Harman-Kardon AVR507 # Preset Stations Selector Press this, Digital Input Selector When playing a

Page 6

Front Panel Controls

7Selector Buttons: When you are establishing the AVR’s configuration settings, use these buttons to select from the choices available, as shown in the Main Information Display ˜.

8Tone Mode: Pressing this button enables or disables the Balance, Bass and Treble tone controls. When the button is pressed so that the words TONE IN appear in the Main Information Display ˜, the settings of the Bass and Treble Ú controls and of the Balance control Ò will affect the output signals. When the button is pressed so that the words TONE OUT appear in the Main Information Display ˜, the output signal will be “flat,” without any balance, bass or treble alteration.

9Surround Mode Selector: Press this button to select from among the available surround mode options for the mode group selected. The specific modes will vary based on the number of speakers available, the mode group and if the input source is digital or analog. For example, press the Surround Mode Group Selector 5 to select a mode grouping such as Dolby or Logic 7, and then press this button to see the mode choices available. For more information on mode selection, see page 30.

)Tuning Selector: Press the left side of the button to tune lower frequency stations and the right side of the button to tune higher frequency stations. When a station with a strong signal is reached, MANUAL TUNED or AUTO TUNED will appear in the Main Information Display ˜ (see page 38 for more information on tuning stations).

!Tuner Band Selector: Pressing this button will automatically switch the AVR to the Tuner mode. Pressing it again will switch between the AM and FM frequency bands, holding it pressed for some seconds will switch between stereo and mono receiving and between automatic and manual tuning mode (See page 38 for more information on the tuner).

@Set Button: When making choices during the setup and configuration process, press this button to enter the desired setting as shown in the Main Information Display ˜into the AVR’s memory. The set button may also be used to change the display brightness. (See page 35.)

#Preset Stations Selector: Press this

button to scroll up or down through the list of stations that have been entered into the preset memory. (See page 38 for more information on tuner programming.)

$Speaker/Channel Input Indicators: These indicators are multipurpose, indicating either the speaker type selected for each channel or the incoming data-signal configuration. The left, center, right, right surround and left surround speaker indicators are composed of three boxes, while the subwoofer is a single box. The center box lights when a “Small” speaker is selected, and the two outer boxes light when “Large” speakers are selected. When none of the boxes are lit for the center, surround or subwoofer channels, no speaker has been selected for that position. (See page 19 for more information on configuring speakers.) The letters inside each of the center boxes display active input channels. For standard analog inputs, only the L and R will light, indicating a stereo input. When a digital source is playing, the indica- tors will light to display the channels begin received at the digital input. When the letters flash, the digital input has been interrupted. (See page 21 for more information on the Channel Indicators).

%Input Source Selector: Press this button to change the input by scrolling through the list of input sources.

^RDS Select Button: Press this button to display the various messages that are part of the RDS data system of the AVR’s tuner.

(See page 39 for more information on RDS).

&Delay: Press this button to begin the sequence of steps required to enter delay time settings. (See page 23 for more information on delay times.)

*Digital Optical 3 Input: Connect the optical digital audio output of an audio or video product to this jack. When the Input is not in use, be certain to keep the plastic cap installed to avoid dust contamination that might degrade future performance.

(Surround Mode Indicators: A blue LED will light in front of the surround mode that is currently in use.

ÓDigital Coax 3 Input: This jack is normally used for connection to the output of portable digital audio devices, video game consoles or other products that have a coax digital jack.

ÔVideo 4 Input Jacks: These audio/video jacks may be used for temporary connection to video games or portable audio/video products such as camcorders and portable audio players.

Bass Control: Turn this control to modify the low frequency output of the left/right channels by as much as ±10dB. Set this control to a suitable position for your taste or room acoustics.

ÒBalance Control: Turn this control to change the relative volume for the front left/right channels.

NOTE: For proper operation of the surround modes this control should be at the midpoint or “12 o’clock” position.

ÚTreble Control: Turn this control to modify the high frequency output of the left/right channels by as much as ±10dB. Set this control to a suitable position for your taste or room acoustics.

ÛDigital Input Selector: When playing a

source that has a digital output, press this button

to select between the Optical and Coaxial Digital inputs. (See pages 22-24 for more

information on digital audio.)

ÙChannel Select Button: Press this button to begin the process of trimming the channel output levels using an external audio source. (For more information on output level trim adjustment, see page 33.)

ıVolume Control: Turn this knob clockwise to increase the volume, counterclockwise to decrease the volume. If the AVR is muted, adjust- ing volume control will automatically release the unit from the silenced condition.

ˆInput indicators: A blue LED will light in front of the input that is currently being used as the source for the AVR.

˜Main Information Display: This display delivers messages and status indications to help you operate the receiver.

¯Remote Sensor Window: The sensor behind this window receives infrared signals from the remote control. Aim the remote at this area and do not block or cover it unless an external remote sensor is installed.

6FRONT PANEL CONTROLS

Page 5 Page 7
Image 6
Page 5 Page 7
Contents AVR507 Limited Edition Audio/Video Receiver Table of Contents Declaration of ConformityDescription and Features IntroductionFront panel analog A/V inputs Safety Information Important Safety InformationUnpacking Front Panel Controls # Preset Stations Selector Press this Digital Input Selector When playing aInformation on digital audio Rear Panel Connections Digital Audio Outputs Connect theseUnswitched Outlet + and negative terminalsMain Remote Control Functions Channel/8 Channel Direct Input See page 32 for more informationMovies Zone II Remote Control Functions ∆ Play Forward/Reverse/Stop ˚ MuteInstallation and Connections Audio Equipment ConnectionsVideo Equipment Connections Video Connection Notes Scart A/V ConnectionsVideo Input jacks Important Note for Adapter CablesIf you use a unit providing RGB signals on a Important Note for the Use SCART-Cinch AdaptersAC Power Connections System and Power ConnectionsMain Room Remote Control Extension Multiroom IR LinkSpeaker Placement Speaker SelectionSystem Setup System ConfigurationUsing the On-Screen Display First Turn OnInput Setup Speaker SetupSet Button Fto bring up the Speaker Setup menu Figure Surround Within five seconds, either press the ‹/› buttons Surround Setup Or 6.1/7.1 speaker output configuration is in use¤ Button Dso that the cursor is next to Stereo-Digital Mode Configuring the Surround Off Stereo ModesStereo-Direct Bypass Mode Delay SettingsUsing EzSet Night Mode SettingsOutput Level Adjustment Speaker/Channel IndicatorsSo that on is highlighted Sensor and Indicator off Up the Volume until you can hear the test noise clearlyWhen all channels have the same output level Surround Mode Chart OperationNo surround channels No delay availableMix of the in-phase material of the left and right channels But no surround speakersBasic Operation Source SelectionChannel/8-Channel Direct Input Surround Mode Selection Volume Up/Down ButtonsPCM Audio Playback Digital Audio PlaybackDolby Digital Selecting a Digital SourceAudio, while the main feature is available Surround Mode TypesDigital Bitstream Indicators PCM Playback IndicationsNormal output level adjustment for Output Level Adjustment With Source SignalsNight Mode Tape RecordingIndicator off Memory BackupIndicator Select Select to activate the sensorDisplay Brightness Advanced FeaturesTurn On Volume Level Surround Back/Multiroom SpeakerFull-OSD Time Out Adjustment Advanced Features / Multiroom OperationSemi-OSD Settings InstallationMultiroom Operation Multiroom SetupMultiroom Operation If the Remote IR Output jackTuner Operation Basic Tuner OperationRDS Display Options RDS TuningRDS Operation Program Search PTYTurn on the unit you wish to program into the AVR remote Programming the Remote with CodesDirect Code Entry Must be repeated firstProgramming the Remote Code ReadoutMacro Programming Volume Punch-Through Programmed Device FunctionsChannel Control Punch-Through Resetting the Remote Memory Function List SPLAVR DVD Power Switch 1 is pushed Troubleshooting GuideProcessor Reset Remote sensor ¯ is obscuredTechnical Specifications Harman Consumer International

AVR507 specifications

The Harman-Kardon AVR507 is a distinguished audio/video receiver that stands out in the realm of home entertainment systems. Launched in the early 2000s, the AVR507 quickly gained a reputation for its powerful performance, elegant design, and advanced feature set.

At the heart of the AVR507 is its robust amplifier section, delivering a substantial output power of 70 watts per channel across seven channels. This ensures immersive surround sound experiences that bring movies, music, and games to life with clarity and depth. The receiver supports various surround sound formats, including Dolby Digital and DTS, enabling users to enjoy cinematic audio quality right in their living room.

One of the key highlights of the AVR507 is its remarkable multi-zone capabilities. Users can setup different audio zones throughout their home, making it possible to play distinct audio sources in separate areas. This can be especially beneficial for larger homes or entertaining spaces where various preferences for music or audio may exist.

The AVR507 also boasts a comprehensive suite of connectivity options. With multiple HDMI inputs, component video, and optical audio inputs, it accommodates a wide range of devices, from Blu-ray players to gaming consoles. It also features an integrated AM/FM tuner, allowing users to enjoy their favorite radio stations without the need for additional equipment.

In terms of user experience, the receiver employs an intuitive on-screen graphical user interface, facilitating easy navigation through menus and settings. The included remote control offers convenient access to all of the AVR507's features, making for a smooth and user-friendly operation.

Another noteworthy technology within the AVR507 is its built-in digital signal processing (DSP), which enhances audio playback by optimizing sound quality based on the specific setup and speaker configuration. This ensures that whether you are watching a high-octane action film or listening to a subtle acoustic track, the audio remains balanced and rich.

The AVR507 also incorporates high-quality DACs (digital-to-analog converters) that are crucial for exceptional audio fidelity. The result is a receiver that not only excels in power and performance but also provides a refined listening experience.

In summary, the Harman-Kardon AVR507 is a versatile and powerful audio/video receiver that embodies a blend of advanced technology, user-centric design, and superb performance. Its multitude of features makes it an excellent choice for anyone looking to elevate their home entertainment experience.
Top Page Image Contents