Empire Comfort Systems DVP48FP7, DVP48FP3, DVP48FP9, DVP42FP9, DVP42FP3 Important Safety Information

Page 3

IMPORTANT SAFETY INFORMATION

Beforeenclosingtheventpipeassembly,operatetheappliancetoensureitisventingproperly.

DO NOT OPERATE THIS APPLIANCE WITHOUT GLASS FRONT PANEL INSTALLED

If this appliance is installed directly on carpeting,

 

placed on or near the appliance.

 

tile or other combustible material other than wood

Adequate accessibility clearances for servicing and

 

flooring the appliance shall be installed on a metal or

 

 

proper operation.

 

wood panel extending the full width and depth of the

 

 

This appliance must not share or be connected to a

 

appliance.

 

The base referred to above does not mean the fireproof

 

flue serving a separate solid-fuel burning appliance.

 

Keep the area around your appliance clear of

 

base as used on wood stoves. The protection is for rugs

 

that are extremely thick and light colored tile.

 

combustible materials, gasoline and other flammable

Children and adults should be alerted to the hazards

 

vapor and liquids.

Under no circumstances should any solid fuels (wood,

 

of high surface temperatures and should stay away

 

to avoid burns or clothing ignition.

 

coal, paper or cardboard etc.) be used in this appli-

Young children should be carefully supervised when

 

ance.

The flow of combustion and ventilation air must not

 

they are in the same room as the appliance.

Clothing or other flammable material should not be

 

be obstructed in any way.

 

 

 

 

 

 

Due to high temperatures the appliance should be located out of traffic and away from furniture and draperies.

The glass front or any part removed for servicing the appliance must be replaced prior to operating the appliance. Work should be done by a qualified service person.

Keep burner and control compartment clean.

Vent cap is hot while fireplace is in operation.

Installation and repair should be done by a QUALIFIED SERVICE PERSON. The appliance should be inspected before use and at least annually by a qualified service person. More frequent cleaning may be required due to excessive lint from carpeting, bedding materials, etc. It is imperative that control compartments, burners and circulating air passageways of the appliance be kept clean.

DO NOT put anything around the fireplace that will obstruct the flow of ventilation air.

Clearance in accordance with local installation codes and the requirements of the gas supplier.

DO keep the appliance area clear and free from combustible material, gasoline and otherflammable vapors and liquids.

DO examine venting system periodically and replace damaged parts.

DOmakeaperiodicvisualcheckofpilotandburners. Clean and replace damaged parts.

CAUTION: The glass used in your fireplace is tempered glass. If the glass is cracked or damaged in any way, it should be replaced only with a complete glass frame assembly from Empire. See parts list on Page 40 for ordering.

DO NOT use this fireplace if any part has been under water. Immediately call a qualified service technician to inspect the heater and to replace any part of the control system and any gas control which has been under water.

Any safety screen or guard removed for servicing an appliance must be replaced prior to operating the appliance.

17375-6-0705

Page 3

Image 3
Contents Installation Instructions Table of Contents Important Safety Information LP-GAS Warning Odor Safety Information for Users of LP GASIntroduction Fireplace Dimensions SpecificationsClearances Figure Mantel Chart FigureClearances Locating FireplaceInstalling a New Main Gas Cock GAS SupplyChecking Manifold Pressures Rear Vent Conversion Vent SystemsConverting flue take-off to rear venting Installation Framing and FinishingVent Pipe Clearance Flush Mount Mantel Installation Figure Framing FigureFinishing Figures 12 VERTICAL, 90 Elbow with Horizontal Termination Flush Wall InstallationCombustible Surround Installation Vent Runs Figures 14, 15, 16, 17Model VERTICAL, 90 Elbow toExample a Venting Graph Dimensions in FeetVenting Fireplace TOP To Use the Vent Graph FigureVenting Fireplace TOP Below Grade InstallationFireplace Hard Elbow Dimensions Series DVP42FP Examples TOP Vent RUN Theunit Caps Venting Fireplace RearExamples Rear Vent RUN Vertical Sidewall Installations Termination ClearancesInformation on Various Venting Routes and Components Vent Clearances Vent System Identification Installing Vent Components FigureInstalling Support Brackets Figure Installing Firestops Figures 38, 39, 40Framing and Finishing See Horizontal Termination Page 24 and Vertical Termination Horizontal TerminationDVVK-5F Flex Vent Instructions Determining Minimum Vent Height Above the Roof General MaintenanceInstalling the Vent System in a Chase Vertical TerminationVertical Termination Reassembly and Resealing Vent Pipe SystemLOG Placement 3 LOG SET Pilot Flame Figure Operating InstructionsMillivolt System Initial LightingTRW Standing Pilot Wiring Diagram Standing Pilot Lighting Instructions For Your Safety Read Before LightingGlass soots Standing Pilot TroubleshootingFrequent pilot outage problem Pilot and main burner extinguish while in operationElectrical Connection Figure Intermittent Pilot Operating InstructionsWhat to do if YOU Smell GAS For Your Safety Read Before LightingTrial for Ignition S8600H Intermittent Ignition Module SpecificationsCheckout OperationMain Burner Operation Safety LockoutARC Length Action Ignition System Checks Check ignition cable. Make sureIntermittent Pilot Troubleshooting Thermopiles Transmitter SignalFunctions Receiver Shutdown of BurnerRF Transmitter Functions Wiring Diagram with Blower RF Standing Pilot Lighting Instructions Please Note Maintenance and ServiceParts View Parts List Blower Wheels Blower MotorVolt AC Optional Brick Liner Installation Instructions Junction BOX Wiring Installation InstructionsFBB4 AccessoriesService Notes HOW to Order Repair Parts Service Notes