Harman-Kardon AVR507 owner manual So that on is highlighted

Page 25

System Configuration

configuration button has been pressed the test noise will be heard from the front left speaker.

6.At this point, EzSet will take over, adjusting the output level of each channel so that when the process is complete all levels will be equal and at the set reference point. This process may take a few minutes, depending on the extent of adjustment required.

7.During the adjustment, you will see the loca- tion of the channel position being adjusted appear in the on-screen display (if connected) and in the Main Information Display ˜, alternating with a readout of the output set- ting, relative to the reference volume level. As the adjustment proceeds, a few things will happen simultaneously:

•The channel position being adjusted will flash in the Speaker/Channel Input Indicators $. If the test noise is heard from a channel other than the one shown in the Indicator, the on-screen display or the front panel display, there is an error in the speaker connections. If this is the case, press the Test Button 8 TWICE to stop the adjustment. Then, turn the

unit off and verify that all speakers are con-

nected to the proper Outputs. Afterwards start the adjusting process again from the beginning.

•As the individual channels are set, the channel name and the adjustment offset will appear in the on-screen display (if connected) and the Main Information Display ˜. While the level is changing, the Program/SPL Indicator 2will change colors to reflect the output level in relation to the reference.

A red indication shows that the level is too high, while an orange indication shows that the level is too low. When the indicator is green, the level is correct, and the test noise will move to the next channel.

•While adjustments are being made, the red LED under the AVR Selector f will flash. This is normal, and indicates that EzSet is oper- ating.

8.After the test noise has circulated once through each channel, it will send the tone to each channel once again, to verify the settings.

9.After two complete circulations of the tone, the levels are set. The Program/SPL Indicator 2will remain green at each channel. Upon completion of the second circu- lation, the Program/SPL Indicator 2will flash green twice and then go out. The tone will stop and the AVR will return to normal operation.

If you find that the output levels chosen by EzSet are either much lower or much higher than the "0dB" reference setting or even at the limits of the +/-10dB variation range for the output levels, depending on the sensitivity of the speakers in use and your specific room layout, you may repeat the procedure. Return to Step 2 and adjust the master volume either higher or lower appropriately to the output levels set previously (e.g. when levels were set to about "–7dB" reduce the master volume for 7dB), to accommo- date your particular room layout and your speak- ers. You may repeat this procedure as many times as necessary to achieve a desired result. In order to prevent possible damage to your hearing or your equipment, we emphasize that you should avoid setting the master volume above 0dB.

NOTE: The subwoofer output is not adjusted when the test tone is in use. To adjust the subwoofer output you must use an external source, following the instructions on page 33.

Manual Output Level Adjustment Output levels may also be adjusted manually, either to set them to a specific level with an SPL meter, or to make fine tuning adjustments to the levels obtained using the EzSet remote.

Manual output level adjustment is most easily done through the CHANNEL ADJUST menu (Figure 8). If you are already at the main menu, press the ¤ Button Duntil the on- screen › cursor is next to the CHANNEL ADJUST line. If you are not at the main menu, press the OSD Button v to bring up the MASTER MENU (Figure 1), and then press the ¤ Button Dfour times so that the onscreen › cursor is next to the CHANNEL ADJUST line. Press the Set Button Fto bring the CHANNEL ADJUST menu (Figure 8) to the screen.

* C H A N N E L A D J U S T

*

F L

: 0 d B

S B R

:

0 d B

C E N : 0 d B

S B L

:

0 d B

F R

: 0 d B

S L

:

0 d B

S R

: 0 d B

S U B

:

0 d B

C H A N N E L R E S E T :

O F F

O N

 

 

 

 

 

T E S T T O N E

:

O F F

O N

B A C K T O M A S T E R

M E N U

Figure 8

Once the menu appears on your video screen, first use the ⁄ Button Dto move the on- screen › cursor so that it is next to the TEST TONE line. Press the ‹/ › Buttons E

so that ON is highlighted.

You will hear a test noise circulate from speaker to speaker in a clockwise direction around the room. The test noise will play for two seconds in each speaker before circulating, and a blinking on-screen cursor will appear next to the name of each speaker location when the sound is at that speaker. Now turn up the volume until you can hear the noise clearly.

IMPORTANT NOTE: Because this test noise will have a much lower level than normal music, the volume must be lowered after the adjustment for all channels is made, but BEFORE you return to the main menu and the test tone turns off.

NOTE: Remember to verify that the speakers have been properly connected. As the test noise circulates, listen to make certain that the sound comes from the speaker position shown in the Main Information Display ˜. If the sound comes from a speaker location that does NOT match the position indicated in the display, turn the AVR off using the Main Power Switch 1 and check the speaker wiring or connections to external power amplifiers to make certain that each speaker is connected to the correct output terminal.

After checking for speaker placement, let the test noise circulate again, and listen to see which channels sound louder than the others. Using the front left speaker as a reference, press the ‹/› Buttons E on the remote to bring all speakers to the same volume level. When one of the ‹/› buttons is pushed, the test noise circula- tion will pause on the channel being adjusted to give you time to make the adjustment. When you release the button, the circulation will resume after five seconds. The on-screen cursor › and the test noise can also be moved directly to the speaker to be adjusted by pressing the ⁄/¤ buttons Don the remote.

Continue to adjust the individual channels until the volume level sounds the same from each speaker. Note that adjustments should be made with the ‹/› Buttons E on the remote only, NOT the main volume controls.

If you are using a sound-pressure level (SPL) meter for precise level adjustment with the test

tone, open the main Volume Control to –15dB and set the individual output level for each channel so that the meter reads 75dB, C-Weighted Slow. After all settings are made turn the main volume down.

SYSTEM CONFIGURATION 25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents AVR507 Limited Edition Audio/Video Receiver Declaration of Conformity Table of ContentsIntroduction Description and FeaturesFront panel analog A/V inputs Important Safety Information Safety InformationUnpacking Front Panel Controls Digital Input Selector When playing a # Preset Stations Selector Press thisInformation on digital audio Digital Audio Outputs Connect these Rear Panel Connections+ and negative terminals Unswitched OutletMain Remote Control Functions See page 32 for more information Channel/8 Channel Direct InputMovies ∆ Play Forward/Reverse/Stop ˚ Mute Zone II Remote Control FunctionsAudio Equipment Connections Installation and ConnectionsVideo Equipment Connections Video Input jacks Scart A/V ConnectionsVideo Connection Notes Important Note for Adapter CablesImportant Note for the Use SCART-Cinch Adapters If you use a unit providing RGB signals on aMain Room Remote Control Extension System and Power ConnectionsAC Power Connections Multiroom IR LinkSpeaker Selection Speaker PlacementUsing the On-Screen Display System ConfigurationSystem Setup First Turn OnSpeaker Setup Input SetupSet Button Fto bring up the Speaker Setup menu Figure Surround Within five seconds, either press the ‹/› buttons Or 6.1/7.1 speaker output configuration is in use Surround Setup¤ Button Dso that the cursor is next to Stereo-Direct Bypass Mode Configuring the Surround Off Stereo ModesStereo-Digital Mode Delay SettingsOutput Level Adjustment Night Mode SettingsUsing EzSet Speaker/Channel IndicatorsSo that on is highlighted Up the Volume until you can hear the test noise clearly Sensor and Indicator offWhen all channels have the same output level Operation Surround Mode ChartMix of the in-phase material of the left and right channels No delay availableNo surround channels But no surround speakersSource Selection Basic OperationChannel/8-Channel Direct Input Volume Up/Down Buttons Surround Mode SelectionDolby Digital Digital Audio PlaybackPCM Audio Playback Selecting a Digital SourceDigital Bitstream Indicators Surround Mode TypesAudio, while the main feature is available PCM Playback IndicationsNight Mode Output Level Adjustment With Source SignalsNormal output level adjustment for Tape RecordingIndicator Select Memory BackupIndicator off Select to activate the sensorTurn On Volume Level Advanced FeaturesDisplay Brightness Surround Back/Multiroom SpeakerSemi-OSD Settings Advanced Features / Multiroom OperationFull-OSD Time Out Adjustment InstallationMultiroom Operation Multiroom SetupMultiroom Operation If the Remote IR Output jackBasic Tuner Operation Tuner OperationRDS Operation RDS TuningRDS Display Options Program Search PTYDirect Code Entry Programming the Remote with CodesTurn on the unit you wish to program into the AVR remote Must be repeated firstCode Readout Programming the RemoteMacro Programming Programmed Device Functions Volume Punch-ThroughChannel Control Punch-Through Resetting the Remote Memory SPL Function ListAVR DVD Processor Reset Troubleshooting GuidePower Switch 1 is pushed Remote sensor ¯ is obscuredTechnical Specifications Harman Consumer International

AVR507 specifications

The Harman-Kardon AVR507 is a distinguished audio/video receiver that stands out in the realm of home entertainment systems. Launched in the early 2000s, the AVR507 quickly gained a reputation for its powerful performance, elegant design, and advanced feature set.

At the heart of the AVR507 is its robust amplifier section, delivering a substantial output power of 70 watts per channel across seven channels. This ensures immersive surround sound experiences that bring movies, music, and games to life with clarity and depth. The receiver supports various surround sound formats, including Dolby Digital and DTS, enabling users to enjoy cinematic audio quality right in their living room.

One of the key highlights of the AVR507 is its remarkable multi-zone capabilities. Users can setup different audio zones throughout their home, making it possible to play distinct audio sources in separate areas. This can be especially beneficial for larger homes or entertaining spaces where various preferences for music or audio may exist.

The AVR507 also boasts a comprehensive suite of connectivity options. With multiple HDMI inputs, component video, and optical audio inputs, it accommodates a wide range of devices, from Blu-ray players to gaming consoles. It also features an integrated AM/FM tuner, allowing users to enjoy their favorite radio stations without the need for additional equipment.

In terms of user experience, the receiver employs an intuitive on-screen graphical user interface, facilitating easy navigation through menus and settings. The included remote control offers convenient access to all of the AVR507's features, making for a smooth and user-friendly operation.

Another noteworthy technology within the AVR507 is its built-in digital signal processing (DSP), which enhances audio playback by optimizing sound quality based on the specific setup and speaker configuration. This ensures that whether you are watching a high-octane action film or listening to a subtle acoustic track, the audio remains balanced and rich.

The AVR507 also incorporates high-quality DACs (digital-to-analog converters) that are crucial for exceptional audio fidelity. The result is a receiver that not only excels in power and performance but also provides a refined listening experience.

In summary, the Harman-Kardon AVR507 is a versatile and powerful audio/video receiver that embodies a blend of advanced technology, user-centric design, and superb performance. Its multitude of features makes it an excellent choice for anyone looking to elevate their home entertainment experience.
Top Page Image Contents