Wayne-Dalton 3982 installation instructions Installation And Use

Page 3
INSTALLATION AND USE

NOTE: This equipment has been tested and found to comply with limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate ra- dio frequency energy and, if not installed and used in accordance with these instruction, may cause harmful interference to radio communication; however, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or televi- sion reception, which can be determined by turning equipment off and on, user is encouraged to try to correct interference by one or more of the following measures: Reorient or relocate receiving antenna. Increase separation between equipment and receiver. Connect equipment into an outlet on a circuit different from that which receiver is connected. Consult your dealer or/and experienced radio/television technician for help. WARNING: Changes or modifi cations to this unit not expressly approved by party responsible for compliance could void user’s authority to operate this equipment.

IMPORTANT SAFETY INSTRUCTIONS FOR IMPORTANT SAFETY INSTRUCTIONS FOR

INSTALLATION AND USE

INSTALLATION AND USE

WARNING: INCORRECT INSTALLATION CAN LEAD TO SEVERE OR FATAL INJURY. FOLLOW INSTRUCTIONS.

READ AND FOLLOW ALL

INSTALLATION INSTRUCTIONS.

Do not connect the opener to a power source until instructed to do so.

Install the entrapment warning label next to the wall station in a prominent location. Install the emergency release marking on or next to the emergency disconnect.

Remove all ropes and remove or make inoperative all locks connected to the garage door before installing the opener.

Do not wear rings, watches or loose clothing when installing or servicing a garage door system.

Wear safety glasses for eye protection when installing or servicing the opener or door.

WARNING: IT IS VITAL FOR THE SAFETY OF PERSONS TO FOLLOW ALL INSTRUCTIONS. SAVE THESE INSTRUCTIONS.

Install only on a properly balanced garage door. An improperly balanced door could cause severe injury. Have a qualified service person make repairs to cables, spring assemblies, and other hardware before installing the opener.

Where possible, install the opener seven feet or more above the floor. Mount emergency release six feet above the floor.

Locate the wall station: (a) within sight of door, (b) at a minimum height of five feet, so small children cannot reach it, and (c) away from all moving parts of the door.

After installing the opener, the door must reverse when it contacts a

1-1/2” high object (or 2 x 4 board laid flat) on the floor.

Installation and wiring must comply with local building and electrical codes. Connect power cord to a properly grounded outlet. Do not remove the ground pin from power cord.

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Model 3982 idrive Extension Spring Kit Important NoticeFCC Regulatory Information Table of ContentsSystem Requirements FCC and IC StatementINSTALLATION AND USE INSTALLATION AND USEHardware Kit: 3982 idrive Extension Spring Kit idrive Hardware Kit idrive Package ContentsTools Needed Available Accessories: For idriveStep 2: Remove Front Sheave idrive Retro-fitInstallationExtension idrive Installation Step 1: Extension Spring Reliefshown in step Step 4: Flag Bracket InstallationStep 4A: Track Width Conformation NOTE: In some instances theredrums until instructed to do so Step 5: Cable Drum InstallationStep 6 Bottom Bracket Lifting Cables NOTE Do not remove shrink wrap from cableStep 7: Drum Wrap Installation Step 8 Extension Spring Counterbalancewrapped oppositely on the drum JURY DO NOT PLACE FINGERS OR HAND Step 9: Safety Cable InstallationStep 10 Lower the Door WARNING TO AVOID SEVERE INNOTE: Do not force the opener onto Step 11: idrive Opener/Torque Tube AssemblyNOTE Hold the opener by the main body. Do not hold by the motorStep 13: Secure idrive Opener and Owner’s Manual Step 14: Disconnect Installationtion be pilot drilled using 1/8” drill bit NOTE: It is recommended that 1/4” lag screw locaStep 15: Wall Station Installation Pre-OperationInstallationSwitch Settings Light Fixture Jumper Settings: OpenerStep 16 Multi-Opener/LightFixture Programming CEILING MOUNTING Step 17: Light Fixture InstallationLight Fixture Installation Continued power back on at fuse boxWALL MOUNTING Step 18: Photoelectric Safety Sensor Installation NOTE: If wires must be lengthened or spliced intonectors Installation Continued Photoelectric Safety Sensor#6 X 7/8 WOOD SCREWS POWER CORD FEMALE END OPENER Step 19: Power Connection Standard WiringCONVENIENT POWER OUTLET LIGHT FIXTURE POWER OUTLET RECEPTACLEStep 20 Power Connection Permanent Wiring Option Step 21 Securing the Opener Step 22: Photoelectric Safety Sensor AlignmentWall Station Programming Changing the wall station’s security codeStep 24 Install Routine MOTOR OPERATED POSITIONUP/DOWN BUTTON PROFILE BUTTON Step 25: Detent Adjustment if required Step 26: Lock Arm InstallationStep 27: Custom Settings Step 29: Contact Obstruction Test Step 28 Photoelectric Obstruction Sensor TestTRANSMITTER PROGRAMMING Step 30: Transmitter Security CodeChange and Programming CHANGING THE TRANSMITTER’S SECURITY CODEPROGRAMMING Training HomeLink Unit Teaching Power UnitStep 31: Programming HomeLink to idrive per StepTransmitter Operation Important Safety Instructions8.SAVE THESE INSTRUCTIONS OperationWall Station Operation service person immediatelyManual Door Operation Emergency Disconnect MOTOR DOWN POSITION DOOR LOCKEDDISCONNECTED, MOTOR UP POSITION NOTE: Dispose of dead batteries properly MaintenanceMonthly Maintenance Battery replacementCORRECTIVE ACTION TroubleshootingSYMPTOM PROBABLE CAUSESYMPTOM Troubleshooting continuedLock Arm Troubleshooting SYMPTOMFor quick answers and helpful advise, call Wayne-DaltonCustomer ServiceLIFETIME LIMITED WARRANTY Questions??
Top Page Image Contents