Wayne-Dalton 3982 installation instructions Light Fixture Installation, Ceiling Mounting

Page 17
Step 17: Light Fixture Installation

Step 17: Light Fixture Installation

IMPORTANT! The light is turned on and off by an infrared (IR) signal sent from the opener to the light. Therefore, the light must be mounted in a location where it can always “see” the front face of the opener.

Locate a duplex receptacle within line of sight of opener, when the door is in the open position. Disconnect power to the receptacle at the fuse/breaker box before proceeding.

CEILING MOUNTINGManual backgroundWARNING TO REDUCE THE RISK OF ELECTRICAL SHOCK, THIS EQUIPMENT HAS A

GROUNDING TYPE PLUG, THAT HAS A THIRD (GROUNDING) PIN. THIS PLUG WILL ONLY FIT INTO A GROUNDING TYPE OUTLET. IF THE PLUG DOES NOT FIT INTO THE OUTLET, CON- TACT A QUALIFIED ELECTRICIAN TO INSTALL THE PROPER OUTLET. DO NOT CHANGE THE PLUG IN ANY WAY.

Manual backgroundManual backgroundWARNING TO AVOID ELECTRICAL SHOCK, DISCONNECT POWER TO THE RECEP- TACLE AT THE FUSE/BREAKER BOX BEFORE PROCEEDING.

Manual backgroundManual backgroundWARNING DO NOT INSTALL THE LIGHT FIXTURE INTO A RECEPTACLE WITH A METAL FACEPLATE.

NOTE: RECEPTACLE COVER MUST BE INSTALLED IN-BETWEEN THE LIGHT FIXTURE AND THE CEILING

DUPLEX

RECEPTACLE

LIGHT FIXTURE

THUMB

SCREW

ALIGN

Manual background RECEIVING

MODULE

AIM AT

Manual background IR LED

NOTE: Door must clear light fixture when the door is in the open position. There must be no obstruction between the light fixture and the opener for light fixture to work properly.

CEILING MOUNTING

Remove the center screw in the receptacle cover. Hold- ing receptacle cover in place, insert light fixture into the receptacle that has the ground hole farthest from center screw hole. Remove center hole plug from light fixture to expose the screw hole. Secure light fixture to receptacle with a #6-32 x 3/4” phillips pan head screw. Replace hole plug into the screw hole in the light fix- ture. NOTE: For temperature protection, the hole plug must be in place prior to using the light fixture.

HOLE PLUG

75W (MAX)

LIGHT BULB (NOT INCLUDED)

#6-32 X 3/4”

PHILLIPS PAN HEAD SCREW

DIFFUSER

Loosen thumb screw and rotate light fixture’s bottom section to align the receiving module, side to side, with the sending LED on the opener. Re-tighten thumb screw, don’t over tighten. Rotate receiving module to align, up and down, with the sending LED.

Screw a maximum 75W light bulb into light socket and snap diffuser into light fixture. Turn receptacle power back on at fuse/breaker box. The light should blink one time when the power is re-established.

NOTE:An accessory power outlet receptacle (600 Watt Maximum) is provided on the light fixture.

OPENER

SENDING IR LED

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Model 3982 idrive Extension Spring Kit Important NoticeSystem Requirements Table of ContentsFCC and IC Statement FCC Regulatory InformationINSTALLATION AND USE INSTALLATION AND USEHardware Kit: 3982 idrive Extension Spring Kit idrive Hardware Kit idrive Package ContentsTools Needed Available Accessories: For idriveExtension idrive Installation idrive Retro-fitInstallationStep 1: Extension Spring Relief Step 2: Remove Front SheaveStep 4A: Track Width Conformation Step 4: Flag Bracket InstallationNOTE: In some instances there shown in stepStep 6 Bottom Bracket Lifting Cables Step 5: Cable Drum InstallationNOTE Do not remove shrink wrap from cable drums until instructed to do sowrapped oppositely on the drum Step 7: Drum Wrap InstallationStep 8 Extension Spring Counterbalance Step 10 Lower the Door Step 9: Safety Cable InstallationWARNING TO AVOID SEVERE IN JURY DO NOT PLACE FINGERS OR HANDNOTE Hold the opener by the main Step 11: idrive Opener/Torque Tube Assemblybody. Do not hold by the motor NOTE: Do not force the opener ontoStep 13: Secure idrive Opener tion be pilot drilled using 1/8” drill bit Step 14: Disconnect InstallationNOTE: It is recommended that 1/4” lag screw loca and Owner’s ManualStep 15: Wall Station Installation Pre-OperationInstallationStep 16 Multi-Opener/LightFixture Programming Switch Settings Light FixtureJumper Settings: Opener CEILING MOUNTING Step 17: Light Fixture InstallationWALL MOUNTING Light Fixture Installation Continuedpower back on at fuse box nectors Step 18: Photoelectric Safety Sensor InstallationNOTE: If wires must be lengthened or spliced into Installation Continued Photoelectric Safety SensorCONVENIENT POWER OUTLET Step 19: Power Connection Standard WiringLIGHT FIXTURE POWER OUTLET RECEPTACLE #6 X 7/8 WOOD SCREWS POWER CORD FEMALE END OPENERStep 20 Power Connection Permanent Wiring Option Step 21 Securing the Opener Step 22: Photoelectric Safety Sensor AlignmentWall Station Programming Changing the wall station’s security codeUP/DOWN BUTTON PROFILE BUTTON Step 24 Install RoutineMOTOR OPERATED POSITION Step 27: Custom Settings Step 25: Detent Adjustment if requiredStep 26: Lock Arm Installation Step 29: Contact Obstruction Test Step 28 Photoelectric Obstruction Sensor TestChange and Programming Step 30: Transmitter Security CodeCHANGING THE TRANSMITTER’S SECURITY CODE TRANSMITTER PROGRAMMINGStep 31: Programming HomeLink to idrive Teaching Power Unitper Step PROGRAMMING Training HomeLink Unit8.SAVE THESE INSTRUCTIONS Important Safety InstructionsOperation Transmitter OperationWall Station Operation service person immediatelyDISCONNECTED, MOTOR UP POSITION Manual Door Operation Emergency DisconnectMOTOR DOWN POSITION DOOR LOCKED Monthly Maintenance MaintenanceBattery replacement NOTE: Dispose of dead batteries properlySYMPTOM TroubleshootingPROBABLE CAUSE CORRECTIVE ACTIONLock Arm Troubleshooting Troubleshooting continuedSYMPTOM SYMPTOMLIFETIME LIMITED WARRANTY Wayne-DaltonCustomer ServiceQuestions?? For quick answers and helpful advise, call
Top Page Image Contents