Windsor QTFSG, QTFSD manual Hazard Intensity Level

Page 6

HAZARD INTENSITY LEVEL

The following symbols are used throughout this guide as indicated in their descriptions:

HAZARD INTENSITY LEVEL

There are three levels of hazard intensity identified by signal words -WARNINGand CAUTION and FOR SAFETY . The level of hazard intensity is determined by the following definitions:

! WARNING

WARNING - Hazards or unsafe practices which COULD result in severe personal injury or death.

!

CAUTION - Hazards or unsafe practices which could result in minor personal injury or product or property damage.

FOR SAFETY: To identify actions which must be followed for safe operation or equipment.

Report machine damage or faulty operation immediately. Do not use the machine if it is not in proper operating condition. Following is information that signals some potentially dangerous conditions to the operator or the equipment. Read this information carefully. Know when these conditions can exist. Locate all safety devices on the machine. Please take the necessary steps to train the machine operating personnel.

FOR SAFETY

DO NOT OPERATE MACHINE:

Unless Trained and Authorized.

Unless Operation Guide is Read and understood.

In Flammable or Explosive areas.

In areas with possible falling objects.

WHEN SERVICING MACHINE:

Avoid moving parts. Do not wear loose clothing; jackets, shirts, or sleeves when working on the machine. Use Windsor approved replacement parts.

! WARNING

Batteries emit hydrogen gas. Explosion or fire can result. Keep sparks and open flame away. Keep sparks and flames away from the battery. Do not smoke around battery.

!

Hazardous voltage. Shock can result. Disconnect battery before working on machine. Only qualified personnel should work inside machine. Always wear eye protection and protective clothing when working on or near battery. Avoid skin contact with the acid contained in the battery.

! WARNING

Never allow metal to lie across battery tops.

! WARNING

Flammable materials or reactive metals can cause explosion or fire. Do not sweep these materials.

! WARNING

Engine emits toxic gases. Severe respiratory damage or asphyxiation can results. Provide adequate ventilation. Consult with your regulatory agency for exposure limits. Keep engine properly tuned.

! WARNING

Machine can emit excessive noise. Consult with your regulatory agency for exposure limits. Hearing loss can result. Wear hearing protection.

! WARNING

Lift arm pinch points. Keep clear of hopper lift arm. Raised hopper may fall. Engage hopper safety arm.

! WARNING

Moving belts. Keep away.

2-2

QTFSG/QTFSD 98349 05/15/03

 

Image 6
Contents Floor Sweeper Model Tracer FSMachine Data LOG Your DealerOverview Table of Contents HOW to USE this Manual ModelImportant Safety Instructions Read ALL Instructions Before Using this MachineHazard Intensity Level Hazard Intensity LevelSafety Label Location Safety Label Location Technical Specifications DIMENSION/CAPACITYControls Special NotesControls Brake Pedal Filter Shaker SwitchDirectional Control Pedal Parking Brake LeverHopper Safety ARM Hopper Door SwitchHopper Lift Switch Engine Temperature LightCircuit Breakers KEY SwitchChoke GAS only Horn PADStarting the Machine OperationsBefore Operating the FS To SweepStoring the Machine To Engage the Hopper Safety ARMStopping the Machine Dumping the HopperMachine Jacking To Disengage the Hopper Safety ARMTowing or Pushing Machine To Jack UP MachineHydraulic Fluid Reservoir MaintenanceHydraulic Fluid Hydraulic PumpHydraulic Filter Directional Control SystemRefer to the Electrical Control Group in the Parts section To Install the Main Broom To Remove the Main BroomChecking and Adjusting the Main Broom Pattern Main Broom Adjustment KnobMain Broom Pattern To 1-1/2 25.4 to 38.1mm Raised hopper may fall. Engage hopper safety arm To Install the Side BroomAdjusting the Side Broom To Remove the Side BroomTo Replace Belt Adjusting the Jackshaft BeltTransmission Jackshaft Belt Transmission BeltReplacing and Adjusting Main Broom Belt Replacing and Adjusting the Vacuum Impeller BeltTo Align Belt To Realign Replacing and Adjusting DifferentialImpeller Belt Drive ChainReplacing and Adjusting the Drive Wheel Chains Adjusting the Right Broom Door SkirtReplacing the Right Broom Door Skirt Replacing the Left Broom Skirt Adjusting the Left Broom SkirtAdjusting the Rear Broom Skirt Recirculation SkirtReplacing the Hopper Seals Adjusting the Hopper Side SealsHopper Seals Hopper LIP SkirtsHopper Hopper Door SealsReplacing Door Seals Hopper Dust FilterAIR To Adjust the BrakesRaised hopper arm may fall. Engage hopper safety arm Brakes Refer to the Brake Group in the Parts sectionBattery Battery MaintenanceHopper will not lift Hydraulic Schematic Hydraulic TroubleshootingProblem Cause Solution Hopper will not lowerPressing foot pedal No propellingMachine moves without Full speed onlyPoor sweeping Machine TroubleshootingExcessive dusting Machine travels slowlyService Schedule Maintenance Daily Weekly 50HRS