Electrolux EOG 660 manual Fitting the Appliance and Cabinet

Page 40

INSTALLATION Flexible Pipe Installation.

FITTING THE APPLIANCE AND CABINET

It is recommended that a 3/8" 1100mm long angle bayonet flexible hose (B.F.S.) and a ½" straight socket (B.F.S.) be used for the installation. However any approved hose of the correct length can be used. IMPORTANT: Flexible tubing used must comply with BS 669 current editions. L.P.G. flexible connections must be of a type suitable for L.P.G. and capable of operation up to 50mbar and carry a red stripe, band or label.

NOTE: Only liquid sealants can be used in threaded gas connections. Do not use P.T.F.E. tape.

1Make suitable arrangements for gas and electric supplies into the installation site. Preferably a junction box or a 3 pin earthed socket should be situated at the back of the cabinet below the oven.

2The electrical connection to the appliance is at the rear bottom right hand side; the junction box or socket should be positioned accordingly.

3Fit the cabinet as Fig.1, make sure that it is level.

4When unpacking the appliance keep it on it's polystyrene base until it is put into the cabinet to avoid damage.

NOTE: It is imperative that the appliance is left in the base to protect both the appliance and the floor. Do not allow young children to play with any part of the packaging.

5Remove the oven door. (See section B on page 44). Remove the fascia panel. (See section A on page 43).

6If the gas supply bayonet and wall fixing bracket are to be located behind the appliance it must be located in the shaded area as indicated in Fig.3.

7Connect flexible hose to the gas inlet supply block see Fig.3 . The hose should be long enough to allow the appliance to be withdrawn from the cabinet.

8Position the appliance in front of the cabinet and run the supply cable (See Section 2) through the cabinet and connect to the junction box or socket. Ensure that the supply is isolated at this stage. Connect

flexible hose to the bayonet connector.

N.B. Two people will be required to carry out the lifting procedure.

Warning: Do not attempt to lift this appliance by the handle.

9Lift the appliance into the cabinet making sure the hose and cable are not trapped. Push the appliance as far back as it will go.

10Centralise and fix the appliance using the four wood screws provided, in the position indicated in Fig.2. NOTE: If fitting the cabinet heat deflectors they should be located behind the front frame and secured in

position by the above four wood screws.

11Carry out gas soundness check.

NOTE: Check gas supply pressure before fitting fascia (See SECTION 3).

FIG.2

HEAT DEFLECTOR

FIXING

POINTS

40

Page 39 Page 41
Image 40
Page 39 Page 41
Contents ModelEOG660 Introduction For your safetyG 6 6 Contents Installing the oven For your safety Cabinet DimensionsLocation For further details seeGeneral information Cooling fan for the controlsConnecting to the electricity supply IgnitionOven light Please noteLighting the oven/grill GrillOven To lightTo turn off any burner Lighting the oven/grill G 6 6Grill Grill gives variable heat settingsHeat control Cooking positions PreheatingPutting food on the grid Grill shelfFor your safety Grill pan and handle Grill pan is supplied with a removable handlePlate warming Oven For your safety Heat zonesOven shelves Roasting Baking trays and dishes For your safetyCondensation Oven cooking chart Mins. per ½ kg 1 lb and 25 mins Mins. per ½ kg 1 lb and 15 minsFor each ½kg 1lb Large Mins Individual CakesBread 0.45kg 1lb loaves Food preparation slow cooking Slow cookingJoints of meat and poultry G 6 6 Soups, casseroles and stews VegetablesMilk puddings Frozen foodsG 6 6 Milk and milk products, for example cream ReheatingElectronic timer Electronic timerTo set the time of day To use the minute minderElectronic timer G 6 6 Setting the controls for automatic useAutomatic control To cancel an automatic programme Hints and tips for automatic cooking Care and cleaning For your safety Cleaning the brass plated handles and controlOven Oven cleaning cycle Cleaning between the outer and inner door glassTo remove the outer glass You can remove the glass from the oven door if you need toCleaning The Door Glass Rust removers Bath/Sink stain removersWhat is wrong and why? ProblemCheck LCheckG 6 6 Problem Replacing an oven light bulb Replacing an ovenlight bulbService and spare parts 7 0 5 9 2 9 9 2Customer Care Department Installation Instructions Technical Data Important Safety Requirements Provision for VentilationLocation of Appliance Min 570 maxFitting the Appliance and Cabinet 500 Connection to Electricity Supply Green and YellowRE-ASSEMBLE the Appliance Pressure TestingRemoval of Fascia Panel Removal of Oven Door Checking the GrillTo SET the Time of DAY Checking the Main OvenAutomatic Operation General NoteGuarantee Conditions Standard guarantee conditionsContents Check List Telephone 0870 5 Electrolux Household Appliances Limited
Top Page Image Contents