designed primarily for outdoor and rugged environments. These models exemplify the blend of functionality and durability that Pentax is known for, appealing to both photography enthusiasts and professionals who require reliable equipment in demanding conditions.

One of the standout features of the N-0751M and its counterpart, the N-0751M-OD, is their robust construction. Built to withstand harsh environments, these cameras are weather-resistant, ensuring that they can handle rain, dust, and extreme temperatures. This makes them ideal for nature photographers, adventure enthusiasts, and even those who work in challenging conditions.

The N-0751M series is equipped with a high-resolution sensor that captures stunning images with remarkable clarity and detail. The camera features an advanced image processing engine that enhances color accuracy and dynamic range, allowing users to create vibrant and lifelike photos. This sensor also performs exceptionally well in low-light environments, making it versatile for various shooting situations.

Another key characteristic of the N-0751M and N-0751M-OD is their fast and responsive autofocus system. This ensures that users can quickly lock onto their subjects, which is critical for capturing fleeting moments, whether in wildlife photography or action sports. The cameras also come with multiple autofocus modes and options, providing photographers with the flexibility to choose the best setting for their shooting style.

In terms of usability, the N-0751M series features an intuitive interface with customizable settings that allow users to adapt the camera to their personal preferences. The ergonomic design promotes comfort during extended shooting sessions, making it easy to navigate through menus and settings quickly.

For connectivity, the N-0751M and N-0751M-OD come equipped with Wi-Fi capabilities, facilitating easy sharing and remote control through a smartphone app. This enables photographers to transfer images wirelessly and control the camera from a distance, enhancing the shooting experience.

In summary, the Pentax N-0751M and N-0751M-OD embody the perfect combination of durability, image quality, and user-friendly technology. With robust features that cater to professional demands, these cameras stand out as reliable tools for capturing stunning images in any environment. Whether for work or passion, photographers can count on the N-0751M series to deliver superior performance and exceptional results.
Top Page Image Contents