Pentax N-0751M-OD Box Nut, Tie the redundant length of the remote, Close the junction box

Page 30

[For outdoor installation only]

Installing the Remote Controller Outdoor Junction Box

1. Insert the remote controller wires through the

5.

Slide the box nut over the remote controller

wall pipe and secure the wall pipe to the

 

wires and screw it onto the wall pipe.

remote controller. Locate the remote controller

 

 

wall packing, slide it over the pipe and wires,

 

Wall Pipe

and apply it to the rear side of the remote.

 

 

 

Rear side of remote controller

 

Box Nut

 

 

 

 

 

 

Remote

 

Wall Packing

 

Controller

Secure the wall pipe

 

 

Wires

 

 

 

firmly into the remote

 

 

 

controller.

 

 

 

Take off the

 

 

 

paper.

 

 

 

2. Drill a 32mm ( 1-1/4") hole in the wall

6.

Connect the remote controller wires to the

where the remote controller will be installed.

 

separate remote controller cord inside the box.

 

 

 

Wind the excess remote controller wire on the

* Do not install the remote controller in a

 

provided hooks as illustrated below.

location that is exposed to moisture, direct

 

(Wind the

sunlight, or chemical agents. These can

 

excess wire

damage the remote controller.

 

here.)

 

 

 

Remote Controller

 

 

 

Wires

3. Insert the wall pipe containing the remote

 

Junction Box

controller wires through the hole.

 

 

 

4. Slide the junction box packing and the junction

 

Remote Controller

box over the remote controller wires and wall

 

 

Cord

pipe protruding from the outside wall.

 

 

 

Wall packing

Wall pipe

 

 

 

 

 

 

Take out the pipe about

 

Tie the redundant length of the remote

 

18.75mm (3/4") from

 

controller cord outside the junction box.

 

the wall.

 

 

 

Junction Box

7. Close the junction box.

 

Box Nut

 

 

 

 

Remote

 

 

 

Controller

 

 

 

Wires

 

 

Take off the paper.

 

 

 

 

Junction Box Packing

 

 

30

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Installation Manual CanadaEach See p Remote Controller Outdoor Junction BoxPart Shape Part Shape Outdoor Vent Cap VC4-1Controller to only one System DiagramTypical Plumbing UnitsBefore Installation Choosing Installation Site With corrugatedProhibited Be sure to do Installation Clearances Min 75mm 200mm Or Min 75mm 3 more600mm 24 or more Maintain the following clearance from both combustible When installing the unit on a balcony, etc., secure anSuch as the wall of the second floor where the unit is out Non-combustible materialsVent Terminal 9m 3 above any forced air inlet within Window, or gravity air inlet into any buildingFor N-0751M- OD Installation Be damaged and may become highly dangerousLocating Screw Holes Mounting Vent Piping ClearancesAppliance Adapters Horizontal Vent Termination Vertical Vent TerminationCombustion Air Openings supplying indoor airMeasuring Gas Pressure Gas Meter Gas PipingGas Pressure Gas ConnectionGas Line Sizing for a Noritz Gas Water Heater Supply water piping Drain pipingHot water piping Plumbing Applications For Space Heating PurposesElectrical Wiring Breaker InstallationGround Remote Controller Remove the front cover of the water heater 4 screwsHeard 2 sec. and 50 C 122 F appears on the display Connecting Remote Controller Cord to Unit Remote controller cordRelay connection with larger pumps 85 W Connecting the pump control wireWire Tag Pump ControlWiring Throughway Coupling Cord Remote controller can be connected to eitherConnecting the Quick Connect Cord to the two units Unit a or BMaintenance Periodically check the following to ensure properOperation of the water heater Handling after trial operation Lighting InstructionsShutdown Instructions Dimensions 0751M0751M-OD Connection of Remote Controller Cord For InstallersIncluded Parts List White ConnectorInstallation Remote Controller Cord Rear SideController cord outside the junction box Box NutTie the redundant length of the remote Close the junction boxNatural Gas and Propane Installation Code Nscngpic Pas évitée, entraînera des blessures graves ou mortellesProduits Être nécessaires à l’installation Pièce Forme Commencer l’installation Pièce FormeVoir p.21 Ce document Cordon de Télécommande Boîte de dérivation Extérieure de la TélécommandePlomberie type Télécommande à Un seul des AppareilsSchéma du système Remarque Raccordez laVérifiez le gaz Avant l’installationCheck-up Vérifiez la qualité de l’alimentation en eauChoix du site d’installation Interdit Veillez à ’exécuter Dégagement pour linstallation De calorifugeage matière incombustible autre que le Indique la distance lors de linstallation dune plaqueLorsque vous installez lunité sur un balcon, etc., laissez Métal, dune épaisseur de 2.5mm 0.1 ou plus ouEntrée d’alimentati on en air 2m 4 dessous, 1.2m Maintenez les dégagements suivants parRapport aux ouvertures d’un bâtiment Horizontalement à partir de, ou 0.3mInstallation dun boîtier encastré avec Encastr 3m 1 dessous, 0.3mCache déposé Fixation au mur Dégagement Installation du tuyau d’évent uniquementTuyauterie de l’évent Adaptateurs d’appareilBouche de l’évent horizontal Bouche de l’évent verticalAir comburant Ouvertures alimentant en air intérieurPression du gaz Mesure de la pression du gaz Compteur à gazRaccordement de gaz Adapté de UC1997 Conduite d’eau Plomberie Pour le chauffage du bâtimentAdressez-vous à un électricien Qualifié pour l’installation électriqueInstallation du disjoncteur TerreTélécommande Coupez lalimentation électrique du chauffe-eauRaccordement du cordon de télécommande à l’unité Cordon de télécommandeAttache Câble 18AWG Raccordement du câble de commande de la pompe Connexion par relais avec de grandes pompes 85WBranchement du cordon de raccordement rapide aux deux unités Connecteur Attache Ouverture pour Cordon de Câbles CouplageVérifiez régulièrement les points suivants pour Garantir un bon fonctionnement du chauffe-eauManipulation après le test de fonctionnement Instructions d’allumageInstructions d’arrêt 10mm Nom des pièces Quantité Télécommande Garniture du mur Pour les installateursRemarques sur l’emplacement d’installation RemarqueInstallation La boîte Attachez le cordon de la télécommandeÉcrou de Qui dépasse à l’extérieur de la boîte de

N-0751M-OD, N-0751M specifications

The Pentax N-0751M and N-0751M-OD are advanced digital cameras designed primarily for outdoor and rugged environments. These models exemplify the blend of functionality and durability that Pentax is known for, appealing to both photography enthusiasts and professionals who require reliable equipment in demanding conditions.

One of the standout features of the N-0751M and its counterpart, the N-0751M-OD, is their robust construction. Built to withstand harsh environments, these cameras are weather-resistant, ensuring that they can handle rain, dust, and extreme temperatures. This makes them ideal for nature photographers, adventure enthusiasts, and even those who work in challenging conditions.

The N-0751M series is equipped with a high-resolution sensor that captures stunning images with remarkable clarity and detail. The camera features an advanced image processing engine that enhances color accuracy and dynamic range, allowing users to create vibrant and lifelike photos. This sensor also performs exceptionally well in low-light environments, making it versatile for various shooting situations.

Another key characteristic of the N-0751M and N-0751M-OD is their fast and responsive autofocus system. This ensures that users can quickly lock onto their subjects, which is critical for capturing fleeting moments, whether in wildlife photography or action sports. The cameras also come with multiple autofocus modes and options, providing photographers with the flexibility to choose the best setting for their shooting style.

In terms of usability, the N-0751M series features an intuitive interface with customizable settings that allow users to adapt the camera to their personal preferences. The ergonomic design promotes comfort during extended shooting sessions, making it easy to navigate through menus and settings quickly.

For connectivity, the N-0751M and N-0751M-OD come equipped with Wi-Fi capabilities, facilitating easy sharing and remote control through a smartphone app. This enables photographers to transfer images wirelessly and control the camera from a distance, enhancing the shooting experience.

In summary, the Pentax N-0751M and N-0751M-OD embody the perfect combination of durability, image quality, and user-friendly technology. With robust features that cater to professional demands, these cameras stand out as reliable tools for capturing stunning images in any environment. Whether for work or passion, photographers can count on the N-0751M series to deliver superior performance and exceptional results.
Top Page Image Contents