Gas-Fired Products 150, N7/L7, 100, 40, 175, 200 manual Minimum Clearances to Combustibles

Page 5

4.0) MINIMUM CLEARANCES TO COMBUSTIBLES

Combustible material must be located outside the clearance dimensions listed.

Failure to do so may result in death, serious injury or property damage.

Minimum clearances to combustibles shall be measured from the outer surfaces as shown in the following diagram:

End

* Ceiling

End

Ceiling

Front

Side

Side

Rear

Below

Below

Horizontal45° Angle (Maximum)

MINIMUM CLEARANCES TO COMBUSTIBLES

 

 

 

 

 

Angle Mounted at

 

 

Mounted Horizontally

 

45º

Model No.

Sides

Ceiling*

Below

Ends

45º Front

45º Rear

PTS/PTU 40/25

27”

6”

40”

30”

48”

12”

 

 

 

 

 

 

 

PTS/PTU 50/30

27”

6”

40”

30”

48”

12”

 

 

 

 

 

 

 

PTS/PTU 75/50

27”

6”

60”

30”

48”

12”

 

 

 

 

 

 

 

PTS/PTU 100/65

66”

6”

88” **

40”

66”

20”

 

 

 

 

 

 

 

PTS/PTU 125/80

66”

6”

101” **

40”

66”

20”

 

 

 

 

 

 

 

PTS/PTU 150/100

84”

6”

106” **

48”

84”

24”

 

 

 

 

 

 

 

PTS/PTU 175/110

84”

6”

106” **

48”

84”

24”

 

 

 

 

 

 

 

PTS/PTU 200/125

84”

6”

106” **

48”

84”

24”

 

 

 

 

 

 

 

*When used indirect vented, minimum clearance for CEILING must be: 12” for PTS/PTU 50-75 and 18” for PTS/PTU 100-200. If optional corner and u-bend reflectors are not used, the clearance must be 18”.

**Maximum clearance below reduces to 72” once you are 20ft. downstream from the control box.

WARNING: Certain materials or objects, when stored under the heater, will be subjected to radiant heat and could be seriously damaged. Observe the Minimum Clearances to Combustibles listed in the manual and on the heater at all times.

NOTE: The clearances specified above must be maintained to combustibles and other materials that may be damaged by temperatures 90ºF above ambient temperature. Clearances to combustibles are posted on the control box. In areas used for storage of combustible materials where they may be stacked below the heater, NFPA54 requires that the installer must post signs that will “specify the maximum permissible stacking height to maintain the required clearances from the heater to combustibles.” Space-Ray recommends posting these signs adjacent to the heater thermostat or other suitable location that will provide enhanced visibility.

 

Form #43343530

–4–

JJuly 08

Image 5
Contents Installation and Operation Instructions Table of Contents Installer Responsibility SafetyInstallation Requirements General InformationHigh Altitude For Canada onlyMinimum Clearances to Combustibles Minimum Clearances to CombustiblesPacking List SpecificationsNatural GAS Burner Package NumbersPTU 40-200 Body Package Descriptions Reflector, 4’ 11 ½’ End Reflector Accessory Package AccessoriesExhaust Hood Package Emitter Length Body Length Model Typical Layouts PTU / PTS SeriesPoisonous GAS and Soot Hazard Typical Assembly LayoutPTS Series Dimensions PTU Series Joining of Tube Sections Heater AssemblyTypical Assembly Overview PTU 40FT Shown Suspension Hazard Typical Suspension MethodsCUT Hazard Assembly of Tube SectionsMIN 8’ MAX 10’ Between Hangers Assembly of Extension SectionInserting Turbulators Ft. Turbulator Sections Adding ReflectorsAdding Optional Corner Reflector PTS only Adding Optional 90º Elbow PTS onlyAdding Optional U-BEND Reflector PTU only Adding 180U-Bend PTU onlyAttaching Burner BOX Assembly Instructions Connecting the Tiss SystemEnd View Angle Mounted Heaters only Do not USE AN Open Flame of ANY Kind to Test for Leaks GAS Connections and RegulationsKEY Dimensions and Components of the GAS Connections Manifold PRESSURE- Combination GAS Valve is Factory SET Instructions for Pressure Test Gauge ConnectionSupply Pressure GAS Control Valve Electrical ConnectionsTH/W Ignition Module Terminal Designations 24VAC/RPS/W GNDLOW Voltage 24V Thermostat Connections Multiple Heaters LOW Voltage 24V Thermostat Connections Single HeaterSingle Heater Venting Vertical Through the Roof VentingSingle Heater Venting Horizontal Through Sidewall #10 Self-Drill Vent Pipe Screws Indirect Venting Unvented Heaters Common Vent DiameterDirect Outside AIR for Combustion AIR for CombustionSide View Lighting and Shutdown InstructionsSequence of Operation Burner Component Locations Electric Shock & Explosion Hazard Cleaning and Maintenance22.0 Troubleshooting GuideForm #43343530 JJuly Replace air switch Restart Troubleshooting Yes Removal of Main Burner and Electrodes Replacing PartsAIR Switch Pressure Check Removal of GAS Valve and Manifold AssemblyTo Check Flame Sensor Circuit Ignition Module DiagnosticsIgnition System Checks Replacement Parts Guide Burner BOX Installation DataLabels/Manual 22c Description Body Components