Wayne-Dalton 3982 Light Fixture Installation Continued, Wall Mounting, power back on at fuse box

Page 18
Light Fixture Installation (Continued)

Light Fixture Installation (Continued)

WALL MOUNTING

Depending on location, the light fixture may need to be adjusted from its packaged position.

When mounting on a wall parallel to the opener, rotate the receiver module inward to a maximum of 90° until the receiver module is best aligned with the sending LED. Mount light to a receptacle and align the receiving module per previous instructions.

NOTE: RECEPTACLE COVER MUST BE INSTALLED IN BETWEEN THE

LIGHT FIXTURE AND THE WALL

LIGHT BULB - 75W

LIGHTMAX. (NOT INCLUDED) FIXTURE SOCKET

#6-32 X 3/4”

PHILLIPS PAN

HEAD SCREW

WALL MOUNTINGDIFFUSER

DUPLEX RE-

CEPTACLE

To mount the light fixture on a wall perpendicular to the opener, leave receiving module in the factory position.

ROTATE 90°

HOLE PLUG

power back on at fuse box. RECEIVING MODULE

Mount the fixture to a receptacle and align receiving module per previous instructions. Insert hole plug into the screw hole.

(IF NECESSARY)

NOTE: For temperature protection, the hole plug must be in place prior to using the light fixture.

Screw in a maximum 75W light bulb into light socket and snap diffuser into light fixture. Turn receptacle

power back on at fuse box.

Final alignment of the light fixture to the opener may be needed once the opener is electrically connected.

18

Image 18
Contents Important Notice Model 3982 idrive Extension Spring KitFCC and IC Statement Table of ContentsSystem Requirements FCC Regulatory InformationINSTALLATION AND USE INSTALLATION AND USEHardware Kit: 3982 idrive Extension Spring Kit idrive Package Contents idrive Hardware KitAvailable Accessories: For idrive Tools NeededStep 1: Extension Spring Relief idrive Retro-fitInstallationExtension idrive Installation Step 2: Remove Front SheaveNOTE: In some instances there Step 4: Flag Bracket InstallationStep 4A: Track Width Conformation shown in stepNOTE Do not remove shrink wrap from cable Step 5: Cable Drum InstallationStep 6 Bottom Bracket Lifting Cables drums until instructed to do soStep 7: Drum Wrap Installation Step 8 Extension Spring Counterbalancewrapped oppositely on the drum WARNING TO AVOID SEVERE IN Step 9: Safety Cable InstallationStep 10 Lower the Door JURY DO NOT PLACE FINGERS OR HANDbody. Do not hold by the motor Step 11: idrive Opener/Torque Tube AssemblyNOTE Hold the opener by the main NOTE: Do not force the opener ontoStep 13: Secure idrive Opener NOTE: It is recommended that 1/4” lag screw loca Step 14: Disconnect Installationtion be pilot drilled using 1/8” drill bit and Owner’s ManualPre-OperationInstallation Step 15: Wall Station InstallationSwitch Settings Light Fixture Jumper Settings: OpenerStep 16 Multi-Opener/LightFixture Programming Step 17: Light Fixture Installation CEILING MOUNTINGLight Fixture Installation Continued power back on at fuse boxWALL MOUNTING Step 18: Photoelectric Safety Sensor Installation NOTE: If wires must be lengthened or spliced intonectors Photoelectric Safety Sensor Installation ContinuedLIGHT FIXTURE POWER OUTLET RECEPTACLE Step 19: Power Connection Standard WiringCONVENIENT POWER OUTLET #6 X 7/8 WOOD SCREWS POWER CORD FEMALE END OPENERStep 20 Power Connection Permanent Wiring Option Step 22: Photoelectric Safety Sensor Alignment Step 21 Securing the OpenerChanging the wall station’s security code Wall Station ProgrammingStep 24 Install Routine MOTOR OPERATED POSITIONUP/DOWN BUTTON PROFILE BUTTON Step 25: Detent Adjustment if required Step 26: Lock Arm InstallationStep 27: Custom Settings Step 28 Photoelectric Obstruction Sensor Test Step 29: Contact Obstruction TestCHANGING THE TRANSMITTER’S SECURITY CODE Step 30: Transmitter Security CodeChange and Programming TRANSMITTER PROGRAMMINGper Step Teaching Power UnitStep 31: Programming HomeLink to idrive PROGRAMMING Training HomeLink UnitOperation Important Safety Instructions8.SAVE THESE INSTRUCTIONS Transmitter Operationservice person immediately Wall Station OperationManual Door Operation Emergency Disconnect MOTOR DOWN POSITION DOOR LOCKEDDISCONNECTED, MOTOR UP POSITION Battery replacement MaintenanceMonthly Maintenance NOTE: Dispose of dead batteries properlyPROBABLE CAUSE TroubleshootingSYMPTOM CORRECTIVE ACTIONSYMPTOM Troubleshooting continuedLock Arm Troubleshooting SYMPTOMQuestions?? Wayne-DaltonCustomer ServiceLIFETIME LIMITED WARRANTY For quick answers and helpful advise, call