Wayne-Dalton 3982 installation instructions idrive Package Contents, idrive Hardware Kit

Page 5
idrive™ Package Contents:

idrive™ Package Contents:

6’ Power Cord (1)

Three-button

Opener

Transmitter (2)

 

Wall Station Assembly

 

Support

Wall Station Bracket Light Fixture Assembly

w/ Screw & Diffuser

Reference Label

Lock Arm Assembly

Entrapment Label

Owners Manual

idrive™ Hardware Kit:

1/4 x 1-1/2” Hex Head Lag Screws (4)

Disconnect

“S” Hook (1)

Disconnect Cable (1)

 

Handle (1)

 

 

M5 x .8 x 12 Phillips

Pan Head Screw (1)

(For Lock Arm)

Jumpers (3)

Handle Bracket (1)

1/4 x 2” Hex Head Lag Screws (2)

#6-32 x 3/4” Phillips

 

 

Pan Head Screw (1)

 

(For Light Fixture)

Emergency

Cable Clips (4)

#6 x 7/8” Phillips Pan

#6-20 x 1/2” Phillips Pan

Head PL Screw (1)

Disconnect Label (1)

 

Head Screws (4)

(for disconnect handle)

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Model 3982 idrive Extension Spring Kit Important NoticeSystem Requirements Table of ContentsFCC and IC Statement FCC Regulatory InformationINSTALLATION AND USE INSTALLATION AND USEHardware Kit: 3982 idrive Extension Spring Kit idrive Hardware Kit idrive Package ContentsTools Needed Available Accessories: For idriveExtension idrive Installation idrive Retro-fitInstallationStep 1: Extension Spring Relief Step 2: Remove Front SheaveStep 4A: Track Width Conformation Step 4: Flag Bracket InstallationNOTE: In some instances there shown in stepStep 6 Bottom Bracket Lifting Cables Step 5: Cable Drum InstallationNOTE Do not remove shrink wrap from cable drums until instructed to do sowrapped oppositely on the drum Step 7: Drum Wrap InstallationStep 8 Extension Spring Counterbalance Step 10 Lower the Door Step 9: Safety Cable InstallationWARNING TO AVOID SEVERE IN JURY DO NOT PLACE FINGERS OR HANDNOTE Hold the opener by the main Step 11: idrive Opener/Torque Tube Assemblybody. Do not hold by the motor NOTE: Do not force the opener ontoStep 13: Secure idrive Opener tion be pilot drilled using 1/8” drill bit Step 14: Disconnect InstallationNOTE: It is recommended that 1/4” lag screw loca and Owner’s ManualStep 15: Wall Station Installation Pre-OperationInstallationStep 16 Multi-Opener/LightFixture Programming Switch Settings Light FixtureJumper Settings: Opener CEILING MOUNTING Step 17: Light Fixture InstallationWALL MOUNTING Light Fixture Installation Continuedpower back on at fuse box nectors Step 18: Photoelectric Safety Sensor InstallationNOTE: If wires must be lengthened or spliced into Installation Continued Photoelectric Safety SensorCONVENIENT POWER OUTLET Step 19: Power Connection Standard WiringLIGHT FIXTURE POWER OUTLET RECEPTACLE #6 X 7/8 WOOD SCREWS POWER CORD FEMALE END OPENERStep 20 Power Connection Permanent Wiring Option Step 21 Securing the Opener Step 22: Photoelectric Safety Sensor AlignmentWall Station Programming Changing the wall station’s security codeUP/DOWN BUTTON PROFILE BUTTON Step 24 Install RoutineMOTOR OPERATED POSITION Step 27: Custom Settings Step 25: Detent Adjustment if requiredStep 26: Lock Arm Installation Step 29: Contact Obstruction Test Step 28 Photoelectric Obstruction Sensor TestChange and Programming Step 30: Transmitter Security CodeCHANGING THE TRANSMITTER’S SECURITY CODE TRANSMITTER PROGRAMMINGStep 31: Programming HomeLink to idrive Teaching Power Unitper Step PROGRAMMING Training HomeLink Unit8.SAVE THESE INSTRUCTIONS Important Safety InstructionsOperation Transmitter OperationWall Station Operation service person immediatelyDISCONNECTED, MOTOR UP POSITION Manual Door Operation Emergency DisconnectMOTOR DOWN POSITION DOOR LOCKED Monthly Maintenance MaintenanceBattery replacement NOTE: Dispose of dead batteries properlySYMPTOM TroubleshootingPROBABLE CAUSE CORRECTIVE ACTIONLock Arm Troubleshooting Troubleshooting continuedSYMPTOM SYMPTOMLIFETIME LIMITED WARRANTY Wayne-DaltonCustomer ServiceQuestions?? For quick answers and helpful advise, call
Top Page Image Contents