Briggs & Stratton 073004 WP15-225 Using the Water Pump, Safe Operating Considerations

Page 8

OPERATION

USING THE WATER PUMP

WARNING

Running water pump gives off carbon monoxide, an odorless, colorless, poison gas.

Breathing carbon monoxide may cause nausea, fainting or death.

•Operate water pump ONLY outdoors.

•Keep exhaust gas from entering a confined area through windows, doors, ventilation intakes or other openings.

•DO NOT operate water pump inside any building, confined area or enclosure, such as basements, garages or a similar location, even if doors or windows are open.

Safe Operating Considerations

Clearances and Air Movement

WARNING

Exhaust heat/gases can ignite combustibles, structures or damage fuel tank causing a fire.

•Keep at least 5 ft. (152 cm) clearance on all sides of water pump including overhead.

DO NOT place water pump where exhaust gas could accumulate and enter inside or be drawn into a potentially occupied building. Ensure exhaust gas is kept away from any windows, doors, ventilation intakes or other openings that can allow exhaust gas to collect in a confined area (Figure 5). Prevailing winds and air currents should be taken into consideration when positioning water pump.

Figure 5 — Water Pump Clearance

Typical Water Pump Shown

Exhaust Port

What is “Head”?

Head refers to the height of a column of water that can be delivered by the discharge of the pump.

Suction Head is the vertical distance between the center of the pump and the surface of the liquid on the suction side of the pump. May also be referred to as “suction lift”.The atmospheric pressure of 14.7 psi at sea level limits suction head lift to less than approximately 26 feet for any pump.

Discharge Head is the vertical distance between the pump’s discharge port and the point of discharge, which is the liquid surface if the hose is submerged or pumping into the bottom of a tank.

Total Head is the sum of the suction head value plus the discharge head value.

As water pumping height increases, pump output decreases. The length, type, and size of the suction and discharge hoses can also significantly affect pump output.

It is important for the suction operation to be the shorter part of the total pumping action.This will decrease the priming time and improve pump performance by increasing the discharge head.

Suction head is a maximum of 25 feet and discharge head should be a maximum of 200 feet.Total head can not be more than 225 feet (Figure 6, next page).

Move Water Pump to Safe

Operating Location

For best pump performance, locate the pump on a flat, level surface as close as possible to the water to be pumped. Secure water pump to avoid tipover. Use hoses that are no longer than necessary.

IMPORTANT: Direct open end of discharge hose away from home, electrical devices or anything not desired to get wet.

WARNING

Fuel and its vapors are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

WHEN OPERATING EQUIPMENT

•This water pump is not for use in mobile equipment or marine applications.

•DO NOT tip engine or equipment at angle which causes fuel to spill.

•Secure water pump. Loads from hoses may cause tipover.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Model Equipment Description Table of ContentsSafety Rules Unintentional sparking can result in fire or electric shock Operate water pump only outdoorsSafety Rules Engine Speed Lever Used to adjust engine speed to Know Your Water PumpEngine Information not shown Stamped on valve Strainer Basket not shown Used to limit passageAssembly Carton ContentsUnpack Water Pump Add Engine OilAttach Suction Hose Attach Discharge HoseAttach Suction Hose to Pump Attach Suction Hose to Strainer BasketUsing the Water Pump What is Head?Safe Operating Considerations Move Water Pump to Safe Operating LocationPrime the Water Pump Locate Strainer Basket Into Water SourceStarting the Water Pump Choke Lever shown in Choke positionStopping the Water Pump Drain and Flush Water PumpProduct Specifications Power RatingsEngine Technical Information ModelMaintenance Schedule MaintenanceCleaning General RecommendationsOil Oil RecommendationsChecking Oil Level Adding Engine OilService Spark Plug Service Air CleanerTo service the air cleaner, follow these steps Oil Fill OpeningClean Spark Arrester Screen Air Cooling SystemStorage Long Term Storage InstructionsWater Pump Other Storage TipsTroubleshooting Problem Cause CorrectionPage Emissions Control System Warranty Owner’s Warranty ResponsibilitiesPage Page Limited Warranty Table DES Matières Description DE LéquipementMise EN Garde Règles DE SécuritéLors DU Réglage OU DES Réparations DE Votre Pompe À EAU Avertissement Étiquette du numéro de série Connaître Votre Pompe À EAUOrifices dévacuation Assemblage Déballage de la pompe à eauContenu de la boîte Ajout de lhuile à moteurFixation du boyau daspiration Fixation du boyau dévacuationFixation du boyau daspiration à la pompe Fixation du boyau daspiration au panier-filtreDéplacement de la pompe vers un emplacement sécuritaire Utilisation DE LA Pompe À EAU AvertissementPour un fonctionnement sécuritaire Quest-ce que la hauteur?Amorçage de la pompe à eau Localisation du panier-filtre dans la source deauLinterrupteur est illustré en position On Démarrage de la pompe à eauPoussez linterrupteur ON/OFF sur On Figure Arrêt de la pompe à eau Vidange et rinçage de la pompe à eauRenseignements Techniques SUR LE Moteur Caractéristiques DU ProduitPuissance nominale ModèleRecommandations générales Calendrier DentretienContrôle des émissions EntretienRecommandations relatives à l’huile HuileVérification du niveau dhuile Ajout d’huileEntretien du filtre à air Entretien de la bougie dallumageCartouche Base CouvercleNettoyage de lécran pare-étincelles Système de refroidissement à airEntreposage Directives dentreposage à long termePompe à eau Autres conseils dentreposageProblèm Cause Solution DépannageGarantie DU Dispositif Antipollution Page Garantie Limitée Índice Descripción DEL EquipoPrecaución Normas DE SeguridadCuando Pruebe LA Bujía DEL Motor Quemaduras severas pueden ocurrir al hacer contacto Conozca SU Bomba DE Agua Depósito de combustibleMontaje Desembalaje de la bomba de aguaContenido de la caja Añadir aceite del motor Añadir combustibleFijación de la manguera de aspiración Conexión de la manguera de descargaConexión de la manguera de aspiración a la bomba Conexión de la manguera a la cesta del filtroUSO DE LA Bomba DE Agua Advertencia Consideraciones para un uso seguroColocación de la bomba de agua en una posición segura Espacio libre y circulación de aireVuelva a colocar el tapón de la bomba Cebado de la bomba de aguaColocación de la cesta del filtro en la fuente de agua Puesta en marcha de la bomba de agua RápidoEstrangular FuncionamientoParada de la bomba de agua Vaciado y limpieza de la bomba de aguaInformación Técnica Sobre EL Motor Especificaciones DEL ProductoPotencia nominal ModeloPlan DE Mantenimiento Recomendaciones generalesControl de emisiones MantenimientoAceite Recomendaciones sobre el aceiteComprobación del nivel de aceite Adición de aceite del motorPara revisar el filtro de aire, siga estos pasos Revisión del filtro de aireRevisión de la bujía Limpieza de la pantalla apagachispas Sistema de refrigeración de aireAlmacenamiento Instrucciones de almacenamiento a largo plazoBomba de agua Otras sugerencias para el almacenamientoResolución DE Problemas Problema Motivo SoluciónNotas Garantía DEL Sistema DE Control DE Emisiones = 250 horas, B = 500 horas y a = 1000 horas Uso del consumidor Uso comercial

073004 WP15-225 specifications

The Briggs & Stratton 073004 WP15-225 is a powerful and efficient water pump designed to tackle a variety of dewatering tasks. Engineered with durability and performance in mind, this pump is ideal for homeowners, contractors, and outdoor enthusiasts looking for a reliable solution for managing water removal from puddles, flooded basements, or construction sites.

At the heart of the WP15-225 is a robust 225cc Briggs & Stratton engine that generates ample power to move large volumes of water quickly. With a pumping capacity of up to 3,000 gallons per hour, it can handle substantial dewatering projects with ease. The engine is designed for easy starting, thanks to the reliable recoil start system, ensuring that users can get to work without delays.

One of the standout features of the WP15-225 is its cast iron volute and impeller, which provide superior durability and resistance to corrosion. This construction not only extends the lifespan of the pump but also enhances its efficiency during operation. The pump is capable of lifting water from depths of up to 25 feet, making it an effective solution for a range of applications.

The WP15-225 also includes a user-friendly design with ergonomic handles for easy transportation, coupled with a lightweight frame that makes it convenient to move around job sites. The integrated transport kit allows users to maneuver the pump effortlessly, delivering convenience on the go.

Furthermore, the pump features a durable, large-capacity fuel tank that ensures extended operation between refueling, minimizing downtime for the user. Its adjustable discharge feature allows for versatile operation, accommodating different discharge hose sizes and lengths, which is particularly useful for varying project requirements.

Safety features are not overlooked; the pump includes a low-oil shutdown mechanism that protects the engine from damage, ensuring longevity and reliable performance. The design has been tailored to minimize vibration, resulting in reduced user fatigue during extended use.

In summary, the Briggs & Stratton 073004 WP15-225 is a reliable, high-performing water pump that combines powerful engineering with user-friendly features. With its robust construction, efficient pumping capability, and thoughtful design elements, it stands out as a top choice for anyone in need of an effective solution for water management tasks. Whether it's for residential or commercial use, the WP15-225 is built to meet the demands of any dewatering challenge.
Top Page Image Contents