Wayne-Dalton 3982 installation instructions Pre-OperationInstallation, Wall Station Installation

Page 15

Pre-Operation Installation

Pre-Operation Installation

Step 15: Wall Station Installation

Locate a convenient place to mount wall station within sight of the garage door. To keep wall station out of the reach of children, measure at least ﬁve feet up from the ﬂoor and secure wall station base into wood wall fram- ing using (2) phillips head screws. Use 2 of 3 holes that best align with wood framing. Use anchors (not included) when fastening to drywall or concrete.

CAUTION: Over tightening screws into wood could deform plastic base and interfere with circuit board snaps.

NOTE: Pilot drill mounting holes using a 3/32” (3mm) bit.

Insert bottom of circuit board behind bottom snap of wall station base. Pivot circuit board up and snap into place. For best results, press on circuit board between battery terminals.

Insert battery onto circuit board being careful to match

(+)positive battery marking with (+) circuit board marking. Align wall station cover/button assembly with base. Press cover assembly over base until cover

BASE

COVER

ASSEMBLY

snaps into place. A uniform seam between the cover and base indicates a proper installation.

Apply wall station reference label and entrapment label in a convenient location next to the wall station.

(2)PHILLIPS HEAD SCREWS

ALTERNATE SCREW LOCATION

CIRCUIT

BOARD

BOTTOM

SNAP

BATTERY TERMINALS

PRESS HERE

WALL STATION

REFERENCE LABEL

ENTRAPMENT

LABEL

15

Image 15

Contents Model 3982 idrive Extension Spring Kit Important NoticeFCC Regulatory Information Table of ContentsSystem Requirements FCC and IC StatementINSTALLATION AND USE INSTALLATION AND USEHardware Kit: 3982 idrive Extension Spring Kit idrive Hardware Kit idrive Package ContentsTools Needed Available Accessories: For idriveStep 2: Remove Front Sheave idrive Retro-ﬁtInstallationExtension idrive Installation Step 1: Extension Spring Reliefshown in step Step 4: Flag Bracket InstallationStep 4A: Track Width Conformation NOTE: In some instances theredrums until instructed to do so Step 5: Cable Drum InstallationStep 6 Bottom Bracket Lifting Cables NOTE Do not remove shrink wrap from cableStep 7: Drum Wrap Installation Step 8 Extension Spring Counterbalancewrapped oppositely on the drum JURY DO NOT PLACE FINGERS OR HAND Step 9: Safety Cable InstallationStep 10 Lower the Door WARNING TO AVOID SEVERE INNOTE: Do not force the opener onto Step 11: idrive Opener/Torque Tube AssemblyNOTE Hold the opener by the main body. Do not hold by the motorStep 13: Secure idrive Opener and Owner’s Manual Step 14: Disconnect Installationtion be pilot drilled using 1/8” drill bit NOTE: It is recommended that 1/4” lag screw locaStep 15: Wall Station Installation Pre-OperationInstallationSwitch Settings Light Fixture Jumper Settings: OpenerStep 16 Multi-Opener/LightFixture Programming CEILING MOUNTING Step 17: Light Fixture InstallationLight Fixture Installation Continued power back on at fuse boxWALL MOUNTING Step 18: Photoelectric Safety Sensor Installation NOTE: If wires must be lengthened or spliced intonectors Installation Continued Photoelectric Safety Sensor#6 X 7/8 WOOD SCREWS POWER CORD FEMALE END OPENER Step 19: Power Connection Standard WiringCONVENIENT POWER OUTLET LIGHT FIXTURE POWER OUTLET RECEPTACLEStep 20 Power Connection Permanent Wiring Option Step 21 Securing the Opener Step 22: Photoelectric Safety Sensor AlignmentWall Station Programming Changing the wall station’s security codeStep 24 Install Routine MOTOR OPERATED POSITIONUP/DOWN BUTTON PROFILE BUTTON Step 25: Detent Adjustment if required Step 26: Lock Arm InstallationStep 27: Custom Settings Step 29: Contact Obstruction Test Step 28 Photoelectric Obstruction Sensor TestTRANSMITTER PROGRAMMING Step 30: Transmitter Security CodeChange and Programming CHANGING THE TRANSMITTER’S SECURITY CODEPROGRAMMING Training HomeLink Unit Teaching Power UnitStep 31: Programming HomeLink to idrive per StepTransmitter Operation Important Safety Instructions8.SAVE THESE INSTRUCTIONS OperationWall Station Operation service person immediatelyManual Door Operation Emergency Disconnect MOTOR DOWN POSITION DOOR LOCKEDDISCONNECTED, MOTOR UP POSITION NOTE: Dispose of dead batteries properly MaintenanceMonthly Maintenance Battery replacementCORRECTIVE ACTION TroubleshootingSYMPTOM PROBABLE CAUSESYMPTOM Troubleshooting continuedLock Arm Troubleshooting SYMPTOMFor quick answers and helpful advise, call Wayne-DaltonCustomer ServiceLIFETIME LIMITED WARRANTY Questions??