Integra DTR-8.4 Zone 2 OUT, Dvd, Video 1 & 2 IN/OUT 29, Video 3 & 4, Ethernet Net-Tune, RS232

DTR-8.4_En.book Page 13 Thursday, October 16, 2003 11:09 AM

Front & Rear Panels—Continued

JTAPE IN/OUT (34)

These analog inputs and outputs can be used to con- nect a cassette recorder, Mini Disc recorder, or other recorder with analog inputs and outputs.

KMONITOR OUT (27)

This S-Video or composite video output can be con- nected to the video input on your TV or projector.

LZONE 2 OUT (84)

These composite video and analog audio outputs can be used to feed a TV and an integrated amp in Zone 2.

MDVD IN (28)

These S-Video, composite video, and analog audio inputs can be used to connect a DVD player.

NVIDEO 1 & 2 IN/OUT (29, 31)

These S-Video, composite video, and analog audio inputs and outputs can be used to connect one or two video recorders (e.g., VCRs).

OVIDEO 3 & 4 IN (31)

These S-Video, composite video, and analog audio inputs can be used to connect one or two video sources (e.g., cable TV, satellite TV, or a set-top box).

PCOMPONENT VIDEO OUTPUT (27)

This component video output can be used to con- nect a TV or projector with a component video input.

QCOMPONENT VIDEO INPUT 1 & 2 (28, 30, 32)

These component video inputs can be used to con- nect one or two AV components with component video outputs, such as a DVD player.

RETHERNET (Net-Tune) (76)

This port is for connecting the DTR-8.4 to your Ethernet network (i.e., router or switch) for use with Net-Tune (i.e., Internet radio and MP3 and WAV playback).

SSPEAKERS (23)

These terminal posts are for connecting your speak- ers. The SURR BACK/ZONE 2 terminals can be used with surround back speakers in the main room or speakers in another room (Zone 2).

TRS232 (37)

This port is for connecting the DTR-8.4 to home automation and external controllers.

UIR IN/OUT (85)

If you want to use the remote controller to control the DTR-8.4 from Zone 2, or if the DTR-8.4 is installed in a cabinet and the line of sight between the DTR-8.4 and the remote controller is obstructed, a commercially available IR receiver can be con- nected to the IR IN. A commercially available IR emitter can be connected to the IR OUT to pass the IR signals along to another AV component.

V12V TRIGGER OUT ZONE 2/A/B (68, 85)

These outputs can be connected to the 12-volt trig- ger inputs on other components. They output 12 volts (100 milliamperes max). The ZONE 2 TRIG- GER OUT outputs 12 volts while the DTR-8.4 is in Zone 2 mode. The A and B outputs can be assigned to input sources, in which case, the assigned trigger output outputs 12 volts while the input source is selected.

W REMOTE CONTROL (36)

This (Remote Interactive) socket can be con-

nected to the socket on another Integra/Onkyo AV component. The DTR-8.4’s remote controller can then be used to control that component. To use

, you must make an analog RCA/phono audio connection between the DTR-8.4 and the other AV component, even if they are connected digitally.

XAC INLET (37)

The supplied power cord should be connected here.

YAC OUTLETS (37)

These switched AC outlets can be used to supply power to other AV components. The connector type depends on the country in which you purchased your DTR-8.4.

ZGrounding screw (35)

This screw is for connecting a turntable’s ground wire.

13