Integra DTR-8.4 instruction manual Recording Separate AV Sources

Page 66

DTR-8.4_En.book Page 66 Thursday, October 16, 2003 11:09 AM

Advanced Operation—Continued

Recording Separate AV Sources

You can record audio and video from separate sources, allowing you to dub audio onto your video recordings. In the following example, audio from the CD player con- nected to the CD IN input, and video from the camcorder connected to the VIDEO 5 INPUT VIDEO input are recorded to the VCR connected to the VIDEO 1 OUT output.

Standby/On

Master Volume

Standby

Direct/

Zone 2 (GRN)

Pure Audio

Audio

Rec (RED)

DVD

Video 1

Video 2

Video 3

Video 4

Video 5

Tape

Tuner

Phono

CD

Net Audio

Pure Audio

U psampling

Selector

Display

VCR 1

VCR 2

Phones

Zone 2 Level

Rec Out

Zone 2

Off

Stereo

Surround

THX

DSP

Dimmer Memory

FM Mode Setup

Tuning

Enter

Preset

Return

Video 5 Input

Clear

Digital

S Video

Video

L Audio R

7

1, 2 1

3, 4 3–5 2, 5

4

5

Use the Up/Down []/[ ] but- tons to select “3. Video Setup,” and then press the [Enter] but- ton.

The Video Setup menu appears.

Advanced Menu

2.Input Setup Input:DVD

2-3.Video Setup

Input:CD

a.Video

:Last Valid

b.Component Video :Last Valid

Quit:SETUP

Use the Up/Down [ ]/[	] but-
tons to select “a. Video,” and
then use the Left/Right [	]/[	]

buttons to select “VIDEO5.”

Press the [Setup] button to close the setup menu.

	1	Press the [Input] button, and then
	1	roll the scroll wheel to select the
		roll the scroll wheel to select the

6	Prepare your CD player and cam-
	Prepare your CD player and cam-
	corder for playback, and your
	VCR for recording.

CD input source.

2	Press the scroll wheel, and then
	Press the scroll wheel, and then
	press the [Setup] button.
	The main menu appears onscreen.

7

DTR-8.4

Rec Out

Press the [Rec Out] button repeatedly until “Rec Sel: SOURCE” appears on the dis- play.

Audio from the CD player and video from the camcorder can now be recorded by the VCR connected to the VIDEO 1 OUT outputs.

3 Use the Up/Down []/[ ] but- tons to select “2. Input Setup,” and then press the [Enter] but- ton.

The Input Setup menu appears.

8	Start recording on the VCR and
	Start recording on the VCR and
	start playback on the camcorder
	and CD player.

Note:

•For advanced audio dubbing, if you assign the VIDEO 5 INPUT VIDEO input to an additional input source, say, the TAPE IN input, you can dub audio from two sources and use the [CD] and [Tape] input selector buttons to switch between them during recording.

66

Image 66

Contents DTR-8.4 Important Safety Instructions AvisPrecautions PowerFCC Information for User Table of Contents Table of Contents Audio/Video FeaturesAmp FM/AM TunerPower cord Supplied AccessoriesMake sure you have the following accessories Speaker cable labels 75/300-ohm antenna adapterBefore Using the DTR-8.4 Installing the BatteriesUsing the Remote Controller Front & Rear Panels Front PanelFront & Rear Panels Display Rear Panel These push terminals are for connecting an AM antennaThis connector is for connecting an FM antenna Digital in Coax 1-3, OPT 1-4 28, 30, 32, 34Video 1 & 2 IN/OUT 29 Zone 2 OUTDVD Video 3 & 4Remote Controller Amp ModeRemote Controller Net-Tune ModeDVD Mode Last Memory button Menu buttonAngle button Search buttonCD Mode Previous/Next ButtonsRH N Muting button MiniDisc Mode FR/FF ButtonsRec button Tape Mode Rewind/FF / buttonsReverse Play button About Home Theater Enjoying Home TheaterSpeaker Conﬁguration Connecting the DTR-8.4 Positioning Your SpeakersAttaching the Speaker Labels Connecting the Speaker Cables Connecting the DTR-8.4Connecting Your Speakers Connecting a Powered SubwooferConnecting the Indoor FM Antenna Connecting AntennaConnecting the AM Loop Antenna Attach the FM antenna, as shown A. and Canadian ModelsConnecting an Outdoor FM Antenna Connecting an Outdoor AM AntennaOptical Digital Inputs Before Making Any ConnectionsAV Cables & Sockets RCA/phono AV Connection Color CodingUsing S-Video Connecting Your TV or ProjectorUsing Composite Video Using Component VideoUsing Analog Connections Connecting a DVD PlayerUsing Coaxial or Optical Connections Video ConnectionsConnecting a VCR for Playback Using Multichannel ConnectionsYou can play a video from a VCR via the DTR-8.4 Connecting a D-VHS VCR for Playback Connecting a VCR for Recording Playback from the Recording VCRPRSatellite, cable, set-top box, LD player, etc TV, Satellite, cable, set-top box, LD player, etcConnecting a Camcorder, Games Console, etc Camcorder Games console, etcCamcorder Connecting a DAT, CD, or MD Recorder Connecting a CD PlayerConnecting a Cassette Recorder Using Optical or Coaxial ConnectionsDigital Recording Connecting a TurntableUsing Coaxial or Optical Connections playback only Digital source DAT, CD, MD playerWith Remote Interactive you can control your Connecting a Power AmpConnecting Components Following special functionsConnecting the Power Cord Connecting the Power Cords of Other ComponentsConnecting the RS232 Port Standby indicator lights upPress the Standby/On button to turn on the DTR-8.4 Turning On the DTR-8.4 with the Remote ControllerTurning On the DTR-8.4 Press the scroll wheelTHX Basic Setup Speaker SettingsSpeaker Impedance Speaker Setup menu appears Speaker Conﬁg menu appearCrossover Frequency Use the Up/Down / but Setup menu closesSpeaker Distance Then press the Enter but- tonSpeaker Level Calibration Tons to select 2. Input Setup Input SetupDigital Setup Roll the scroll wheel to selectName of the currently selected Video SetupVideo Setup menu appears DVD in this caseTon Component Video SetupVideo Setup menu appears INPUT1 Select if the video compo- nent is connected to COMSetup, and then press the Enter button Remote SetupChanging the DTR-8.4’s Remote Control ID Specifying the Location of an IR ReceiverChanging the Remote Controller’s Control ID Specifying the TV System Australian model onlyDTR-8.4En.book Page 50 Thursday, October 16, 2003 1109 AM Basic Operation Selecting the Source AV ComponentStart playback on the selected AV component Setting the Display Brightness Muting the DTR-8.4 remote controller onlyUsing the Sleep Timer remote controller only Using HeadphonesInput source you want to set Setting the Input Signal FormatFixing the Digital Input Format Press the Audio SEL buttonUsing the Tuner Tuning into Radio StationsPresetting Radio Stations Ory button, press the FM Mode Selecting Presets Deleting PresetsTo select the presets Press the Tuner input selectorListening Modes About the Listening ModesDSP Modes DTS Selecting Listening Modes DTS/DTS-ES Discrete/DTS-ES Matrix Using the Digital Surround ModesDolby Digital/Dolby Digital EX THX Surround EX Dolby DigitalDisplay Indicators & Source Info Displaying Source InformationAdjusting the Volume of Individual Speakers Using the Re-EQ functionUsing the Late Night function Dolby Digital only Advanced Operation Using the Multichannel Input Setting the Multichannel Input Main menu appearsAdvanced Operation Selecting the Multichannel InputRecording Recording a Separate Input SourceRecording the Current Input Source Recording Separate AV Sources Advanced Setup Tons to select 3. Audio Adjust Advanced SetupAudio Adjust Functions Assigning the a & B 12V Trigger OutputsSurround Speakers DelayTone Control Sound EffectTheater-Dimensional LFE LevelMono Surround THXSetting Preferences Volume SetupHeadphones Level Naming Presets & Input Sources OSD SetupOSD Position Repeat until you’ve Using IntelliVolumeIntelliVolume menu appears Entered all 10 charactersInternet Radio Net-TuneAbout Net-Tune Net-TuneNet-Tune Networking Your DTR-8.4Tons to select Genres, Location Using Internet RadioPress the Enter button Or LanguagePresetting Internet Radio Stations Selecting Internet Radio PresetsDeleting Internet Radio Presets Playing network audio server Tracks Selecting Items by Letter Playing Net-Tune Tracks RandomlyPlaying Net-Tune Tracks Repeatedly Music Server Settings Network Setup menu appears 2Network SettingsPress the scroll wheel, and then Press the Setup button IP Address menu is shown hereIP Address Proxy SetupClient Setup Mac AddressUsing Only Speakers in Zone Connecting ZoneUsing a Receiver/Integrated Amp in Zone Using a Power Amp in ZoneUsing a Multiroom Kit with a Cabinet Using the Remote Control in ZoneUsing the 12V Trigger Using a Multiroom Kit with ZoneZone2, and then press Setting the Surr Back/Zone 2 OutputsTons to select 2. Surr Back Surr Back/ Zone2 menu appearsControlling Zone Using the Remote Controller with Other Components Entering a Remote Control CodeRemote Control Codes for an Integra/ Onkyo DVD Player Using the Remote Controller with Other Components Remote Control CodesDTR-8.4En.book Page 90 Thursday, October 16, 2003 1109 AM Controlling a Satellite Receiver Controlling a VCR Following buttons control the DTR-8.4Controlling a TV Controlling a Cable ReceiverLearning Commands from Another Remote Controller Using Macros Making MacrosRunning Macros Naming MacrosReordering the Remote Controller Modes Editing Remote Controller ModesAdding New Remote Controller Modes MODE, and then pressDeleting Remote Controller Modes Assigning Remote Controller ModesResetting the Remote Controller Troubleshooting Troubleshooting Can’t access Internet radio or the network audio server? Can’t learn commands from other remote con- trollers?Surr Back speaker setting doesn’t appear? Can’t control other components?Can’t use an audio adjust function? Sound changes when I connect my head- phones?Can’t change a setting? Hardware Setup does not appear in the menu?General SpeciﬁcationsAmplifier Section Video Section104 DTR-8.4 Enjoying Home TheaterConnecting Your Speakers Connecting the Speaker CablesUsing Composite Video or S-Video Connecting Your TV & DVD PlayerConnecting a TV Turning On the DTR-8.4Selecting Listening Modes Adjust the volumePlaying a DVD Select the DVD input sourceDTR-8.4/7.4 Net-Tune Quick Start Guide Networking the DTR-8.4/7.4