Nilfisk-ALTO SR 1700 2WD B Cleaning and Maintenance, Periodical Maintenance, Maintenance Table

Page 58

USER MANUAL

CLEANING AND MAINTENANCE

The machine cleaning can be carried out by non-specialized personnel. However, the person in charge of the cleaning should be familiar with the energy source cut-off main controls and the main features of the machine to avoid any dangerous situation.

The machine maintenance should be carried out by highly skilled personnel, with a deep knowledge of the machine and its components.

Mechanical, electrical and electronic maintenance is possible.

WARNING!

Any cleaning and maintenance operation should be carried out with the machine off. Wait for all the parts to stop and cool down.

WARNING!

Protect eyes and hair when cleaning the machine with compressed air guns.

If the machine is working in a toxic environment, wear a special mask and adequate protective clothing when carrying out maintenance work on the dust filter.

CLEANING

Machine general cleaning

Clean the coating, panels and controls of the machine with a soft cloth, either dry or lightly soaked in a mild detergent solution.

NOTE

Do not use solvents such as alcohol, petrol or ethyl acetate as they could damage the surfaces.

Remove traces of dust and other dirt from the machine control panels (digital displays, indicator and warning lights, switches).

NOTE

Pay attention when cleaning the electrical components.

If necessary, the electrical components should be cleaned only by specialized personnel and non-corrosive products suitable for electric circuits should be used.

PERIODICAL MAINTENANCE

WARNING!

Any cleaning and maintenance operation should be carried out with the machine off. Wait for all the parts to stop and cool down.

For the engine maintenance, please follow the instructions provided in the Use and Maintenance Manual concerning the engine installed on the sweeper. This manual comes in a special case.

Recommended periodical maintenance operations are summarized in this table.

MAINTENANCE TABLE

 

Every 10

Every 20

After 50

Every 150

Every 300

Every

Every

Maintenance

1,000

2,000

hours

hours

hours

hours

hours

 

hours

hours

 

 

 

 

 

 

Hydraulic oil level check

Closed pocket filter cleaning

Battery check

Brake fluid level check

Battery check

Dust control system water filter check

Gear pump hydraulic oil filter replacement

Hydrostatic pump hydraulic oil filter replacement

Hydrostatic pump hydraulic oil filter replacement

Screw tightening

Hydraulic oil change

Motor carbon brush check

Hydraulic motor and pump pressure check

Brake system check

Moving part clearance check

14

33014816(1)2005-07 A

Image 58
Contents Sweeper 3301481612005-07 aEC Low Voltage Modell/Modèle/Model/ModelEN 60335-1, EN Directive 73/23301481612005-07 a Page Betriebsanleitung Allgemeine AnweisungenVorbedingung EinleitungAllgemeine Anweisungen MaschinenidentifizierungVerantwortlichkeit DES Bedieners Terminologien UND Ihre BedeutungSicherheitsvorschriften Warnzeichen TRANSPORT, VERLAGERUNG, InstallationAblanden UND Verlagern Technische Eigenschaften Maschinenbeschreibung Stabilität SicherheitssystemeTechnische Daten Informationen zu den BürstenGeräuschpegel AnwendungUmgebungswerte Steuerungen UND InstrumenteGebrauchsanweisungen Gebrauch DER MaschineMaschinenabstellen Störungen UND Abhilfen Störungen UND AbhilfenDie Dichtung des Flaps wird von der Bürste Übermäßige Erwärmung Ursache Prüfen AbhilfePlanmässige Wartung Reinigung UND WartungReinigung WartungstabelleGleichstrom-Fahrmotor Planmässige Prüfungen Ausserordentliche WartungBetriebsbatterie Abbau ABBAU, EntsorgungEntsorgung Schaltplan PläneSchutzplatine RelaisplatineHydraulikplan Siehe Abb. AFManuel Dutilisation Introduction Avertissements GenerauxTerminologie ET Signification Precautions Pour LA Securite DES OperateursResponsabilite DE Loperateur Signaux Dattention TRANSPORT, MANUTENTION, InstallationDechargement ET Manutention Controles Generaux Caracteristiques TechniquesEmballages Utilisation PrevueDescription DE LA Machine Stabilité Systemes DE SecuriteDonnees Techniques Principales Informations sur les brossesValeurs Environnementales Commandes ET InstrumentsUtilisation Niveau DE BruitInstructions Pour Lutilisation Utilisation DE LA MachineArret DE LA Machine Problemes ET Remedes Problemes ET RemedesLa brosse centrale ne descend / monte pas Réchauffement excessif Cause Verifier RemedeEntretien Periodique Nettoyage ET EntretienNettoyage Tableau DentretienMoteur à courant continu de traction Controles Periodiques Entretien ExtraordinaireBatterie DE Service Demantelement DEMANTELEMENT, EcoulementEcoulement Carte Fusibles SchemasSchema Electrique Carte RelaisSchema Hydraulique Voir Fig. AFIntroduction Machine Identification General WarningsForeword Purpose Safe-KeepingOperators Responsibility Operators Safety PrecautionsDefinitions Exposed personTRANSPORTATION, HANDLING, Installation Discharge and HandlingGeneral Checks Technical DataPacking USEMachine Description Stability Safety SystemsMain Technical Data Information on broomsNoise Level USEEnvironmental Conditions Controls and InstrumentsInstructions for USE Machine USEMachine Stop Problems and Remedies Problems and Remedies3301481612005-07 a Overheating Cause Check RemedyPeriodical Maintenance Cleaning and MaintenanceCleaning Maintenance TableDrive direct current motor Extraordinary Maintenance Periodical ChecksAccessory Battery Dismantling DISMANTLING, DisposalDisposal Fuse Board DiagramsWiring Diagram Relay BoardHydraulic Diagram See Fig. AFGebruikershandleiding Algemene WaarschuwingenVoorwoord InleidingAlgemene Waarschuwingen Identificatie VAN DE MachineVeiligheidsmaatregelen Voor DE Bediener DefinitiesVerantwoordelijkheid VAN DE Bediener GevarenzonesWaarschuwingstekens VERVOER, HANTERING, InstallatieLossen EN Bediening Technische Gegevens Beschrijving VAN DE Machine Stabiliteit VeiligheidssystemenBelangrijkste Technische Gegevens Informatie over borstelsGeluidsniveau GebruikMilieu Bedieningen EN InstrumentenGebruiksinstructies Gebruik VAN DE MachineMachinestop Problemen EN Oplossingen Problemen EN OplossingenGebruikershandleiding Oververhitting Oorzaak Controleren OplossingPeriodiek Onderhoud Reiniging EN OnderhoudOnderhoudstabel Reiniging Algemene reiniging van de machineAandrijving gelijkstroommotor CollectorPeriodieke Controles Buitengewoon OnderhoudExtra Accu Demonteren DEMONTEREN, AfdankenAfdanken Zekeringenbord SCHEMA’SBedradingsschema RelaisbordSchema Hydraulica Zie Afb. AF3301481612005-07 a 3301481612005-07 a 3301481612005-07 a 3301481612005-07 a 3301481612005-07 a 3301481612005-07 a 3301481612005-07 a Page 3301481612005-07 a 210 3301481612005-07 a Nilfisk-Advance SpA

SR 1700 2WD B specifications

The Nilfisk-ALTO SR 1700 2WD B is a powerful ride-on scrubber dryer, specially designed for medium to large indoor areas such as retail spaces, warehouses, and industrial facilities. Built with efficiency and user comfort in mind, this advanced cleaning machine provides exceptional performance with several key features and innovative technologies that set it apart from its competitors.

One of the standout features of the SR 1700 2WD B is its effective dual-brush system that facilitates thorough cleaning of various floor types. The dual rotating brushes ensure an even, deep clean and can easily remove ingrained dirt and grime, leaving surfaces spotless. Furthermore, the adjustable brush pressure allows operators to customize cleaning according to specific surface requirements, optimizing performance while minimizing wear on brushes.

Equipped with a highly efficient vacuum system, the Nilfisk-ALTO SR 1700 2WD B excels in liquid recovery. It effectively picks up water and cleaning solution, resulting in safer, cleaner floors that dry quickly. This feature is particularly beneficial in high-traffic environments where slip hazards must be minimized.

The SR 1700 2WD B also features a reliable and easy-to-use control panel, which makes operation straightforward for any user. The intuitive design reduces the learning curve, allowing operators to concentrate on cleaning rather than grappling with complicated controls. Additionally, the ergonomic driving position enhances comfort during longer shifts, reducing fatigue and improving productivity.

Safety is a critical aspect of the Nilfisk-ALTO SR 1700 2WD B. The machine is designed with several safety features, including an automatic shut-off function to prevent accidents in case of operator error. Furthermore, the low center of gravity design improves stability while maneuvering, particularly in tight spaces and corners.

Moreover, the Nilfisk-ALTO SR 1700 2WD B is built to be environmentally friendly. It effectively reduces water and chemical consumption through its efficient cleaning system, contributing to sustainable cleaning practices. The robust build quality ensures a long lifespan, reducing the need for frequent replacements and minimizing waste.

Overall, the Nilfisk-ALTO SR 1700 2WD B combines cutting-edge technology with user-friendly design, offering reliability, efficiency, and superior cleaning results. Its combination of superior suction, adjustable brush pressure, and safety features make it an excellent choice for any facility looking to enhance its cleaning operations. The machine not only meets but exceeds the expectations of modern cleaning environments.