Harman-Kardon AVR507 Tape Recording, Output Level Adjustment With Source Signals, Night Mode

Page 33

Operation

sense changes to the bitstream and channel count and reflect them in these indicators.

Important Note: When a digital surround source (Dolby Digital, DTS) is played, the letters SBL/SBR for the Surround Back channels will appear only when a DTS ES DISCRETE 6.1 source is played. Then this surround mode will be indi- cated in the front display and on-screen display. With all other recordings the icons for the sur- round back speakers may light (when those speakers have been configured) to indicate that a signal will be fed to them (Matrix decoded with NEO:6, LOGIC 7 or 7 CH Stereo), but no letters inside will light as the unit will not receive an input signal for the surround back channels.

The letters used by the Speaker/Channel Input Indicators $ also flash to indicate when a bit- stream has been interrupted. This will happen when a digital input source is selected before the playback starts, or when a digital source such as a DVD is put into a Pause mode. The flashing indicators remind you that the playback has stopped due to the absence of a digital signal and not through any fault of the AVR. This is normal, and the digital playback will resume once the playback is started again.

Night Mode

A special feature of Dolby Digital is the Night mode, which enables Dolby Digital input sources to be played back with full digital intelligibilty while reducing the maximum peak level and lifting the low levels by 1/4 to 1/3. This prevents abruptly loud transitions from disturbing others without reducing the impact of the digital source. The Night mode is available only when the Dolby Digital mode is selected.

The Night mode may be engaged when a Dolby Digital DVD is playing by pressing the Night Button Bon the remote. Next, press the ⁄/¤ buttons Dto select either the middle range or full compression versions of the Night mode. To turn the Night mode off, press the ⁄/¤ buttons

Duntil the message in the lower third of the video display and the Main Information Display ˜ reads D-RANGE OFF.

The Night mode may also be selected to always be on as soon as the Dolby Digital mode is activated at either level of compression using the options in the DOLBY menu. See page 24 for information on using the menus to set this option.

IMPORTANT NOTES ON DIGITAL PLAYBACK:

•When the digital playback source is stopped, or in a pause, fast forward or chapter search mode, the digital audio data will momentarily stop, and the channel position letters inside the Speaker/ Channel Indicators $ will flash. This is nor- mal and does not indicate a problem with either the AVR or the source machine. The AVR will

return to digital playback as soon as the data is available and when the machine is in a standard play mode.

•Although the AVR will decode virtually all DVD movies, CDs and HDTV sources, it is possible that some future digital sources may not be compatible with the AVR.

•Note that not all digitally encoded programs and not all audio tracks on a DVD contain full

5.1 or 6.1 channel audio. Consult the program guide that accompanies the DVD or laser disc to determine which type of audio has been record- ed on the disc. The AVR will automatically sense the type of digital surround encoding used, indicate it in the Channel Input Indicators $ and adjust to accommodate it.

•When a Dolby Digital or DTS source is playing, you normally may not be able to select some of the analog surround modes such as Dolby Pro Logic II, Dolby 3 Stereo, Hall, Theater, 5CH/7CH Stereo or Logic 7, except with specific Dolby Digital 2.0 recordings that can be played with the Pro Logic II modes too (see page 31).

•When a digital source is playing, it is possible to make an analog recording using the Tape

or Video 1 or Video 2 or record outputs, even if the source is connected to any digital input of the AVR only, as long as "Surround Off" mode is selected (possible with a PCM source only). But the analog two channel signal, even of a Dolby Digital (not DTS) source, the ”Downmix” to Stereo or Dolby Surround, can be recorded by connecting its analog audio outputs to the appropriate analog inputs (e.g. DVD) of the AVR. Additionally, the digital signals will be passed through to the Digital Audio Outputs .

Tape Recording

In normal operation, the audio or video source selected for listening through the AVR is

sent to the record outputs. This means that any program you are watching or listening to may be recorded simply by placing machines connected

to the outputs for Tape Outputs

or Video 1

or 2 Outputs

in the record mode.

When a digital audio recorder is connected to any of the Digital Audio Outputs , you are able to record the digital signal using a CD-R, MiniDisc or other digital recording system. Note that all digital signals will be passed through to both, coaxial and optical, digital outputs simultanously, no matter which kind of digital input was selected.

NOTES:

•The digital outputs are active only when a digital signal is present, and they do not convert an ana- log input to a digital signal, or change the format of the digital signal (e.g. Dolby Digital to PCM or vice versa, but coaxial digital signals are converted

to optical signals and vice versa). In additon, the digital recorder must be compatible with the output signal. For example, the PCM digital output from a CD player may be recorded on a CD-R or MiniDisc, but Dolby Digital or DTS signals may not.

•To make an analog recording from a digital source is possible, but only from a PCM source (not Dolby Digital or DTS) and correctly only with "Surround Off" mode (with any Surround mode only the L/R front signals will be fed to the record outputs).

Output Level Adjustment

With Source Signals

Normal output level adjustment for the

AVR is established using the test tone, as out- lined on page 24. In some cases, however, it may be desirable to adjust the output levels using program material such as a test disc, or a selec- tion you are familiar with. Additionally, the out- put level for the subwoofer and those for the Stereo and VMAx modes can only be adjusted using this procedure. Note that all adjustments made with any input will be effective with all inputs selected, just as it is the case with the adjustment using the test tone.

To adjust the output levels using program materi- al, first select the surround mode for which you want to trim the speakers (see NOTE below), start your program material source and set the reference volume for the front left and front right

channels using the Volume Control

î.

Once the reference level has been set, press the Channel Select button CÙ and note that FRONT L LEVEL will appear in the Main Information Display ˜. To change the level, first press the Set button F@, and then use the Selector buttons 7 or the ⁄/ ¤ buttons

Dto raise or lower the level. DO NOT use the volume control, as this will alter the reference setting.

Once the change has been made, press the Set button F@ and then press the Selector but- tons 7 or the ⁄/¤ buttons Dto select the next output channel location that you wish to adjust. To adjust the subwoofer level, press the Selector buttons 7 or the ⁄/¤ buttons D until WOOFER LEVEL appears in the Main Information Display ˜or on-screen display (only available if the subwoofer is turned on).

Press the Set button F@when the name of the desired channel appears in the Main Information Display ˜ and on-screen display, and follow the instructions shown above to adjust the level.

OPERATION 33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents AVR507 Limited Edition Audio/Video Receiver Declaration of Conformity Table of ContentsDescription and Features IntroductionFront panel analog A/V inputs Safety Information Important Safety InformationUnpacking Front Panel Controls # Preset Stations Selector Press this Digital Input Selector When playing aInformation on digital audio Digital Audio Outputs Connect these Rear Panel Connections+ and negative terminals Unswitched OutletMain Remote Control Functions See page 32 for more information Channel/8 Channel Direct InputMovies ∆ Play Forward/Reverse/Stop ˚ Mute Zone II Remote Control FunctionsInstallation and Connections Audio Equipment ConnectionsVideo Equipment Connections Video Input jacks Scart A/V ConnectionsVideo Connection Notes Important Note for Adapter CablesImportant Note for the Use SCART-Cinch Adapters If you use a unit providing RGB signals on aMain Room Remote Control Extension System and Power ConnectionsAC Power Connections Multiroom IR LinkSpeaker Selection Speaker PlacementUsing the On-Screen Display System ConfigurationSystem Setup First Turn OnInput Setup Speaker SetupSet Button Fto bring up the Speaker Setup menu Figure Surround Within five seconds, either press the ‹/› buttons Surround Setup Or 6.1/7.1 speaker output configuration is in use¤ Button Dso that the cursor is next to Stereo-Direct Bypass Mode Configuring the Surround Off Stereo ModesStereo-Digital Mode Delay SettingsOutput Level Adjustment Night Mode SettingsUsing EzSet Speaker/Channel IndicatorsSo that on is highlighted Sensor and Indicator off Up the Volume until you can hear the test noise clearlyWhen all channels have the same output level Operation Surround Mode ChartMix of the in-phase material of the left and right channels No delay availableNo surround channels But no surround speakersBasic Operation Source SelectionChannel/8-Channel Direct Input Volume Up/Down Buttons Surround Mode SelectionDolby Digital Digital Audio PlaybackPCM Audio Playback Selecting a Digital SourceDigital Bitstream Indicators Surround Mode TypesAudio, while the main feature is available PCM Playback IndicationsNight Mode Output Level Adjustment With Source SignalsNormal output level adjustment for Tape RecordingIndicator Select Memory BackupIndicator off Select to activate the sensorTurn On Volume Level Advanced FeaturesDisplay Brightness Surround Back/Multiroom SpeakerSemi-OSD Settings Advanced Features / Multiroom OperationFull-OSD Time Out Adjustment InstallationMultiroom Operation Multiroom SetupMultiroom Operation If the Remote IR Output jackBasic Tuner Operation Tuner OperationRDS Operation RDS TuningRDS Display Options Program Search PTYDirect Code Entry Programming the Remote with CodesTurn on the unit you wish to program into the AVR remote Must be repeated firstProgramming the Remote Code ReadoutMacro Programming Volume Punch-Through Programmed Device FunctionsChannel Control Punch-Through Resetting the Remote Memory SPL Function ListAVR DVD Processor Reset Troubleshooting GuidePower Switch 1 is pushed Remote sensor ¯ is obscuredTechnical Specifications Harman Consumer International

AVR507 specifications

The Harman-Kardon AVR507 is a distinguished audio/video receiver that stands out in the realm of home entertainment systems. Launched in the early 2000s, the AVR507 quickly gained a reputation for its powerful performance, elegant design, and advanced feature set.

At the heart of the AVR507 is its robust amplifier section, delivering a substantial output power of 70 watts per channel across seven channels. This ensures immersive surround sound experiences that bring movies, music, and games to life with clarity and depth. The receiver supports various surround sound formats, including Dolby Digital and DTS, enabling users to enjoy cinematic audio quality right in their living room.

One of the key highlights of the AVR507 is its remarkable multi-zone capabilities. Users can setup different audio zones throughout their home, making it possible to play distinct audio sources in separate areas. This can be especially beneficial for larger homes or entertaining spaces where various preferences for music or audio may exist.

The AVR507 also boasts a comprehensive suite of connectivity options. With multiple HDMI inputs, component video, and optical audio inputs, it accommodates a wide range of devices, from Blu-ray players to gaming consoles. It also features an integrated AM/FM tuner, allowing users to enjoy their favorite radio stations without the need for additional equipment.

In terms of user experience, the receiver employs an intuitive on-screen graphical user interface, facilitating easy navigation through menus and settings. The included remote control offers convenient access to all of the AVR507's features, making for a smooth and user-friendly operation.

Another noteworthy technology within the AVR507 is its built-in digital signal processing (DSP), which enhances audio playback by optimizing sound quality based on the specific setup and speaker configuration. This ensures that whether you are watching a high-octane action film or listening to a subtle acoustic track, the audio remains balanced and rich.

The AVR507 also incorporates high-quality DACs (digital-to-analog converters) that are crucial for exceptional audio fidelity. The result is a receiver that not only excels in power and performance but also provides a refined listening experience.

In summary, the Harman-Kardon AVR507 is a versatile and powerful audio/video receiver that embodies a blend of advanced technology, user-centric design, and superb performance. Its multitude of features makes it an excellent choice for anyone looking to elevate their home entertainment experience.
Top Page Image Contents