Harman-Kardon AVR507 Multiroom Operation, Multiroom Setup, If the Remote IR Output jack

Page 37

Multiroom Operation

Multiroom Setup

Once the audio and IR link connections have been made, the AVR needs to be configured for multiroom operation using the steps below. Press the OSD button Lto bring the MAS- TER MENU (Figure 1) to the screen. Press the ⁄ button Dtwice, until the on-screen › cursor is next to the MULTI-ROOMline. Press the Set button Fto enter the MULTI-ROOMmenu (Figure 12).

*

M U L T I - R O O M *

 

 

M U L T I - R O O M :

O F F

O N

M U L T I I N

: F M P R E S E T 0 1

M U L T I

V O L

:

 

 

B A C K

T O M A S T E R

M E N U

Figure 12

When the MULTI-ROOMmenu appears, the on-screen › cursor will be at the MULTI- ROOM line. Since this line is used to turn the system on and off, do not make an adjustment here unless you wish to turn the system on at this time. To turn the system on, press the › but-

ton so that ON is highlighted. If you do not wish to turn the system on at this time or to pro- ceed to the next step, press the ¤ Button D once so that the › on-screen cursor is next to the MULTI IN line.

At the MULTI IN line, press the ‹/› buttons

Euntil the desired Audio/Video input to the multi-room system appears in the highlight- ed video. When the selection has been made, press the ¤ button Donce so that the › on- screen cursor is next to the MULTI VOL line.

At the MULTI VOL line, press the ‹/ › but- tons E or hold them pressed until the desired volume level for the multi-room system is entered. DO NOT use the regular volume con- trol knobs for this setting. When all settings for the multiroom setup have been made, press the

¤buttons Donce so that the on-screen › cursor is next to the BACK TO MASTER MENU line and press the Set button F. If you have no other adjustments to make, press the OSD button Lto exit the menu system.

Multiroom Operation

When operating the AVR from a remote room location where an IR sensor link has been con- nected to the AVR’s rear panel Multiroom IR Input , you may use either the Main remote control or the Zone II remote. To turn on the multiroom feed, press any of the Input Selector buttons on the Zone II remote ∫ç∂ or the Main remote 456. Press the AVR Selector 5∫ to turn the unit on to the last source, or any of the other Selector buttons to turn on to a specific source.

As long as an IR feed to the AVR has been established from the remote room, using any of the buttons on either remote will control the remote location volume î, change the tuner frequency Kè, change the tuner

preset

© or mute the output

˚.

If the Remote IR Output jack

on the

AVR is connected to an IR Input jack on compat- ible Harman Kardon audio components such as CD, DVD or cassette players, the transport func- tions of those machines may also be controlled using the Transport Controls

PɃ©˙∆ on either remote

control.

To turn the system off from the remote room, press the Power-Offbutton 0å. Remember that the AVR may be turned on or off from the remote room regardless of the system’s operation or status in the main room.

NOTE: When the tuner is selected as the source for the remote zone, any change to the frequen- cy or preset will also change the station being listened to in the main room, if the tuner is in use there. Similarly, if someone in the main room changes the station, the change will also impact the remote room.

To activate the feed to the remote room, press

the Multiroom button on the remote. Next, press the Set button F. Press the ⁄/ ¤ buttons Dto turn the multiroom feed on or off. When the multiroom system is on, the Main Information Display ˜ or OSD will display MULTI ON. Press the Set button Ftwice to enter the setting.

When the multiroom system is turned on, the input selected using the Multiroom Menu will be fed to the Multiroom Output jacks on the rear panel. The volume will be as set in the same menu, although it may also be adjusted using an optional IR sensor and the Zone II remote in the remote location or on the optional audio power amplifier connected to the Multiroom Output jacks .

Once the multiroom system is turned on, it will remain on even if the AVR is placed in the Standby mode in the main room by pressing the Power Off Button 0or the System Power Control 2on the front panel. To turn off the multiroom system from the main listening room, when the AVR is on press the Multiroom but-

ton

and then the Set button F. Press the

⁄/ ¤ buttons D so that the Main Information Display ˜ or OSD will display

MULTI OFF.

Even when the AVR is turned off (to Standby mode) and the multiroom system is turned off too, the multiroom system may be turned on at any time by pressing the Multiroom button

,or any of the Selector buttons ∫ç

∂in the remote room.

MULTIROOM 37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents AVR507 Limited Edition Audio/Video Receiver Declaration of Conformity Table of ContentsIntroduction Description and FeaturesFront panel analog A/V inputs Important Safety Information Safety InformationUnpacking Front Panel Controls Digital Input Selector When playing a # Preset Stations Selector Press thisInformation on digital audio Digital Audio Outputs Connect these Rear Panel Connections+ and negative terminals Unswitched OutletMain Remote Control Functions See page 32 for more information Channel/8 Channel Direct InputMovies ∆ Play Forward/Reverse/Stop ˚ Mute Zone II Remote Control FunctionsAudio Equipment Connections Installation and ConnectionsVideo Equipment Connections Video Input jacks Scart A/V ConnectionsVideo Connection Notes Important Note for Adapter CablesImportant Note for the Use SCART-Cinch Adapters If you use a unit providing RGB signals on aMain Room Remote Control Extension System and Power ConnectionsAC Power Connections Multiroom IR LinkSpeaker Selection Speaker PlacementUsing the On-Screen Display System ConfigurationSystem Setup First Turn OnSpeaker Setup Input SetupSet Button Fto bring up the Speaker Setup menu Figure Surround Within five seconds, either press the ‹/› buttons Or 6.1/7.1 speaker output configuration is in use Surround Setup¤ Button Dso that the cursor is next to Stereo-Direct Bypass Mode Configuring the Surround Off Stereo ModesStereo-Digital Mode Delay SettingsOutput Level Adjustment Night Mode SettingsUsing EzSet Speaker/Channel IndicatorsSo that on is highlighted Up the Volume until you can hear the test noise clearly Sensor and Indicator offWhen all channels have the same output level Operation Surround Mode ChartMix of the in-phase material of the left and right channels No delay availableNo surround channels But no surround speakersSource Selection Basic OperationChannel/8-Channel Direct Input Volume Up/Down Buttons Surround Mode SelectionDolby Digital Digital Audio PlaybackPCM Audio Playback Selecting a Digital SourceDigital Bitstream Indicators Surround Mode TypesAudio, while the main feature is available PCM Playback IndicationsNight Mode Output Level Adjustment With Source SignalsNormal output level adjustment for Tape RecordingIndicator Select Memory BackupIndicator off Select to activate the sensorTurn On Volume Level Advanced FeaturesDisplay Brightness Surround Back/Multiroom SpeakerSemi-OSD Settings Advanced Features / Multiroom OperationFull-OSD Time Out Adjustment InstallationMultiroom Operation Multiroom SetupMultiroom Operation If the Remote IR Output jackBasic Tuner Operation Tuner OperationRDS Operation RDS TuningRDS Display Options Program Search PTYDirect Code Entry Programming the Remote with CodesTurn on the unit you wish to program into the AVR remote Must be repeated firstCode Readout Programming the RemoteMacro Programming Programmed Device Functions Volume Punch-ThroughChannel Control Punch-Through Resetting the Remote Memory SPL Function ListAVR DVD Processor Reset Troubleshooting GuidePower Switch 1 is pushed Remote sensor ¯ is obscuredTechnical Specifications Harman Consumer International

AVR507 specifications

The Harman-Kardon AVR507 is a distinguished audio/video receiver that stands out in the realm of home entertainment systems. Launched in the early 2000s, the AVR507 quickly gained a reputation for its powerful performance, elegant design, and advanced feature set.

At the heart of the AVR507 is its robust amplifier section, delivering a substantial output power of 70 watts per channel across seven channels. This ensures immersive surround sound experiences that bring movies, music, and games to life with clarity and depth. The receiver supports various surround sound formats, including Dolby Digital and DTS, enabling users to enjoy cinematic audio quality right in their living room.

One of the key highlights of the AVR507 is its remarkable multi-zone capabilities. Users can setup different audio zones throughout their home, making it possible to play distinct audio sources in separate areas. This can be especially beneficial for larger homes or entertaining spaces where various preferences for music or audio may exist.

The AVR507 also boasts a comprehensive suite of connectivity options. With multiple HDMI inputs, component video, and optical audio inputs, it accommodates a wide range of devices, from Blu-ray players to gaming consoles. It also features an integrated AM/FM tuner, allowing users to enjoy their favorite radio stations without the need for additional equipment.

In terms of user experience, the receiver employs an intuitive on-screen graphical user interface, facilitating easy navigation through menus and settings. The included remote control offers convenient access to all of the AVR507's features, making for a smooth and user-friendly operation.

Another noteworthy technology within the AVR507 is its built-in digital signal processing (DSP), which enhances audio playback by optimizing sound quality based on the specific setup and speaker configuration. This ensures that whether you are watching a high-octane action film or listening to a subtle acoustic track, the audio remains balanced and rich.

The AVR507 also incorporates high-quality DACs (digital-to-analog converters) that are crucial for exceptional audio fidelity. The result is a receiver that not only excels in power and performance but also provides a refined listening experience.

In summary, the Harman-Kardon AVR507 is a versatile and powerful audio/video receiver that embodies a blend of advanced technology, user-centric design, and superb performance. Its multitude of features makes it an excellent choice for anyone looking to elevate their home entertainment experience.
Top Page Image Contents