Windsor QTFSG, QTFSD manual Hydraulic Schematic Hydraulic Troubleshooting, Problem Cause Solution

Page 32

HYDRAULIC SCHEMATIC

HYDRAULIC TROUBLESHOOTING

PROBLEM

CAUSE

SOLUTION

 

 

 

Hopper will not lift

Loss of power to rocker

Key switch must be on check circuit breaker

switch

 

 

 

Low hydraulic fluid

Add hydraulic fluid

 

Hopper overloaded

Empty hopper

 

Rocker switch failure

Test – replace switch

 

Speed control orifice

Clean or replace orifice (located behind the lower

 

plugged

cylinder fitting)

 

Pump solenoid failure

Replace pump solenoid

 

Check valve failure

Replace check valve or solenoid

 

Lift cylinder failure

Replace cylinder seals

 

Gear pump failure

Replace pump or pump motor

Hopper will not lower

Loss of power to rocker

Key switch must be on, check circuit breaker

switch

 

 

 

Rocker switch failure

Test – replace switch

 

Speed control orifice

Clean or replace orifice (located behind the lower

 

plugged

cylinder fitting)

 

Check valve failure

Replace check valve or solenoid

4-15

QTFSG/QTFSD 98349 05/15/03

 

Image 32
Contents Floor Sweeper Model Tracer FSOverview Machine Data LOGYour Dealer Table of Contents HOW to USE this Manual ModelImportant Safety Instructions Read ALL Instructions Before Using this MachineHazard Intensity Level Hazard Intensity LevelSafety Label Location Safety Label Location Technical Specifications DIMENSION/CAPACITYControls Special NotesControls Filter Shaker Switch Directional Control PedalBrake Pedal Parking Brake LeverHopper Door Switch Hopper Lift SwitchHopper Safety ARM Engine Temperature LightKEY Switch Choke GAS onlyCircuit Breakers Horn PADOperations Before Operating the FSStarting the Machine To SweepTo Engage the Hopper Safety ARM Stopping the MachineStoring the Machine Dumping the HopperTo Disengage the Hopper Safety ARM Towing or Pushing MachineMachine Jacking To Jack UP MachineMaintenance Hydraulic FluidHydraulic Fluid Reservoir Hydraulic PumpRefer to the Electrical Control Group in the Parts section Hydraulic FilterDirectional Control System To Install the Main Broom To Remove the Main BroomMain Broom Pattern To 1-1/2 25.4 to 38.1mm Checking and Adjusting the Main Broom PatternMain Broom Adjustment Knob To Install the Side Broom Adjusting the Side BroomRaised hopper may fall. Engage hopper safety arm To Remove the Side BroomAdjusting the Jackshaft Belt Transmission Jackshaft BeltTo Replace Belt Transmission BeltTo Align Belt Replacing and Adjusting Main Broom BeltReplacing and Adjusting the Vacuum Impeller Belt Replacing and Adjusting Differential Impeller BeltTo Realign Drive ChainReplacing the Right Broom Door Skirt Replacing and Adjusting the Drive Wheel ChainsAdjusting the Right Broom Door Skirt Adjusting the Left Broom Skirt Adjusting the Rear Broom SkirtReplacing the Left Broom Skirt Recirculation SkirtAdjusting the Hopper Side Seals Hopper SealsReplacing the Hopper Seals Hopper LIP SkirtsHopper Door Seals Replacing Door SealsHopper Hopper Dust FilterTo Adjust the Brakes Raised hopper arm may fall. Engage hopper safety armAIR Brakes Refer to the Brake Group in the Parts sectionBattery Battery MaintenanceHydraulic Schematic Hydraulic Troubleshooting Problem Cause SolutionHopper will not lift Hopper will not lowerNo propelling Machine moves withoutPressing foot pedal Full speed onlyMachine Troubleshooting Excessive dustingPoor sweeping Machine travels slowlyService Schedule Maintenance Daily Weekly 50HRS