Wayne-Dalton 3982 Power Connection Standard Wiring, Plastic Clips Plug Into Nearest

Page 21

Step 19: Power Connection (Standard Wiring)

Step 19: Power Connection (Standard Wiring)

Plug the female end of power cord into the inlet connector on the right side of opener. Plug the other end of the opener power cord into the nearest convenient power receptacle. (If the power cord is not long enough to reach the closest receptacle, the idrive™ Powercord Extender kit is available, otherwise contact a service person for further options.) As soon as power is applied to the opener, the light ﬁxture will light up. If the light ﬁxture does not light, adjust the receiver module alignment. Unplug, then plug back in the power cord. Repeat this process until the light comes on. Ensure there is no obstruction between the opener and the light ﬁxture. Refer to Step 17: Light Fixture Installation for the alignment procedure.

Excess power cord length must be routed and contained safely away from any moving members.

NOTE: Do not permanently attach power cord to building! Use only the ﬂexible plastic clips supplied with the opener

PLASTIC CLIPS

PLUG INTO NEAREST

CONVENIENT POWER OUTLET

WARNING TO REDUCE THE RISK OF ELECTRICAL SHOCK, THIS EQUIPMENT HAS A GROUNDING TYPE PLUG, THAT HAS A THIRD (GROUNDING) PIN. THIS PLUG WILL ONLY FIT INTO A GROUNDING TYPE OUTLET. IF THE PLUG DOES NOT FIT INTO THE OUTLET, CON- TACTA QUALIFIED ELECTRICIAN TO INSTALL THE PROPER OUTLET. DO NOT CHANGE THE PLUG IN ANY WAY.

LIGHT FIXTURE

POWER OUTLET

RECEPTACLE

#6 X 7/8 WOOD SCREWS

POWER CORD

FEMALE END

OPENER

POWER CORD

DISCONNECT

CABLE

NO INTERFERENCE BETWEEN POWER CORD AND DISCONNECT CABLE

21

Image 21

Contents Model 3982 idrive Extension Spring Kit Important NoticeSystem Requirements Table of ContentsFCC and IC Statement FCC Regulatory InformationINSTALLATION AND USE INSTALLATION AND USEHardware Kit: 3982 idrive Extension Spring Kit idrive Hardware Kit idrive Package ContentsTools Needed Available Accessories: For idriveExtension idrive Installation idrive Retro-ﬁtInstallationStep 1: Extension Spring Relief Step 2: Remove Front SheaveStep 4A: Track Width Conformation Step 4: Flag Bracket InstallationNOTE: In some instances there shown in stepStep 6 Bottom Bracket Lifting Cables Step 5: Cable Drum InstallationNOTE Do not remove shrink wrap from cable drums until instructed to do soStep 7: Drum Wrap Installation Step 8 Extension Spring Counterbalancewrapped oppositely on the drum Step 10 Lower the Door Step 9: Safety Cable InstallationWARNING TO AVOID SEVERE IN JURY DO NOT PLACE FINGERS OR HANDNOTE Hold the opener by the main Step 11: idrive Opener/Torque Tube Assemblybody. Do not hold by the motor NOTE: Do not force the opener ontoStep 13: Secure idrive Opener tion be pilot drilled using 1/8” drill bit Step 14: Disconnect InstallationNOTE: It is recommended that 1/4” lag screw loca and Owner’s ManualStep 15: Wall Station Installation Pre-OperationInstallationSwitch Settings Light Fixture Jumper Settings: OpenerStep 16 Multi-Opener/LightFixture Programming CEILING MOUNTING Step 17: Light Fixture InstallationLight Fixture Installation Continued power back on at fuse boxWALL MOUNTING Step 18: Photoelectric Safety Sensor Installation NOTE: If wires must be lengthened or spliced intonectors Installation Continued Photoelectric Safety SensorCONVENIENT POWER OUTLET Step 19: Power Connection Standard WiringLIGHT FIXTURE POWER OUTLET RECEPTACLE #6 X 7/8 WOOD SCREWS POWER CORD FEMALE END OPENERStep 20 Power Connection Permanent Wiring Option Step 21 Securing the Opener Step 22: Photoelectric Safety Sensor AlignmentWall Station Programming Changing the wall station’s security codeStep 24 Install Routine MOTOR OPERATED POSITIONUP/DOWN BUTTON PROFILE BUTTON Step 25: Detent Adjustment if required Step 26: Lock Arm InstallationStep 27: Custom Settings Step 29: Contact Obstruction Test Step 28 Photoelectric Obstruction Sensor TestChange and Programming Step 30: Transmitter Security CodeCHANGING THE TRANSMITTER’S SECURITY CODE TRANSMITTER PROGRAMMINGStep 31: Programming HomeLink to idrive Teaching Power Unitper Step PROGRAMMING Training HomeLink Unit8.SAVE THESE INSTRUCTIONS Important Safety InstructionsOperation Transmitter OperationWall Station Operation service person immediatelyManual Door Operation Emergency Disconnect MOTOR DOWN POSITION DOOR LOCKEDDISCONNECTED, MOTOR UP POSITION Monthly Maintenance MaintenanceBattery replacement NOTE: Dispose of dead batteries properlySYMPTOM TroubleshootingPROBABLE CAUSE CORRECTIVE ACTIONLock Arm Troubleshooting Troubleshooting continuedSYMPTOM SYMPTOMLIFETIME LIMITED WARRANTY Wayne-DaltonCustomer ServiceQuestions?? For quick answers and helpful advise, call