Harman-Kardon AVR507 owner manual Memory Backup, Select to activate the sensor, Indicator Select

Page 34

Operation

Repeat the procedure as needed until all chan- nels requiring adjustment have been set. When all adjustments have been made and no further adjustments are made for five seconds, the AVR will return to normal operation.

If you are using a disc with noise test signals or an external signal generator as the source from which to trim the output levels, you may use the EzSet feature of the remote to guide you to the correct SPL level. To use the remote for this pur- pose, start the test tone from the source and press and quickly release the SPL Indicator

Select to activate the sensor.

While the test tone is played, the Program/SPL Indicator 2will change color to indicate the level. When it is red, the level is too high; when it is orange, the level is too low. To set the refer-

ence level, open the Volume Control until the SPL Indicator´s LED lights green when the test signal is fed to the left front speaker. Then adjust the level of all other speakers, while they are receiving the test signal, until the LED lights green for all channels. After the output levels for all channels are aligned, press the SPL

Indicator Select

to turn the sensor and

indicator off.

 

The channel output may also be adjusted using the full-OSD on-screen menu system. First, set the volume to a comfortable listening level using the Volume Control ı î. Then, press the OSD button Lto bring up the MASTER MENU (Figure 1). Press the ¤ Button Dfour times until the on-screen › cursor is next to the CHANNEL ADJUST line. Press the Set Button Fto activate the CHANNEL ADJUST menu (Figure 10).

* C H A N N E L A D J U S T

*

F L

: 0 d B

S B R

:

0 d B

C E N : 0 d B

S B L

:

0 d B

F R

: 0 d B

S L

:

0 d B

S R

: 0 d B

S U B

:

0 d B

C H A N N E L R E S E T :

O F F

O N

 

 

 

 

 

T E S T T O N E

:

O F F

O N

B A C K T O M A S T E R

M E N U

 

 

 

 

 

level for each channel and surround mode as you prefer, e.g. you may lower the center channel level when you find it to be too high or increase the level of the rears when you find it to be too low with specific surround modes.

If you wish to reset all the levels to their original factory default of 0dB offset, press the ⁄/¤ Buttons Dso that the on-screen cursor is next to the CHANNEL RESET line and press the ‹/ › Buttons E so that the word ON is highlighted. After the levels are reset, resume the procedure outlined above to reset the levels to the desired settings. When all adjustments are done, press the ⁄/¤ Buttons Dto move the on-screen › cursor so that it is next to BACK TO MASTER MENU and then press the Set Button Fif you wish to go back to the main menu to make other adjustments. If you have no other adjustments to make, press the OSD Button Lto exit the menu system.

NOTE: The output levels may be separately trimmed for each digital and analog surround mode. If you wish to have different trim levels for a specific mode, select that mode and then follow the instructions in the steps shown above.

With Stereo and Vmax modes the adjustment procedure described above is the only way to trim the output level, e.g. to match the Stereo or Vmax level with other modes.

Memory Backup

This product is equipped with a memory backup system that preserves tuner presets and system configuration information if the unit is turned off completely, accidentally unplugged or subjected to a power outage. This memory will last for approximately two weeks, after which time all information must be reentered.

Figure 10

When the menu appears, the internal test tone will be turned off. This will allow you to use your external test disc or other source material as the test signal. Then, use the ⁄/¤ Buttons Dto select the channels to be adjusted. At each channel position use the ‹/ › Buttons E

to change the output level.

Remember, when you are using a disc with test signal (e.g. pink noise) or an external signal generator as the source, the goal is to have the output level at each channel be equal when heard at the listening position, with any surround mode selected. When your test source is a nor- mal disc with music signals, you may adjust the

34OPERATION

Page 33 Page 35
Image 34
Page 33 Page 35
Contents AVR507 Limited Edition Audio/Video Receiver Table of Contents Declaration of ConformityIntroduction Description and FeaturesFront panel analog A/V inputs Important Safety Information Safety InformationUnpacking Front Panel Controls Digital Input Selector When playing a # Preset Stations Selector Press thisInformation on digital audio Rear Panel Connections Digital Audio Outputs Connect theseUnswitched Outlet + and negative terminalsMain Remote Control Functions Channel/8 Channel Direct Input See page 32 for more informationMovies Zone II Remote Control Functions ∆ Play Forward/Reverse/Stop ˚ MuteAudio Equipment Connections Installation and ConnectionsVideo Equipment Connections Video Connection Notes Scart A/V ConnectionsVideo Input jacks Important Note for Adapter CablesIf you use a unit providing RGB signals on a Important Note for the Use SCART-Cinch AdaptersAC Power Connections System and Power ConnectionsMain Room Remote Control Extension Multiroom IR LinkSpeaker Placement Speaker SelectionSystem Setup System ConfigurationUsing the On-Screen Display First Turn OnSpeaker Setup Input SetupSet Button Fto bring up the Speaker Setup menu Figure Surround Within five seconds, either press the ‹/› buttons Or 6.1/7.1 speaker output configuration is in use Surround Setup¤ Button Dso that the cursor is next to Stereo-Digital Mode Configuring the Surround Off Stereo ModesStereo-Direct Bypass Mode Delay SettingsUsing EzSet Night Mode SettingsOutput Level Adjustment Speaker/Channel IndicatorsSo that on is highlighted Up the Volume until you can hear the test noise clearly Sensor and Indicator offWhen all channels have the same output level Surround Mode Chart OperationNo surround channels No delay availableMix of the in-phase material of the left and right channels But no surround speakersSource Selection Basic OperationChannel/8-Channel Direct Input Surround Mode Selection Volume Up/Down ButtonsPCM Audio Playback Digital Audio PlaybackDolby Digital Selecting a Digital SourceAudio, while the main feature is available Surround Mode TypesDigital Bitstream Indicators PCM Playback IndicationsNormal output level adjustment for Output Level Adjustment With Source SignalsNight Mode Tape RecordingIndicator off Memory BackupIndicator Select Select to activate the sensorDisplay Brightness Advanced FeaturesTurn On Volume Level Surround Back/Multiroom SpeakerFull-OSD Time Out Adjustment Advanced Features / Multiroom OperationSemi-OSD Settings InstallationMultiroom Operation Multiroom SetupMultiroom Operation If the Remote IR Output jackTuner Operation Basic Tuner OperationRDS Display Options RDS TuningRDS Operation Program Search PTYTurn on the unit you wish to program into the AVR remote Programming the Remote with CodesDirect Code Entry Must be repeated firstCode Readout Programming the RemoteMacro Programming Programmed Device Functions Volume Punch-ThroughChannel Control Punch-Through Resetting the Remote Memory Function List SPLAVR DVD Power Switch 1 is pushed Troubleshooting GuideProcessor Reset Remote sensor ¯ is obscuredTechnical Specifications Harman Consumer International

AVR507 specifications

The Harman-Kardon AVR507 is a distinguished audio/video receiver that stands out in the realm of home entertainment systems. Launched in the early 2000s, the AVR507 quickly gained a reputation for its powerful performance, elegant design, and advanced feature set.

At the heart of the AVR507 is its robust amplifier section, delivering a substantial output power of 70 watts per channel across seven channels. This ensures immersive surround sound experiences that bring movies, music, and games to life with clarity and depth. The receiver supports various surround sound formats, including Dolby Digital and DTS, enabling users to enjoy cinematic audio quality right in their living room.

One of the key highlights of the AVR507 is its remarkable multi-zone capabilities. Users can setup different audio zones throughout their home, making it possible to play distinct audio sources in separate areas. This can be especially beneficial for larger homes or entertaining spaces where various preferences for music or audio may exist.

The AVR507 also boasts a comprehensive suite of connectivity options. With multiple HDMI inputs, component video, and optical audio inputs, it accommodates a wide range of devices, from Blu-ray players to gaming consoles. It also features an integrated AM/FM tuner, allowing users to enjoy their favorite radio stations without the need for additional equipment.

In terms of user experience, the receiver employs an intuitive on-screen graphical user interface, facilitating easy navigation through menus and settings. The included remote control offers convenient access to all of the AVR507's features, making for a smooth and user-friendly operation.

Another noteworthy technology within the AVR507 is its built-in digital signal processing (DSP), which enhances audio playback by optimizing sound quality based on the specific setup and speaker configuration. This ensures that whether you are watching a high-octane action film or listening to a subtle acoustic track, the audio remains balanced and rich.

The AVR507 also incorporates high-quality DACs (digital-to-analog converters) that are crucial for exceptional audio fidelity. The result is a receiver that not only excels in power and performance but also provides a refined listening experience.

In summary, the Harman-Kardon AVR507 is a versatile and powerful audio/video receiver that embodies a blend of advanced technology, user-centric design, and superb performance. Its multitude of features makes it an excellent choice for anyone looking to elevate their home entertainment experience.
Top Page Image Contents