Pentax N-0751M-OD installation manual Horizontal Vent Termination, Vertical Vent Termination

Page 14

Horizontal Vent Termination

 

 

 

 

Terminate at least 300mm (12") above

 

Hanger

 

grade or above snow line.

Elbow

Straps

Terminate at least 2.1m (7') above a public

 

 

walkway, 1.8m (6') from the combustion air

 

Wall

Termination

intake of any appliance, and 0.9m (3') from

 

any other building opening, gas utility meter,

 

Slope vent Thimble

 

 

Downwards

 

service regulator etc.

 

 

Terminate at least 0.9m (3') above any

 

**0.3m (1') Min. -

 

forced air inlet within 3m (10'), 1.2m (4') be-

Appliance

0.9m (3') Max.

 

low, 1.2m (4') horizontally from or 0.3m (1')

Adapter*

 

 

above any door, window, or gravity air inlet

 

* Adapter not required when

 

into any building per National Fuel Gas Code

 

 

ANSI Z223.1/NFPA 54.

 

using Noritz N-Vent.

 

 

** 0.3m (1') minimum recommended,

• Slope the horizontal vent 1/4" downwards

 

but not required. Avoid installing

 

for every 300m (12").

 

elbow directly on flue.

 

 

 

• Use a condensation drain if necessary.

 

 

• In the Commonwealth of Massachusetts a

 

 

 

carbon monoxide detector is required for all

Vertical Vent Termination

 

side wall horizontally vented gas fuel equip-

 

ment. Please refer to Technical Bulletin TB

 

Rain

 

 

Cap

 

010606 for full installation instructions.

Storm

 

 

Collar

Roof

• Terminate at least 1.8m (6') from the combus-

 

 

Flashing

tion air intake of any appliance, and 0.9m (3')

 

 

Roof

 

from any other building opening, gas utility

Jack

 

meter, service regulator etc.

 

 

Firestop/

Support

 

Hanger

Firestop

Elbow

Strap

 

 

 

 

Condensation

 

 

Drain (Install

 

**0.3m (1') Min. -

According to

 

0.9m (3') Max.

Local Codes)

 

 

Appliance

 

 

Adapter*

 

 

* Adapter not required when

 

using Noritz N-Vent.

 

 

** 0.3m (1') minimum recommended,

 

but not required. Avoid installing

 

elbow directly on flue.

 

Enclose exterior vent systems below the roof line to limit condensation and protect against mechanical failure.

When the vent penetrates a floor or ceiling and is not running in a fire rated shaft, a firestop and support is required.

Terminate the vent system at least 0.6m (2') above, but not more than 1.8m (6') above the roof line, or according to the vent pipe manufacturer's instructions.

Terminate the vent system at least 0.6m (2') above any portion of a building located within 3m (10') horizontally.

Provide vertical support every 3.6m (12') or as required by the vent pipe manufacturer's in- structions.

Slope the horizontal vent 1/4" for every 300m (12") towards the drain tee.

Do not vent straight upwards.

Always have a horizontal section of venting.

Install a condensation drain in the horizontal section of the venting.

14

Image 14
Contents Installation Manual CanadaEach See p Remote Controller Outdoor Junction BoxPart Shape Part Shape Outdoor Vent Cap VC4-1Controller to only one System DiagramTypical Plumbing UnitsBefore Installation Choosing Installation Site With corrugatedProhibited Be sure to do 600mm 24 or more Installation ClearancesMin 75mm 200mm Or Min 75mm 3 more Maintain the following clearance from both combustible When installing the unit on a balcony, etc., secure anSuch as the wall of the second floor where the unit is out Non-combustible materialsVent Terminal 9m 3 above any forced air inlet within Window, or gravity air inlet into any buildingFor N-0751M- OD Locating Screw Holes Mounting InstallationBe damaged and may become highly dangerous Appliance Adapters Vent PipingClearances Horizontal Vent Termination Vertical Vent TerminationCombustion Air Openings supplying indoor airMeasuring Gas Pressure Gas Meter Gas PipingGas Pressure Gas ConnectionGas Line Sizing for a Noritz Gas Water Heater Hot water piping Supply water pipingDrain piping Plumbing Applications For Space Heating PurposesGround Electrical WiringBreaker Installation Heard 2 sec. and 50 C 122 F appears on the display Remote ControllerRemove the front cover of the water heater 4 screws Connecting Remote Controller Cord to Unit Remote controller cordRelay connection with larger pumps 85 W Connecting the pump control wireWire Tag Pump ControlWiring Throughway Coupling Cord Remote controller can be connected to eitherConnecting the Quick Connect Cord to the two units Unit a or BOperation of the water heater MaintenancePeriodically check the following to ensure proper Shutdown Instructions Handling after trial operationLighting Instructions 0751M-OD Dimensions0751M Connection of Remote Controller Cord For InstallersIncluded Parts List White ConnectorInstallation Remote Controller Cord Rear SideController cord outside the junction box Box NutTie the redundant length of the remote Close the junction boxProduits Natural Gas and Propane Installation Code NscngpicPas évitée, entraînera des blessures graves ou mortelles Être nécessaires à l’installation Pièce Forme Commencer l’installation Pièce FormeVoir p.21 Ce document Cordon de Télécommande Boîte de dérivation Extérieure de la TélécommandePlomberie type Télécommande à Un seul des AppareilsSchéma du système Remarque Raccordez laVérifiez le gaz Avant l’installationCheck-up Vérifiez la qualité de l’alimentation en eauChoix du site d’installation Interdit Veillez à ’exécuter Dégagement pour linstallation De calorifugeage matière incombustible autre que le Indique la distance lors de linstallation dune plaqueLorsque vous installez lunité sur un balcon, etc., laissez Métal, dune épaisseur de 2.5mm 0.1 ou plus ouEntrée d’alimentati on en air 2m 4 dessous, 1.2m Maintenez les dégagements suivants parRapport aux ouvertures d’un bâtiment Horizontalement à partir de, ou 0.3mCache déposé Installation dun boîtier encastré avecEncastr 3m 1 dessous, 0.3m Fixation au mur Dégagement Installation du tuyau d’évent uniquementTuyauterie de l’évent Adaptateurs d’appareilBouche de l’évent horizontal Bouche de l’évent verticalAir comburant Ouvertures alimentant en air intérieurRaccordement de gaz Pression du gazMesure de la pression du gaz Compteur à gaz Adapté de UC1997 Conduite d’eau Plomberie Pour le chauffage du bâtimentAdressez-vous à un électricien Qualifié pour l’installation électriqueInstallation du disjoncteur TerreTélécommande Coupez lalimentation électrique du chauffe-eauAttache Câble 18AWG Raccordement du cordon de télécommande à l’unitéCordon de télécommande Raccordement du câble de commande de la pompe Connexion par relais avec de grandes pompes 85WBranchement du cordon de raccordement rapide aux deux unités Connecteur Attache Ouverture pour Cordon de Câbles CouplageVérifiez régulièrement les points suivants pour Garantir un bon fonctionnement du chauffe-eauInstructions d’arrêt Manipulation après le test de fonctionnementInstructions d’allumage 10mm Nom des pièces Quantité Télécommande Garniture du mur Pour les installateursRemarques sur l’emplacement d’installation RemarqueInstallation La boîte Attachez le cordon de la télécommandeÉcrou de Qui dépasse à l’extérieur de la boîte de

N-0751M-OD, N-0751M specifications

The Pentax N-0751M and N-0751M-OD are advanced digital cameras designed primarily for outdoor and rugged environments. These models exemplify the blend of functionality and durability that Pentax is known for, appealing to both photography enthusiasts and professionals who require reliable equipment in demanding conditions.

One of the standout features of the N-0751M and its counterpart, the N-0751M-OD, is their robust construction. Built to withstand harsh environments, these cameras are weather-resistant, ensuring that they can handle rain, dust, and extreme temperatures. This makes them ideal for nature photographers, adventure enthusiasts, and even those who work in challenging conditions.

The N-0751M series is equipped with a high-resolution sensor that captures stunning images with remarkable clarity and detail. The camera features an advanced image processing engine that enhances color accuracy and dynamic range, allowing users to create vibrant and lifelike photos. This sensor also performs exceptionally well in low-light environments, making it versatile for various shooting situations.

Another key characteristic of the N-0751M and N-0751M-OD is their fast and responsive autofocus system. This ensures that users can quickly lock onto their subjects, which is critical for capturing fleeting moments, whether in wildlife photography or action sports. The cameras also come with multiple autofocus modes and options, providing photographers with the flexibility to choose the best setting for their shooting style.

In terms of usability, the N-0751M series features an intuitive interface with customizable settings that allow users to adapt the camera to their personal preferences. The ergonomic design promotes comfort during extended shooting sessions, making it easy to navigate through menus and settings quickly.

For connectivity, the N-0751M and N-0751M-OD come equipped with Wi-Fi capabilities, facilitating easy sharing and remote control through a smartphone app. This enables photographers to transfer images wirelessly and control the camera from a distance, enhancing the shooting experience.

In summary, the Pentax N-0751M and N-0751M-OD embody the perfect combination of durability, image quality, and user-friendly technology. With robust features that cater to professional demands, these cameras stand out as reliable tools for capturing stunning images in any environment. Whether for work or passion, photographers can count on the N-0751M series to deliver superior performance and exceptional results.