Harman-Kardon AVR507 Advanced Features / Multiroom Operation, Semi-OSD Settings, Installation

Page 36

Advanced Features / Multiroom Operation

Semi-OSD Settings

The semi-OSD system places one line messages at the lower third of the video display screen whenever the Volume, Input Source, Surround mode or tuner frequency of any of the configura- tion settings are changed. The semi-OSD system is helpful in that enables you to have feedback on any control changes or remote commands using the video display when it is difficult to view the front-panel displays. However, you may occasionally prefer to turn these displays off for a particular listening session. You may also want to adjust the length of time the displays remain on the screen. Both of those options are possible with the AVR.

To turn off the semi-OSD system, you will need to make an adjustment in the ADVANCED SELECT menu (Figure 11). To start the adjustment, press the OSD button Lto bring the MASTER MENU to the screen. Press the

⁄Button D, until the on-screen› cursor is next to the ADVANCED line. Press the Set Button Fto enter the ADVANCED SELECT menu.

At the ADVANCED SELECT menu make certain that the on-screen › cursor is next to the SEMI OSD line by pressing the ⁄/¤ but- tons Das needed. Next, press the › button

so that the word OFF is highlighted in the video display.

Note that this setting is temporary and will remain active only until it is changed or until the AVR is turned off. Once the unit is turned off, the semi-OSD displays will remain activated, even if they were switched off for the previous listening session.

To change the length of time that the semi-OSD displays remain on the screen, go to the ADVANCED SELECT Menu as outlined earlier, and press the ⁄/¤ buttons Das need- ed, until the on-screen › cursor is next to the SEMI-OSD TIME OUT line. Next, press the ‹/› Buttons E until the desired time in seconds is displayed. Note that unlike most of the other options in this menu, this is a perma- nent setting change, and the time-out entry will remain in effect until it is changed, even when the unit is turned off.

If you wish to make other adjustments in the menu, press the ⁄/¤ Buttons Duntil the on- screen › cursor is next to the desired setting or the BACK TO MASTER MENU line and press the Set button F. If you have no other adjustments to make, press the OSD Button L to exit the menu system.

Full-OSD Time Out Adjustment

The FULL OSD menu system is used to simplify the setup and adjustment of the

AVR using a series of on-screen menus. The fac- tory default setting for these menus leaves them on the screen for 20 seconds after a period of inactivity before they disappear from the screen or Time Out. This Time Out is a safety measure to prevent the menu text from burning into the CRTs in your monitor or projector, which might happen if they were left on indefinitely. However, some viewers may prefer a slightly longer or shorter period before the Time Out display.

To change the Full-OSD Time Out, you will need to make an adjustment in the ADVANCED SELECT menu (Figure 11). To start the adjustment, press the OSD button Lto bring the MASTER MENU to the screen. Press the

⁄button D, until the on-screen › cursor is next to the ADVANCED line. Press the Set Button Fto enter the ADVANCED SELECT menu (Figure 11).

At the ADVANCED SELECT menu make certain that the on-screen › cursor is next to the FULL OSD TIME OUT line by pressing the ⁄/¤ Buttons Das needed. Next, press the

‹/ › buttons E until the desired time is displayed in seconds. Note that unlike most of the other options in this menu, this is a perma- nent setting change, and the time-out entry will remain in effect until it is changed, even when the unit is turned off.

If you wish to make other adjustments in the menu, press the ⁄/¤ Buttons Duntil the on-screen › cursor is next to the desired setting or the BACK TO MASTER MENU line and press the Set button F. If you have no other adjustments to make, press the OSD Button L to exit the menu system.

Multiroom Operation

The AVR is fully equipped to operate as the con- trol center for a complete multiroom system that is capable of sending one source to a second zone in the house while separate source is lis- tened to in the main room. In addition to provid- ing for control over the selection of the remote source and its volume, the AVR offers a compre- hensive range of options for powering the speakers in the second zone.

•Using the line-level Multiroom Audio Outputs , the selected source may be fed to optional, external power amplifiers that may be matched to the specifics of the installation.

•When the main room system is configured for 5.1 operation, the Surround Back Left/Right amplifier channels may be used to power the remote zone so that no additional amplifiers are required.

In addition, the AVR includes a remote IR sensor input so that remote control commands from the Zone II remote included with the unit may be transmitted to the unit, while standard IR input/output jacks allow the remote zone’s com- mands to be sent to compatible IR-controlled source devices.

Installation

Although simple remote room systems may be installed by the average do-it-yourself hobbyist, the complexity of your multizone/multiroom sys- tem involves running wires inside of walls where the services of a specially trained installer may be required. Regardless of who does the work, please remember that local building codes may govern in-wall electrical work, including proper specification of any wiring used and the way in which it is connected. You are responsible for making certain that all Multiroom installation work is done properly and in compliance with all applicable codes and regulations.

For standard installations, follow the instructions shown on page 16 for the connection of speaker wire and IR remote wiring to the AVR.

For installations where the Surround Back Left/Right amplifier channels are used to power the remote zone, make certain that the system is configured for that type of operation, as shown on page 35.

36ADVANCED FEATURES / MULTIROOM

Page 35 Page 37
Image 36
Page 35 Page 37
Contents AVR507 Limited Edition Audio/Video Receiver Table of Contents Declaration of ConformityDescription and Features IntroductionFront panel analog A/V inputs Safety Information Important Safety InformationUnpacking Front Panel Controls # Preset Stations Selector Press this Digital Input Selector When playing aInformation on digital audio Rear Panel Connections Digital Audio Outputs Connect theseUnswitched Outlet + and negative terminalsMain Remote Control Functions Channel/8 Channel Direct Input See page 32 for more informationMovies Zone II Remote Control Functions ∆ Play Forward/Reverse/Stop ˚ MuteInstallation and Connections Audio Equipment ConnectionsVideo Equipment Connections Scart A/V Connections Video Input jacksVideo Connection Notes Important Note for Adapter CablesIf you use a unit providing RGB signals on a Important Note for the Use SCART-Cinch AdaptersSystem and Power Connections Main Room Remote Control ExtensionAC Power Connections Multiroom IR LinkSpeaker Placement Speaker SelectionSystem Configuration Using the On-Screen DisplaySystem Setup First Turn OnInput Setup Speaker SetupSet Button Fto bring up the Speaker Setup menu Figure Surround Within five seconds, either press the ‹/› buttons Surround Setup Or 6.1/7.1 speaker output configuration is in use¤ Button Dso that the cursor is next to Configuring the Surround Off Stereo Modes Stereo-Direct Bypass ModeStereo-Digital Mode Delay SettingsNight Mode Settings Output Level AdjustmentUsing EzSet Speaker/Channel IndicatorsSo that on is highlighted Sensor and Indicator off Up the Volume until you can hear the test noise clearlyWhen all channels have the same output level Surround Mode Chart OperationNo delay available Mix of the in-phase material of the left and right channelsNo surround channels But no surround speakersBasic Operation Source SelectionChannel/8-Channel Direct Input Surround Mode Selection Volume Up/Down ButtonsDigital Audio Playback Dolby DigitalPCM Audio Playback Selecting a Digital SourceSurround Mode Types Digital Bitstream IndicatorsAudio, while the main feature is available PCM Playback IndicationsOutput Level Adjustment With Source Signals Night ModeNormal output level adjustment for Tape RecordingMemory Backup Indicator SelectIndicator off Select to activate the sensorAdvanced Features Turn On Volume LevelDisplay Brightness Surround Back/Multiroom SpeakerAdvanced Features / Multiroom Operation Semi-OSD SettingsFull-OSD Time Out Adjustment InstallationMultiroom Setup Multiroom OperationMultiroom Operation If the Remote IR Output jackTuner Operation Basic Tuner OperationRDS Tuning RDS OperationRDS Display Options Program Search PTYProgramming the Remote with Codes Direct Code EntryTurn on the unit you wish to program into the AVR remote Must be repeated firstProgramming the Remote Code ReadoutMacro Programming Volume Punch-Through Programmed Device FunctionsChannel Control Punch-Through Resetting the Remote Memory Function List SPLAVR DVD Troubleshooting Guide Processor ResetPower Switch 1 is pushed Remote sensor ¯ is obscuredTechnical Specifications Harman Consumer International

AVR507 specifications

The Harman-Kardon AVR507 is a distinguished audio/video receiver that stands out in the realm of home entertainment systems. Launched in the early 2000s, the AVR507 quickly gained a reputation for its powerful performance, elegant design, and advanced feature set.

At the heart of the AVR507 is its robust amplifier section, delivering a substantial output power of 70 watts per channel across seven channels. This ensures immersive surround sound experiences that bring movies, music, and games to life with clarity and depth. The receiver supports various surround sound formats, including Dolby Digital and DTS, enabling users to enjoy cinematic audio quality right in their living room.

One of the key highlights of the AVR507 is its remarkable multi-zone capabilities. Users can setup different audio zones throughout their home, making it possible to play distinct audio sources in separate areas. This can be especially beneficial for larger homes or entertaining spaces where various preferences for music or audio may exist.

The AVR507 also boasts a comprehensive suite of connectivity options. With multiple HDMI inputs, component video, and optical audio inputs, it accommodates a wide range of devices, from Blu-ray players to gaming consoles. It also features an integrated AM/FM tuner, allowing users to enjoy their favorite radio stations without the need for additional equipment.

In terms of user experience, the receiver employs an intuitive on-screen graphical user interface, facilitating easy navigation through menus and settings. The included remote control offers convenient access to all of the AVR507's features, making for a smooth and user-friendly operation.

Another noteworthy technology within the AVR507 is its built-in digital signal processing (DSP), which enhances audio playback by optimizing sound quality based on the specific setup and speaker configuration. This ensures that whether you are watching a high-octane action film or listening to a subtle acoustic track, the audio remains balanced and rich.

The AVR507 also incorporates high-quality DACs (digital-to-analog converters) that are crucial for exceptional audio fidelity. The result is a receiver that not only excels in power and performance but also provides a refined listening experience.

In summary, the Harman-Kardon AVR507 is a versatile and powerful audio/video receiver that embodies a blend of advanced technology, user-centric design, and superb performance. Its multitude of features makes it an excellent choice for anyone looking to elevate their home entertainment experience.
Top Page Image Contents