Enviro Sonnet, C-11089 owner manual Kit Contents Quantity Description, Vent Kit Installation

Page 18

Initial Installation

QUALIFIED INSTALLERS ONLY

3.Remove log and ember set and all wrapping material from the stove. Remove wrapping material from log and embers and check for any damage. If damage is observed, do not use unit and contact your local dealer.

4.Refractory, glass doors, screen rails, screen mesh and log grates can be removed from the fireplace before installing the Sonnet. Check that the chimney cleanouts fit properly. The flue damper can be fully blocked open or removed for installation of the Sonnet; the smoke shelves, shields and baffles may be removed if attached by mechanical fasteners. IMPORTANT: Cutting any sheet-metal parts of a fireplace, in which the gas fireplace insert is to be installed, is prohibited.

5.If the fireplace opening is lower than 19” (483mm), remove the vent collar plate from the top of the insert by unscrewing the two (2) T-20 Torx screws located on the center top of the stove, and the four

(4) screws at the rear draft hood box. Slide the collar plate backwards. Properly secure the vent collar plate to the flexible vent pipe liner(s) previously installed in the chimney. Be careful not to over-stretch the liner(s).

6.Place the unit part way into the fireplace. Connect the household gas line into the 3⁄8” NPT receptical

at the lower right rear of the unit using locally approved methods. Place the electric cable so it can be connected to the power supply.

7.As you push the unit into its final position in the fireplace, if the vent collar plate was removed, reinstall it to the stove by sliding it along the draft hood and secure with the screws previously removed.

8.Using a 1⁄4” hex driver, adjust the levelling legs to ensure the unit is level and high enough if a base shelf and/or riser is to be installed. There are two (2) levelling legs on each side (shown in Figure 29).

Figure 29: Levelling legs position.

CONVERTING A DIRECT VENT FIREPLACE TO A B-VENT FIREPLACE:

Kit Contents:

Quantity Description

1Air Intake Plug

1Spill Switch with Wires & Bracket

Please ensure that all components are supplied with this kit. If components are missing or have been damaged, contact your dealer, distributor or courier company before starting this installation.

B-Vent Kit Installation:

Figure 30: Install of Intake Air Plug.

1.Install the air intake plug.

a)Place high temperature silicone on the outer surface of the ridges of the air intake plug (see Figure 30).

b)Slide the air intake plug into the air intake on the back of the unit.

2.Install spill switch assembly.

a)Use a flat head screwdriver or 1⁄4” socket to remove the nine (9) screws holding the back cover on (see Figure 47).

18

Image 18
Contents Installer For Your SafetyConsumer Safety Precautions GeneralTable of Contents Codes And Approvals Vented GAS Fireplace Heater Sonnet BV/DV NG/LPGSpecifications DimensionsTrimmable Operating Instructions Lighting and Turning OFF InstructionsAutomatic Pilot Mode Setting the TimeSetting C/24 hour or F/12 hour Clock Adjustment of Flame HeightSetting the Temperature Changing the Mode of OperationMAN Mode Manual Flame Height Adjustment Setting the TimerAdjusting the venturi air setting Component Sound & ReasonMaintenance And Service Pilot FlameRemote Handset ReceiverChanging Remote Handset Code Kit Parts List Conversion Kit InstallationOut of the firebox Each end that fit in to the brass nut but Initial Installation Mantle width and heightCan be started Kit Contents Quantity Description Vent Kit InstallationUnit Sheet metal screws evenly spaced Installation Instructions KIT ComponentsProper flame appearance. The amount of air Wall Bracket Top & Bottom Fan wiring diagram Tools RequiredFan Kit Installation Installing Power CordGrounding Power Cord Gas Line ConnectionTo Test Valve Pressures Opening Inlet Pressure Tap onSecondary Installation InstallationKit Contents Assembly Screw Hook Bracket To the TrimMinimum size of Large Installation RemovalHook Placements Ensure the Sonnet is turned off and allow the unit to coolEmpty firebox showing the ledges for the back logs Third Stage Log Set Installation Log Set and Ember Installation Never operate the fireplace with the glass door removedTrouble Shooting Problem Possible Cause SolutionPossible Cause Solution Valve’s SafetyPart Description Parts List ComponentsBV only NumberReference Part Description Part Number ComponentsDiagramParts Parts List Options Parts Diagram OptionsReference Option Description Part Number Warranty To the DealerWarranty Installation Data Sheet