Harman-Kardon AVR507 owner manual Surround

Page 20

System Configuration

If you wish to customize the speaker size individu- ally to each input, make certain that the cursor is on the BASS MGR line and press the ‹/› Buttons E so that INDEPENDENT appears in highlighted video. When this setting is entered all speaker size settings will be shown with their factory default size in the menu and all other inputs will turn to INDEPENDENT too. Now you should enter the speaker size settings prefered for the input selected, as described below. Remember that in this case the size set- tings just entered will apply to the current input ONLY, and you will need to go back to the INPUT menu to select another input, and then return to this menu page again to change the set- tings for the next input. Repeat the procedure for any input where you wish to have a set of speaker configuration different from the default settings.

2.Begin the speaker size setup process by making certain that the cursor is pointing toward the LEFT/RIGHT line, which sets the configura- tion for the front left and right speakers. If you wish to make a change to the front speakers’

configuration, press the ‹/ › Buttons E so that either LARGE or SMALL appears, match- ing the appropriate description from the definitions shown above.

When SMALL is selected, low-frequency front channel sounds will be sent only to the subwoofer output. If you choose this option and there is no subwoofer connected, you will not hear any low- frequency sounds with front channel signals.

When LARGE is selected, a full-range output will be sent to the front left and front right

outputs. Depending on the choice made in the SUBWOOFER line in this menu (see below), the front left and right bass information may also be directed to the subwoofer.

NOTE: When the front speakers are set to the LARGE option and the surround mode is set to "Surround Off", or pure two-channel stereo, when an analog signal source is present it will be routed directly from the input to the volume control without being digitized or processed. If you have full-range front speakers and wish to remove all digital processing from the circuit path, select this configuration. If you wish to set this option for use with only one input, such as a CD player that uses an external DAC or an optional, external phono preamp, you must choose the INDEPENDENT setting on the BASS MGR line at the bottom of this menu so that only those inputs where the analog bypass is desired will be routed in this fashion, while other analog inputs such as a VCR or cable box will be digitized for surround processing.

Important Note: When a speaker set with a subwoofer and two front satellites connected to the Sub´s speaker outputs is used, the Sub´s inputs must be connected to the Front speaker outputs and LARGE must be selected for the front speakers (and NONE for the sub- woofer, see below).

3.When you have completed your selection for the front channel, press the ¤ Button Don the remote to move the cursor to CENTER.

4. Press the ‹/› Buttons E on the remote to select the option that best describes your center speaker, based on the speaker definitions shown below.

When SMALL is selected, low-frequency center channel sounds will be sent to the Fronts, if they are set to LARGE and Sub is turned off (see be- low). When Sub is on, low frequency center chan- nel sounds will be sent to the subwoofer only.

When LARGE is selected, a full-range output will be sent to the center speaker output, and NO center channel signal will be sent to the sub- woofer output (except when the Pro Logic II Music mode is in use).

NOTE: If you choose Logic 7 as the surround mode for the particular input source for which you are configuring your speakers, the AVR will not make the LARGE option available for the center speaker. This is due to the requirements of Logic 7 processing, and does not indicate a problem with your receiver.

When NONE is selected, no signals will be sent to the center-channel output. The receiver will operate in a “phantom” center channel mode. Center-channel information will be sent to the left and right front channel outputs and the center channel bass will be sent to the subwoofer output when SUB L/R+LFE is selected in the SUBWOOFER line in this menu (see below). This mode is needed if no Center speaker is used. Note that when the Logic 7 Cinema or Enhanced surround modes are selected a Center speaker must be used, the Logic 7 Music mode works well without a Center too.

5.When you have completed your selection for the center channel, press the ¤ Button D on the remote to move the cursor to

SURROUND.

6. Press the ‹/› Buttons E on the remote to select the option that best describes the sur- round speakers in your system based on the speak- er definitions shown on page 21.

When SMALL is selected, with all digital sur- round modes low-frequency surround channel sounds will be sent to the Fronts when Sub is turned off or to the subwoofer output when Sub is on. With any analog surround mode the rear bass feed depends on the mode selected and the setting of the Sub and front speakers.

When LARGE is selected, a full-range output will be sent to the surround channel outputs (with all analog and digital surround modes), and except with Hall and Theater modes, NO surround chan- nel bass will be sent to the subwoofer output.

When NONE is selected, surround-sound infor- mation will be split between the front left and front right outputs. For optimal performance when no surround speakers are in use, the Dolby 3 Stereo mode should be used.

When you are using surround back speakers with your system, press the ¤ Button Don the remote to move the cursor to SURR BACK. This line serves two functions in that it not only configures the setting for the surround back chan- nels when they are present, it also tells the AVR’s processing system to configure the unit for either 5.1 or 6.1/7.1 operation.

Press the ‹/ › Buttons on the remote to select the option that best describes the speakers in use at the left and right back surround positions based on the definitions on this page:

When NONE is selected, the system will adjust so that only 5.1-channel surround processing/ decoding modes are available and the surround back amplifier channels will not be used. When this is the case for your system you may wish to take advantage of the availability of this amplifier channel pair for use in powering a second set of speakers that have their source selected by the AVR’s multiroom control system. See page 37 for more information.

When SMALL is selected the system will adjust so that the full complement of 6.1/7.1 surround processing/decoding modes are available, and low-frequency information below the crossover point (identical with the one for the surround speakers) will be sent to the subwoofer output when the subwoofer is set to ON, or to the Front LEFT/RIGHT when subwoofer is set to OFF.

When LARGE is selected the system will adjust so that the full complement of 6.1/7.1 surround processing/decoding modes are available, and a full-range signal will be sent to the surround back channels, with no low-frequency information sent to the subwoofer output.

7.When you have completed your selection for the surround channels, press the ¤ Button Don the remote to move the cursor to SUBWOOFER.

8. Press the ‹/› Buttons E on the remote to select the option that best describes your system.

The choices available for the subwoofer position will depend on the settings for the other speakers, particularly the front left/right positions.

If the front left/right speakers are set to SMALL, the subwoofer will automatically be set to SUB, which is the “on” position.

20SYSTEM CONFIGURATION

Page 19 Page 21
Image 20
Page 19 Page 21
Contents AVR507 Limited Edition Audio/Video Receiver Table of Contents Declaration of ConformityFront panel analog A/V inputs Description and FeaturesIntroduction Unpacking Safety InformationImportant Safety Information Front Panel Controls Information on digital audio # Preset Stations Selector Press thisDigital Input Selector When playing a Rear Panel Connections Digital Audio Outputs Connect theseUnswitched Outlet + and negative terminalsMain Remote Control Functions Channel/8 Channel Direct Input See page 32 for more informationMovies Zone II Remote Control Functions ∆ Play Forward/Reverse/Stop ˚ MuteVideo Equipment Connections Installation and ConnectionsAudio Equipment Connections Scart A/V Connections Video Input jacksVideo Connection Notes Important Note for Adapter CablesIf you use a unit providing RGB signals on a Important Note for the Use SCART-Cinch AdaptersSystem and Power Connections Main Room Remote Control ExtensionAC Power Connections Multiroom IR LinkSpeaker Placement Speaker SelectionSystem Configuration Using the On-Screen DisplaySystem Setup First Turn OnSet Button Fto bring up the Speaker Setup menu Figure Input SetupSpeaker Setup Surround Within five seconds, either press the ‹/› buttons ¤ Button Dso that the cursor is next to Surround SetupOr 6.1/7.1 speaker output configuration is in use Configuring the Surround Off Stereo Modes Stereo-Direct Bypass ModeStereo-Digital Mode Delay SettingsNight Mode Settings Output Level AdjustmentUsing EzSet Speaker/Channel IndicatorsSo that on is highlighted When all channels have the same output level Sensor and Indicator offUp the Volume until you can hear the test noise clearly Surround Mode Chart OperationNo delay available Mix of the in-phase material of the left and right channelsNo surround channels But no surround speakersChannel/8-Channel Direct Input Basic OperationSource Selection Surround Mode Selection Volume Up/Down ButtonsDigital Audio Playback Dolby DigitalPCM Audio Playback Selecting a Digital SourceSurround Mode Types Digital Bitstream IndicatorsAudio, while the main feature is available PCM Playback IndicationsOutput Level Adjustment With Source Signals Night ModeNormal output level adjustment for Tape RecordingMemory Backup Indicator SelectIndicator off Select to activate the sensorAdvanced Features Turn On Volume LevelDisplay Brightness Surround Back/Multiroom SpeakerAdvanced Features / Multiroom Operation Semi-OSD SettingsFull-OSD Time Out Adjustment InstallationMultiroom Setup Multiroom OperationMultiroom Operation If the Remote IR Output jackTuner Operation Basic Tuner OperationRDS Tuning RDS OperationRDS Display Options Program Search PTYProgramming the Remote with Codes Direct Code EntryTurn on the unit you wish to program into the AVR remote Must be repeated firstMacro Programming Programming the RemoteCode Readout Channel Control Punch-Through Volume Punch-ThroughProgrammed Device Functions Resetting the Remote Memory Function List SPLAVR DVD Troubleshooting Guide Processor ResetPower Switch 1 is pushed Remote sensor ¯ is obscuredTechnical Specifications Harman Consumer International

AVR507 specifications

The Harman-Kardon AVR507 is a distinguished audio/video receiver that stands out in the realm of home entertainment systems. Launched in the early 2000s, the AVR507 quickly gained a reputation for its powerful performance, elegant design, and advanced feature set.

At the heart of the AVR507 is its robust amplifier section, delivering a substantial output power of 70 watts per channel across seven channels. This ensures immersive surround sound experiences that bring movies, music, and games to life with clarity and depth. The receiver supports various surround sound formats, including Dolby Digital and DTS, enabling users to enjoy cinematic audio quality right in their living room.

One of the key highlights of the AVR507 is its remarkable multi-zone capabilities. Users can setup different audio zones throughout their home, making it possible to play distinct audio sources in separate areas. This can be especially beneficial for larger homes or entertaining spaces where various preferences for music or audio may exist.

The AVR507 also boasts a comprehensive suite of connectivity options. With multiple HDMI inputs, component video, and optical audio inputs, it accommodates a wide range of devices, from Blu-ray players to gaming consoles. It also features an integrated AM/FM tuner, allowing users to enjoy their favorite radio stations without the need for additional equipment.

In terms of user experience, the receiver employs an intuitive on-screen graphical user interface, facilitating easy navigation through menus and settings. The included remote control offers convenient access to all of the AVR507's features, making for a smooth and user-friendly operation.

Another noteworthy technology within the AVR507 is its built-in digital signal processing (DSP), which enhances audio playback by optimizing sound quality based on the specific setup and speaker configuration. This ensures that whether you are watching a high-octane action film or listening to a subtle acoustic track, the audio remains balanced and rich.

The AVR507 also incorporates high-quality DACs (digital-to-analog converters) that are crucial for exceptional audio fidelity. The result is a receiver that not only excels in power and performance but also provides a refined listening experience.

In summary, the Harman-Kardon AVR507 is a versatile and powerful audio/video receiver that embodies a blend of advanced technology, user-centric design, and superb performance. Its multitude of features makes it an excellent choice for anyone looking to elevate their home entertainment experience.
Top Page Image Contents