Enviro C-11089, Sonnet owner manual Unit

Page 19

Initial Installation

QUALIFIED INSTALLERS ONLY

b)Cut the tie strap from around the wires for the spill switch.

c)Feed the connector end of both wires through the hole in the bottom left corner of the back panel (see Figure 31).

d)Using needle nose pliers remove the jumper wire on the thermocouple (see Figure 32).

e)Attach the connectors for the spill switch wiring to the connectors the jumper was removed from (see Figure 33).

f)Re-attach the back panel.

g)Using a T-20 screwdriver remove the four (4) screws that hold the flue slider bottom plate. Pull the plate down then out, ensuring that the gasket comes with the plate (see Figure 34).

 

 

 

 

 

Figure 32: Remove Jumper

 

Figure 33: Spill Switch Wires

 

From Thermocouple.

 

Connect to Thermocouple.

 

 

 

 

 

 

 

 

 

 

 

Figure 34: Remove Flue Slider Plate & Gasket.

Figure 31: Spill Switch Wires Fed Through

Back Panel.

h)Install spill switch bracket with two (2) of the screws removed in the previous step. The spill switch must be angled under the opening (see Figure 35)

3.Remove screw from draft tube and air intake covers.

a)Remove the glass door as shown in the

MAINTENANCE AND SERVICE - GLASS DOOR

REMOVAL.

b)Using a T-20 screwdriver remove the screw that is in the draft tube pointed at in Figure 28.

c)Remove the two (2) air intake covers below the firebox (refer to Figure 36), they can be pried out using a flat head screwdriver.

d)Install door.

Figure 35: Install Spill Switch

on Bracket.

4.Test fire the appliance and ensure proper operation. A venturi adjustment (Figure 7) could be required

to achieve an efficient flame, refer to Figure 77. Improper operation or adjustment could result in Carbon Monoxide production causing personal injury or property damage.

Figure 36: Air Intake Cover Plates.

Note: To convert a B-Vent to a Direct Vent, remove the air intake plug, remove the spill switch assembly and re-install the flue slider bottom plate, re-install the jumper onto the thermocouple wire, re-install the air intake cover plates, install the proper venting, re-install the screw into the draft tube at the front top

of the unit.

19

Image 19
Contents For Your Safety InstallerConsumer General Safety PrecautionsTable of Contents Vented GAS Fireplace Heater Sonnet BV/DV NG/LPG Codes And ApprovalsDimensions SpecificationsTrimmable Lighting and Turning OFF Instructions Operating InstructionsAdjustment of Flame Height Setting the TimeSetting C/24 hour or F/12 hour Clock Automatic Pilot ModeSetting the Timer Changing the Mode of OperationMAN Mode Manual Flame Height Adjustment Setting the TemperatureComponent Sound & Reason Adjusting the venturi air settingPilot Flame Maintenance And ServiceReceiver Remote HandsetChanging Remote Handset Code Conversion Kit Installation Kit Parts ListOut of the firebox Each end that fit in to the brass nut but Mantle width and height Initial InstallationCan be started Vent Kit Installation Kit Contents Quantity DescriptionUnit Sheet metal screws evenly spaced KIT Components Installation InstructionsProper flame appearance. The amount of air Wall Bracket Top & Bottom Tools Required Fan wiring diagramInstalling Power Cord Fan Kit InstallationGas Line Connection Grounding Power CordOpening Inlet Pressure Tap on To Test Valve PressuresInstallation Secondary InstallationKit Contents Screw Hook Bracket To the Trim AssemblyMinimum size of Large Removal InstallationEnsure the Sonnet is turned off and allow the unit to cool Hook PlacementsEmpty firebox showing the ledges for the back logs Third Stage Log Set Installation Never operate the fireplace with the glass door removed Log Set and Ember InstallationProblem Possible Cause Solution Trouble ShootingValve’s Safety Possible Cause SolutionNumber Parts List ComponentsBV only Part DescriptionReference Part Description Part Number ComponentsDiagramParts Parts Diagram Options Parts List OptionsReference Option Description Part Number To the Dealer WarrantyWarranty Installation Data Sheet