Trane PC Workstation Wiring for Building Automation System and Tracker Controllers

Page 55

®

Chapter 6

PC workstation wiring

The Tracker controller connects to a PC workstation with a direct connection cable, an internal modem, or an Ethernet connection.

Verify PC workstation specifications

Verify that the PC conforms to the minimum specifications listed on the insert in the CD jewel case and that the Tracker PC workstation software is installed.

Direct connection to PC workstation

To make an EIA-232 direct connection between the controller and a PC workstation, you need an RJ-12 cable and an adaptor matched to the serial port connector on the PC workstation (Table 10).

Table 10. Cable and adapter specifications for direct connection

Description	Trane part number

RJ-12 interface cable	3591 4260

9-pin female modular adapter	3591 4262

25-pin female modular adapter	3591 4263

The cable and adapter are not shipped with the Tracker controller and must be purchased separately.

BMTK-SVN01D-EN

47

Image 55

Contents Building Automation System Page BMTK-SVN01D-EN February Page BMTK-SVN01D-EN BMTK-SVN01D-EN Contents Appendix B Appendix aTracker controller OverviewOverview Overview Tracker controller components Controller componentsTermination module Termination moduleMain module Main moduleDisplay module Display moduleModel number definition Model numbersTracker Controller specifications Tracker controller specificationsSpecification Description Tracker controller models 12 and 24 UCM capacities UCM maximum capacities for Tracker models 12Tracker model UCM type Maximum UCMs Tracker controller model Wshp UCM capacities UCM maximum capacities for Tracker model Wshp105 Store unused components until needed Avoid Equipment Damage Before installationVerify the shipment Inspect for shipping damageTracker controller post-installation checklist After installationFCC compliance Termination module mounting Verify location conformance to controller specificationsSelect a location for the controller Termination module mounting Minimum clearances Optimal touch screen viewing angles Mount the termination module Termination module conduit access and mounting holesSecuring the termination module to a conduit box Securing the termination module to a wallElectrical conduit installation Installing electrical conduitTermination module mounting Termination board wiring Termination board wiring Power wiring specifications Wire 24 Vac powerVac power Description Wire specifications Terminals Input and output wire specifications Wire optional inputs and outputsInput and output Description Wire specifications Terminals Wire the priority shutdown device Wire the alarm relayWire the thermistor Wire the utility pulse meterWire specifications Wire the UCMsSupplier Cable type Number Details Catalog Pairs Trane-approved wire suppliersSpecification Value Specifications for Echelon Level 4 compliant cablesFigure Note UCM wiring configurationsWire the UCMs Resistor color band table Termination resistor placement for Comm5 linksTolerance Color sequence Daisy-chain termination resistor placement Tracker Requirements for repeaters on Comm5 communication links Wire supported UCMsConnecting communication link shield wiring to repeater Comm5 daisy-chain repeater connection Termination board wiring Main module mounting Main module mounting Display module mounting Display module mounting Display module engagement Display module mounting Direct connection to PC workstation PC workstation wiringVerify PC workstation specifications Cable and adapter specifications for direct connectionPC workstation wiring Tracker direct connection to a PC workstation Modem connection to PC workstation Tracker modem connection to a PC workstation Ethernet connection to PC workstation Connecting over an existing LANTracker Controller PC Workstation Connecting through a hubConnecting with one cable LEDs TroubleshootingTroubleshooting components Service pin buttons and jumperTroubleshooting Color Description Number Alarm LEDTracker main logic board LEDs LED nameService pin buttons/jumper Function Main logic board service pin buttons and jumperSymptom/action troubleshooting Symptom/action troubleshootingSymptom Action Present of the proper severity to actuate the alarm output Symptom/action troubleshooting Troubleshooting Cleaning the touch screen MaintenanceCalibrating the touch screen Maintenance Required supplies Installation checklistsRequired supplies checklist Optional supplies checklistComm5 UCM identification and location Comm5 UCM identification and locationSpace Comfort Controllers 24 maximum Space Comfort Controllers Modules 4 maximum VariTrac central control panels 10 maximumPre-installation wiring notes Termination module post-installation checklist Termination module post-installation checklistCircuit Mandatory Test Actual value Wiring Temperature ºF Temperature ºC Sensor resistance Ohms x Thermistor sensor electrical characteristicsAppendix a Installation checklists Declaration of Conformity Mark of Compliance European Contact When and where issuedProduct Number BMTK000AA0A110 Electromagnetic EmissionNumerics IndexIndex Index Index Page Trane