CPG CPG #2561255 manual Testing the Remote Annunciator

Page 30

Contents

1

2

CPG #2561255

FIRELARM 2500 Operating Manual

7. Press

. All audible and visual indicators on the panel and NAC outputs should operate.

Restore AC power and verify panel is in normal standby condition.

8.Press to enter auto reset mode.

9.Operate each initiating device on all zones. All audible and visual notification appliances should operate. NAC devices pulse the zone number. Power is then removed from the initiating device circuit for approximately 7 seconds. No alarms can be initiated during this test. If the initiating device has not been restored the panel will repeat the test pulse.

10.Operate each initiating device on the supervisory circuit. Observe that all the indications occur as described in section 2.5.12 Supervisory initiating device circuit.

11.Press to exit auto-reset mode. If had been pressed to enable it, press it to disable it.

All the LEDs on the panel except the green AC ON LED should be off. All audible and visual indicators connected to the notification appliance circuit should be off.

12.The supervising station will also be restored to normal (if applicable).

5.2.2Testing the Remote Annunciator

3

1.

Verify that the control panel is in normal standby condition.

2.

Press and hold TEST on the remote annunciator. Verify that all visual and audible indicators on the

 

 

annunciator are operating. Release TEST.

4

3.

Turn the annunciator keyswitch to the on position. Press RESET. Verify that the annunciator displays

 

the reset countdown

5

5.2.3

Testing the Zonal Digital Alarm Communicator Transmitter (ZDACT)

1.

Initiate a signal while the ZDACT is connected to the primary telephone line.

2.Disconnect the primary line from the ZDACT. Verify that the ZDACT trouble signal is indicated on the control panel and that the trouble signal is transmitted to the supervising station.

3.Disconnect the secondary line from the ZDACT. Verify that the ZDACT trouble signal is indicated on the control panel and that the trouble signal is transmitted to the supervising station.

4.Simulate a fault in the primary telephone number. Verify that the ZDACT uses the secondary telephone number to complete the transmission..

5-2

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Operating Manual CPG #2561255 Firelarm 2500 Operating Manual Warranty Overview CPG #2561255 Firelarm 2500 Operating ManualMaintenance System features OverviewGeneral description Housing SpecificationsElectrical specifications ZdactService use NFPA-72 Listings and approvalsCPG #2561255 IRE L ARM 2500 Operating Manual Operation TouchpadPrimary Primary Function Description Contents Silence and reset operation Normal Standby ConditionSupervisory trouble 6 … Initiating circuit alarmNAC trouble / silence Initiating zone troubleAC power conditions Auxiliary power output conditionsBattery power conditions System troubleCPG #2561255 IRE L ARM 2500 Operating Manual Installation Safety message to installersNfpa and UL installation requirements Requirements for Central Station Fire Alarm Systems Installing the cabinet and optional bezelBattery size requirements WiringZonal Digital Alarm Communicator Transmitter optional Zdact Using the Calculation Table TableCurrent Requirements Motherboard Device Wiring Diagram Notification Appliance Circuits ConnectionsCPG #2561255 IRE L ARM 2500 Operating Manual 1 B1 Strobe device Configuration and ProgrammingSelecting connected device options DIP switches 2 B1 Temporal patternProgram configuration of the panel Setup ZONES? Order of charactersZdact configuration Setup ZDACT?AC Delay HR Password settings Number KeysInspection and Test procedure MaintenanceAuto Reset feature One-man test Testing the control panelTesting the Remote Annunciator Remote Annunciator with Liquid Crystal Display 2500-RALCD Appendix A. Optional AccessoriesKey Function Control When Active Electrical ConnectionsZonal Digital Alarm Communicator Transmitter 2500-ZDACT Figure A-2. Zdact MountingStyle Z Class a Module for NAC circuits CAM Transient Protected Built in 5.1K END of Line ResistorMaster Box Module Model MBM Figure A-5. MBMInstallation MBMCPG #2561255 IRE L ARM 2500 Operating Manual Appendix B. Smoke Detector Compatibility ESL MAX. NO. of Detectors PER Zone isContents Appendix C. NAC Compatibility Contents Base Components Model No Description Stock No Replacement Parts Model No Description Stock NoAppendix D. Ordering Information Options Model No Description Stock NoContents Appendix E. Quick Reference Operating Instructions FireLarm Contents
Top Page Image Contents