Windsor QTFSG Machine Troubleshooting, Excessive dusting, Poor sweeping, Machine travels slowly

Page 34

MACHINE TROUBLESHOOTING

PROBLEM.

CAUSE

SOLUTION

 

 

 

Excessive dusting

Dust skirts and seals worn,

Replace or adjust skirts or seals.

 

damaged, not adjusted

 

 

properly

 

 

Dust filter clogged or

Shake and clean or replace filter.

 

damaged

 

 

Vacuum hose damaged

Replace vacuum hose.

 

Vacuum fan not operated

Belt loose, broken or off pulley.

Poor sweeping

Broom bristles worn

Replace brooms.

performance

 

 

 

Brooms not adjusted

Adjust brooms.

 

properly.

 

 

Debris caught in broom

Free mechanism of debris.

 

drive mechanism.

 

 

Main broom drive failure

Belt loose, broken or off pulley.

 

Side broom drive failure

Check circuit breaker. Check side broom motor

 

 

circuit.

 

Hopper dump door closed

Open dump door.

 

Hopper full

Empty hopper.

 

Hopper floor skirts worn,

Replace skirts.

 

damaged

 

Machine travels slowly

Parking brake set

Release parking brake.

or not at all

 

 

 

Towing valve activated.

Release towing valve.

 

Linkage broken or not

Inspect and adjust or repair.

 

properly adjusted

 

 

Transmission drive belt

Inspect and repair.

 

slipping or broken

 

 

Main engine drive belt

Inspect and repair.

 

failure

 

 

Differential drive chain

Inspect and repair.

 

failure.

 

4-17

QTFSG/QTFSD 98349 05/15/03

Image 34
Contents Floor Sweeper Model Tracer FSYour Dealer Machine Data LOGOverview Table of Contents HOW to USE this Manual ModelImportant Safety Instructions Read ALL Instructions Before Using this MachineHazard Intensity Level Hazard Intensity LevelSafety Label Location Safety Label Location Technical Specifications DIMENSION/CAPACITYControls Special NotesControls Brake Pedal Filter Shaker SwitchDirectional Control Pedal Parking Brake LeverHopper Safety ARM Hopper Door SwitchHopper Lift Switch Engine Temperature LightCircuit Breakers KEY SwitchChoke GAS only Horn PADStarting the Machine OperationsBefore Operating the FS To SweepStoring the Machine To Engage the Hopper Safety ARMStopping the Machine Dumping the HopperMachine Jacking To Disengage the Hopper Safety ARMTowing or Pushing Machine To Jack UP MachineHydraulic Fluid Reservoir MaintenanceHydraulic Fluid Hydraulic PumpDirectional Control System Hydraulic FilterRefer to the Electrical Control Group in the Parts section To Install the Main Broom To Remove the Main BroomMain Broom Adjustment Knob Checking and Adjusting the Main Broom PatternMain Broom Pattern To 1-1/2 25.4 to 38.1mm Raised hopper may fall. Engage hopper safety arm To Install the Side BroomAdjusting the Side Broom To Remove the Side BroomTo Replace Belt Adjusting the Jackshaft BeltTransmission Jackshaft Belt Transmission BeltReplacing and Adjusting the Vacuum Impeller Belt Replacing and Adjusting Main Broom BeltTo Align Belt To Realign Replacing and Adjusting DifferentialImpeller Belt Drive ChainAdjusting the Right Broom Door Skirt Replacing and Adjusting the Drive Wheel ChainsReplacing the Right Broom Door Skirt Replacing the Left Broom Skirt Adjusting the Left Broom SkirtAdjusting the Rear Broom Skirt Recirculation SkirtReplacing the Hopper Seals Adjusting the Hopper Side SealsHopper Seals Hopper LIP SkirtsHopper Hopper Door SealsReplacing Door Seals Hopper Dust FilterAIR To Adjust the BrakesRaised hopper arm may fall. Engage hopper safety arm Brakes Refer to the Brake Group in the Parts sectionBattery Battery MaintenanceHopper will not lift Hydraulic Schematic Hydraulic TroubleshootingProblem Cause Solution Hopper will not lowerPressing foot pedal No propellingMachine moves without Full speed onlyPoor sweeping Machine TroubleshootingExcessive dusting Machine travels slowlyService Schedule Maintenance Daily Weekly 50HRS