Heat & Glo LifeStyle TIARAP-CES, TIARAP-CTO, TIARAP-BK, TIARAP-BR Horizontal Termination, Step

Page 12

F. Horizontal Termination

Type A - Up & Out Installation

TERMINATION CAP

90° ELBOW

CENTER LINE

PIPE LENGTH

WALL THIMBLE

WALL THIMBLE COVER

PIPE LENGTH

Type B - Straight Out Installation

TERMINATION CAP

CENTER LINE

	16-5/8 in.
	16-5/8 in.	WALL THIMBLE
	(42 cm)	WALL THIMBLE
	(42 cm)

WALL THIMBLE COVER

Type C - 45° Elbow in Corner Installation

WALL THIMBLE

45°

ELBOW

2 in. (51mm) CLEARANCE FROM STOVE CORNER TO COMBUSTILE WALL

2 in. (51mm) CLEARANCE FROM STOVE CORNER TO COMBUSTIBLE WALL

Figure 5.3

Step 1.

Determine the desired location of the appliance. Check to ensure that wall studs or roof rafters are not in the way when the venting system is attached. If this is the case, you may want to adjust the location of the appliance.

WARNING

Fire Hazard.

Exhaust Fume Risk.

Impaired Performance of Appliance.

•Ensure vent components are locked together correctly.

•Pipe may separate if not properly joined.

Step 2.

Direct vent pipe is designed with a locking connection. To connect the venting system to the appliance flue outlet, a twist-lock adapter is built into the appliance at the factory. Wall thickness may vary. Remember to include wall thickness in minimum clearances when figuring venting lengths for your installation needs.

Note: Female ends of direct vent pipe/elbows are designed to slide straight onto the male ends of adjacent pipes by orienting the pipe indentations so they match and slide into the entry slots on the male ends, see Figure 5.4. Push the pipe sections completely together, then twist-lock one section clockwise approximately one-quarter turn, until the two sections are fully locked. The female locking lugs may not be visible from the outside. They may be located by examining the inside of the female ends.

Female Locking Lugs

Male Locking Lugs

Figure 5.4

WARNING

Fire Risk. Explosion Risk. Combustion Fume Risk.

Use vent run supports per installation instructions. Connect vent sections per installation instructions.

•Maintain all clearances to combustibles.

•Do NOT allow vent to sag below connection point to appliance.

•Maintain speciﬁed slope (if required).

Improper support may allow vent to sag or separate.

Page 12

Heat & Glo · Tiara Petite B · 7026-101K

August 1, 2008

Image 12

Contents Installation and Operation What to do if you smell gasHot glass will cause burns Congratulations Location Hang tag attached to rear of applianceTable of Contents 1Listing and Code Approvals Requirements for the Commonwealth of Massachusetts Design & Installation Considerations Getting StartedTools and Supplies Needed Inspect Appliance & ComponentsAppliance Location and Clearances Selecting Appliance LocationClearances to Combustibles 4Termination Locations Vent Termination Minimum ClearancesAlcove Applications Vent Information Venting ComponentsUse of Elbows Measuring StandardsHow to Use the Vent Graph Venting GuidelinesHorizontal Termination Step203mm Vinyl Siding Vertical Termination Direct Vent PipeCeiling Joists Framing 2 in mm Long Wood Screws Twist-lock the vent cap and seal Cathedral Ceiling Level Cathedral Ceiling Support BoxClass a Metal Chimney Type C Up & Out Installation Type a & B Co-Axial to Co-LinearExisting Masonry Chimney Type D Hearth MountCut and bend flashing as needed to fit Sealant adhesive Flex Liner Flex Coupler Sheet Metal Screws Installing Slim Line Trim Ring and Heat Shield Slim Line Wall ThimbleAssembling Slim Line Trim Ring and Heat Shield NextFIG. C Minimum Clearance Wire clip Gas InformationFuel Conversions Converting to LP GasValve Regulator Replacement Screws Rubber Gasket Identification Label FGas Pressures Gas ConnectionHigh Altitude Installations Recommendation for Wire Connecting to the ApplianceStanding Pilot Ignition System Wiring Wire Size Max. LengthIgnition Module Access and Battery Replacement To access the moduleAppliance Setup Remove Shipping Materials Flue Restrictor InstallationLeg Leveling System Intake Air Shutter Adjustment Intake Damper Operation Positioning the LogsAccessories Mineral WoolBlower Installation KIT ContentsAugust 1 Heat & Glo · Tiara Petite B · 7026-101K 19 Complete Assembly Warming Shelves Installation Glass ReplacementOperating Instructions Before Lighting ApplianceControls For Your Safety Read Before Lighting Lighting ApplianceFrequently Asked Questions Initial Break-in ProcedureAfter Appliance is Lit Troubleshooting Symptom Possible Cause Corrective ActionBe Placed in this Opening Maintaining and Servicing Appliance After servicingMaintenance Tasks Inspect Necessary. USE Caution When CLEANING/HANDLING Ceramic BurnerAppliance Dimension Diagram Reference MaterialsVent Components Diagram SL-D Series Vent ComponentsVent Components List HHT SL-PTermination Caps & Kits Tiara Petite B DescriptionService Parts List cont’d. Tiara Petite B Tiara Petite B Cast Parts Individual Pieces Accessories Service and Maintenance Log Date of Service Performed By Description of ServiceWarranty Policy Limited Lifetime Warranty Heat & GLO GAS Appliance ProductsTiara Petite B Contact InformationDealer Telephone