Nilfisk-ALTO SR 1700 2WD B Technical Data, Packing, General Checks, Use, Machine Layout

Page 49

USER MANUAL

Before handling the machine, the route from where the vehicle is parked to where the machine is to be installed should be checked beforehand for any danger areas.

NOTE

Check that the floor is not too uneven, avoid driving the vehicle at high speeds, and avoid excessive swaying of the transported machine.

WARNING!

It is forbidden to get onto the machine, or stand or walk under it.

Lift the machine or the boxes as needed to handle the machine.

PACKING

Packing should be disposed according to the law in force.

INSTALLATION

When delivered, the machine is completely assembled and perfectly working, so it does not require any installation by the customer.

GENERAL CHECKS

–Make sure the machine has been inspected before delivery (check the warranty).

–Check that the machine has not suffered any damage during transportation and carry out the preliminary operations for setting the machine at work according to the instructions in the manual.

–Check the hydraulic system oil level in the tank.

–Check the brake fluid level.

–Start the machine.

–Follow the maintenance instructions.

TECHNICAL DATA

USE

The SR 1700 2WD B sweeper has been designed to perform a complete cycle of industrial and urban cleaning: sweeping, waste collecting and dumping.

NOTE

Any use other than the one described can damage the machine or injure the operators.

The sweeping is carried out by one or more side brooms which convey the debris towards the centre of the machine and a cylindrical main broom sweeps the collected debris into the hopper. The dust is collected and controlled by a fan. The air released into the environment is filtered by a filter. The waste collected in the hopper may be dumped onto the ground or into special boxes at a maximum height of 1,510 mm.

MACHINE LAYOUT

(See Fig. E)

1.Fan

2.Side broom

3.Hydraulic system oil tank

4.Steering wheel with power steering

5.Battery

6.Drive hydraulic motor

7.Blower

8.Rear wheel

9.Frame

10.Engine

11.Drive hydraulic pump

12.Main broom hydraulic motor

13.Main broom

14.Accessory hydraulic pump

15.Dust suction filter

16.Hopper

17.Front wheels

18.Side broom hydraulic motor

33014816(1)2005-07 A

5

Page 48 Page 50
Image 49
Page 48 Page 50
Contents 3301481612005-07 a SweeperEN 60335-1, EN Modell/Modèle/Model/ModelEC Low Voltage Directive 73/23301481612005-07 a Page Allgemeine Anweisungen BetriebsanleitungAllgemeine Anweisungen EinleitungVorbedingung MaschinenidentifizierungVerantwortlichkeit DES Bedieners Terminologien UND Ihre BedeutungSicherheitsvorschriften Warnzeichen TRANSPORT, VERLAGERUNG, InstallationAblanden UND Verlagern Technische Eigenschaften Maschinenbeschreibung Technische Daten SicherheitssystemeStabilität Informationen zu den BürstenUmgebungswerte AnwendungGeräuschpegel Steuerungen UND InstrumenteGebrauch DER Maschine GebrauchsanweisungenMaschinenabstellen Störungen UND Abhilfen Störungen UND AbhilfenDie Dichtung des Flaps wird von der Bürste Ursache Prüfen Abhilfe Übermäßige ErwärmungReinigung Reinigung UND WartungPlanmässige Wartung WartungstabelleGleichstrom-Fahrmotor Ausserordentliche Wartung Planmässige PrüfungenBetriebsbatterie Abbau ABBAU, EntsorgungEntsorgung Schutzplatine PläneSchaltplan RelaisplatineSiehe Abb. AF HydraulikplanManuel Dutilisation Avertissements Generaux IntroductionTerminologie ET Signification Precautions Pour LA Securite DES OperateursResponsabilite DE Loperateur Signaux Dattention TRANSPORT, MANUTENTION, InstallationDechargement ET Manutention Emballages Caracteristiques TechniquesControles Generaux Utilisation PrevueDescription DE LA Machine Donnees Techniques Principales Systemes DE SecuriteStabilité Informations sur les brossesUtilisation Commandes ET InstrumentsValeurs Environnementales Niveau DE BruitUtilisation DE LA Machine Instructions Pour LutilisationArret DE LA Machine Problemes ET Remedes Problemes ET RemedesLa brosse centrale ne descend / monte pas Cause Verifier Remede Réchauffement excessifNettoyage Nettoyage ET EntretienEntretien Periodique Tableau DentretienMoteur à courant continu de traction Entretien Extraordinaire Controles PeriodiquesBatterie DE Service Demantelement DEMANTELEMENT, EcoulementEcoulement Schema Electrique SchemasCarte Fusibles Carte RelaisVoir Fig. AF Schema HydrauliqueIntroduction Foreword General WarningsMachine Identification Purpose Safe-KeepingDefinitions Operators Safety PrecautionsOperators Responsibility Exposed personDischarge and Handling TRANSPORTATION, HANDLING, InstallationPacking Technical DataGeneral Checks USEMachine Description Main Technical Data Safety SystemsStability Information on broomsEnvironmental Conditions USENoise Level Controls and InstrumentsMachine USE Instructions for USEMachine Stop Problems and Remedies Problems and Remedies3301481612005-07 a Cause Check Remedy OverheatingCleaning Cleaning and MaintenancePeriodical Maintenance Maintenance TableDrive direct current motor Periodical Checks Extraordinary MaintenanceAccessory Battery Dismantling DISMANTLING, DisposalDisposal Wiring Diagram DiagramsFuse Board Relay BoardSee Fig. AF Hydraulic DiagramAlgemene Waarschuwingen GebruikershandleidingAlgemene Waarschuwingen InleidingVoorwoord Identificatie VAN DE MachineVerantwoordelijkheid VAN DE Bediener DefinitiesVeiligheidsmaatregelen Voor DE Bediener GevarenzonesWaarschuwingstekens VERVOER, HANTERING, InstallatieLossen EN Bediening Technische Gegevens Beschrijving VAN DE Machine Belangrijkste Technische Gegevens VeiligheidssystemenStabiliteit Informatie over borstelsMilieu GebruikGeluidsniveau Bedieningen EN InstrumentenGebruik VAN DE Machine GebruiksinstructiesMachinestop Problemen EN Oplossingen Problemen EN OplossingenGebruikershandleiding Oorzaak Controleren Oplossing OververhittingOnderhoudstabel Reiniging Reiniging EN OnderhoudPeriodiek Onderhoud Algemene reiniging van de machineCollector Aandrijving gelijkstroommotorBuitengewoon Onderhoud Periodieke ControlesExtra Accu Demonteren DEMONTEREN, AfdankenAfdanken Bedradingsschema SCHEMA’SZekeringenbord RelaisbordZie Afb. AF Schema Hydraulica3301481612005-07 a 3301481612005-07 a 3301481612005-07 a 3301481612005-07 a 3301481612005-07 a 3301481612005-07 a 3301481612005-07 a Page 3301481612005-07 a 210 3301481612005-07 a Nilfisk-Advance SpA

SR 1700 2WD B specifications

The Nilfisk-ALTO SR 1700 2WD B is a powerful ride-on scrubber dryer, specially designed for medium to large indoor areas such as retail spaces, warehouses, and industrial facilities. Built with efficiency and user comfort in mind, this advanced cleaning machine provides exceptional performance with several key features and innovative technologies that set it apart from its competitors.

One of the standout features of the SR 1700 2WD B is its effective dual-brush system that facilitates thorough cleaning of various floor types. The dual rotating brushes ensure an even, deep clean and can easily remove ingrained dirt and grime, leaving surfaces spotless. Furthermore, the adjustable brush pressure allows operators to customize cleaning according to specific surface requirements, optimizing performance while minimizing wear on brushes.

Equipped with a highly efficient vacuum system, the Nilfisk-ALTO SR 1700 2WD B excels in liquid recovery. It effectively picks up water and cleaning solution, resulting in safer, cleaner floors that dry quickly. This feature is particularly beneficial in high-traffic environments where slip hazards must be minimized.

The SR 1700 2WD B also features a reliable and easy-to-use control panel, which makes operation straightforward for any user. The intuitive design reduces the learning curve, allowing operators to concentrate on cleaning rather than grappling with complicated controls. Additionally, the ergonomic driving position enhances comfort during longer shifts, reducing fatigue and improving productivity.

Safety is a critical aspect of the Nilfisk-ALTO SR 1700 2WD B. The machine is designed with several safety features, including an automatic shut-off function to prevent accidents in case of operator error. Furthermore, the low center of gravity design improves stability while maneuvering, particularly in tight spaces and corners.

Moreover, the Nilfisk-ALTO SR 1700 2WD B is built to be environmentally friendly. It effectively reduces water and chemical consumption through its efficient cleaning system, contributing to sustainable cleaning practices. The robust build quality ensures a long lifespan, reducing the need for frequent replacements and minimizing waste.

Overall, the Nilfisk-ALTO SR 1700 2WD B combines cutting-edge technology with user-friendly design, offering reliability, efficiency, and superior cleaning results. Its combination of superior suction, adjustable brush pressure, and safety features make it an excellent choice for any facility looking to enhance its cleaning operations. The machine not only meets but exceeds the expectations of modern cleaning environments.
Top Page Image Contents