Electrolux 60820 manual Start the Wash Programme, Changing/Interrupting/Cancelling

Page 25

Operating Instructions

Start the Wash Programme

0 1. Check that when the dishes and cutlery are loaded into the dishwasher the spray arms are free to rotate.

2.Open the tap fully.

3.Shut the door.

4.Press the ON/OFF button. The ON/OFF button indicator illuminates.

5.Press the programme button for the desired programme (see "Pro- gramme Table"). The programme indicator illuminates. The selected programme begins after around 6 seconds. The time remaining until the end of the programme is displayed on the multi-display, the time calculated is dependent on the load in the dish racks.

With automatic programme adjustment this residual time count can be stopped or corrected if necessary (load quantity, degree of dirtiness, etc.) using the dishwasher control.

3	If fault messages are displayed on the multi-display after the start of
	the programme, please read the "What to do, if..." section.
	Changing/Interrupting/Cancelling
	the Wash Programme
3	Only change or interrupt a wash programme in progress if it is abso-
	lutely necessary to do so.
	Changing the wash programme
3	If you want to change the wash programme within 6 seconds of mak-
	ing a programme selection, briefly press the button for the new wash
	programme.
	If you want to change the wash programme at a later point in time, use
	the following procedure:

0 1. Press the button for the new wash programme and hold it pressed. The indicators for both programmes now flash.

2.After a few seconds only the indicator for the new programme flashes. Release the programme button, the new programme is now running.

Interrupting the wash programme by opening the door of the dishwasher

1Hot steam may escape from the appliance when opening the door. Open the door carefully.

25

Image 25

Contents Favorit Dear customer Tips on using the appliancePlease read these user instructions carefully Pass them on to any subsequent owner of the applianceContents What to do, if Installation and Connection InstructionsInstallation, Connection and Placing into Operation Safety InstructionsChild Safety General SafetyCorrect Use Economical and Ecological Dishwashing DisposalDisposing of the Packaging Material Disposal of Old AppliancesAppliance Features and Control Panel Multi-Display can display Control PanelPrior to using for the first time Special salt Adjusting the Water SoftenerYour area Electronic adjustment Fill with dishwasher salt Filling with Salt for the Water SoftenerUse dishwasher salt Open the door, remove the lower Rack Turning it anticlockwiseRinse Aid Switching Rinse Aid Supply On and OffThere are two ways to add rinse aid Fully open the rinse aid compartment lid Filling with Rinse AidDaily Use Adjusting Rinse Aid DosingNot be washed in the dishwasher Loading Cutlery and DishesTioned horizontally in the upper basket Loading CutleryPlace knives, small spoons and small Forks in the cutlery trayLoading Pans, Frying Pans Large Plates Fold the plate insert to the left Loading Cups, Glasses and Coffee ServicesLowering the Upper Basket Adjusting the Height of the Upper BasketRaising the Upper Basket Fill with detergent Filling with DetergentDetergent tablets Concentrated DetergentAutomatic Wash Programmes Soiling Selecting the Wash Programme Programme TableStart the Wash Programme Changing/Interrupting/CancellingWash Programme Changing the wash programmeCancelling the wash programme Setting or Changing the Delay Start TimerDishwasher is switched on again Changing the delay startLoad Sensing Sensor Logic Switching Off the DishwasherEmptying the Dishwasher Immediately after the end of the programmeCleaning the Filter Care and CleaningStances What to do, ifSymptom Possible Cause Solution Error messagesWash results are not satisfactory There are problems with the operation of the dish- washerDishes are still dirty Wrong wash programme was selectedDishes are wet and dull Technical DataRinse aid was not used Rinse aid container is empty Lower rinse aid dosingUpper basket without cutlery tray Sample loading arrangementsLower basket with cutlery basket See enclosed installation instructions Installing the DishwasherBuilt-Under Dishwasher Free-Standing AppliancesWork surface must be re-mounted Plinth on free-standing appliances is not adjustableWater Connection Connecting the DishwasherPermitted water pressure Connect the inlet hosePlease take care when installing the water inlet hose Water inlet hose with safety valveWater drain Appliance is automatically pumped out Leak Prevention SystemChanging a fuse Electrical ConnectionConnections Guarantee Conditions Customer Care 08705 929Calls may be recorded for training purposes AEG Hausgeräte GmbH Postfach 90327 Nürnberg Copyright by AEG