Wayne-Dalton installation instructions Hardware Kit: 3982 idrive Extension Spring Kit

Page 4
Hardware Kit: 3982 idrive™ Extension Spring Kit

Package Contents: 3982 idrive™ Extension Spring Kit

 

RH.

RH.

 

LH.

LH.

 

 

Drum Wrap Set

RH.

 

 

LH.

 

 

Flag Brackets

Cable/Drum

 

 

Assembly

 

(3) Cam Tubes

Photoelectric Safety Sensors

 

W/Hardware

Owners Manual

Hardware Kit: 3982 idrive™ Extension Spring Kit

Cable Loop Tool

(2) Drum Shafts

(2) 3-Hole Clip

(2) Large S-Hook

 

 

 

 

(4) spacers

 

 

 

 

(2) 1/4-20 x 9/16”

(2) 1/4-20

(2) 5/16” x 1-5/8” Hex Head Lag Screw

(2) Snap Buttons

Track Bolt

 

 

 

 

Flange Hex Nut

 

 

 

(2) 1/2-13 x 2” Socket Head Cap Screw

(4) 3/8-16 x 3/4” Truss

(4) 3/8-16

Head Bolt

Hex Nut

(2) 1/2-13 Lock Nut

Grease Packet (1)

(4) 1/2” Flat Washer

 

 

 

 

 

4

 

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Important Notice Model 3982 idrive Extension Spring KitTable of Contents System RequirementsFCC and IC Statement FCC Regulatory InformationINSTALLATION AND USE INSTALLATION AND USEHardware Kit: 3982 idrive Extension Spring Kit idrive Package Contents idrive Hardware KitAvailable Accessories: For idrive Tools Neededidrive Retro-fitInstallation Extension idrive InstallationStep 1: Extension Spring Relief Step 2: Remove Front SheaveStep 4: Flag Bracket Installation Step 4A: Track Width ConformationNOTE: In some instances there shown in stepStep 5: Cable Drum Installation Step 6 Bottom Bracket Lifting CablesNOTE Do not remove shrink wrap from cable drums until instructed to do soStep 8 Extension Spring Counterbalance Step 7: Drum Wrap Installationwrapped oppositely on the drum Step 9: Safety Cable Installation Step 10 Lower the DoorWARNING TO AVOID SEVERE IN JURY DO NOT PLACE FINGERS OR HANDStep 11: idrive Opener/Torque Tube Assembly NOTE Hold the opener by the mainbody. Do not hold by the motor NOTE: Do not force the opener ontoStep 13: Secure idrive Opener Step 14: Disconnect Installation tion be pilot drilled using 1/8” drill bitNOTE: It is recommended that 1/4” lag screw loca and Owner’s ManualPre-OperationInstallation Step 15: Wall Station InstallationJumper Settings: Opener Switch Settings Light FixtureStep 16 Multi-Opener/LightFixture Programming Step 17: Light Fixture Installation CEILING MOUNTINGpower back on at fuse box Light Fixture Installation ContinuedWALL MOUNTING NOTE: If wires must be lengthened or spliced into Step 18: Photoelectric Safety Sensor Installationnectors Photoelectric Safety Sensor Installation ContinuedStep 19: Power Connection Standard Wiring CONVENIENT POWER OUTLETLIGHT FIXTURE POWER OUTLET RECEPTACLE #6 X 7/8 WOOD SCREWS POWER CORD FEMALE END OPENERStep 20 Power Connection Permanent Wiring Option Step 22: Photoelectric Safety Sensor Alignment Step 21 Securing the OpenerChanging the wall station’s security code Wall Station ProgrammingMOTOR OPERATED POSITION Step 24 Install RoutineUP/DOWN BUTTON PROFILE BUTTON Step 26: Lock Arm Installation Step 25: Detent Adjustment if requiredStep 27: Custom Settings Step 28 Photoelectric Obstruction Sensor Test Step 29: Contact Obstruction TestStep 30: Transmitter Security Code Change and ProgrammingCHANGING THE TRANSMITTER’S SECURITY CODE TRANSMITTER PROGRAMMINGTeaching Power Unit Step 31: Programming HomeLink to idriveper Step PROGRAMMING Training HomeLink UnitImportant Safety Instructions 8.SAVE THESE INSTRUCTIONSOperation Transmitter Operationservice person immediately Wall Station OperationMOTOR DOWN POSITION DOOR LOCKED Manual Door Operation Emergency DisconnectDISCONNECTED, MOTOR UP POSITION Maintenance Monthly MaintenanceBattery replacement NOTE: Dispose of dead batteries properlyTroubleshooting SYMPTOMPROBABLE CAUSE CORRECTIVE ACTIONTroubleshooting continued Lock Arm TroubleshootingSYMPTOM SYMPTOMWayne-DaltonCustomer Service LIFETIME LIMITED WARRANTYQuestions?? For quick answers and helpful advise, call
Top Page Image Contents