Electrolux 60820 Installing the Dishwasher, Built-Under Dishwasher, Free-Standing Appliances

Page 34

Installation and Connection Instructions

INSTALLATION AND CONNECTION INSTRUCTIONS

Installing the Dishwasher

•The dishwasher must be installed on a firm floor and adjusted such that it is stable and level.

• To compensate for unevenness in the floor and to match the height of the appliance to that of surrounding units extend the threaded feet by unscrew- ing:

– use a screwdriver.

• For built-in dishwashers the rear feet should be adjusted from the front of the appliance using a screwdriver.

• The drain hose, inlet hose and mains cable must be laid such that

	they are free to move in the rear of the plinth recess, so that they
	cannot be kinked or crushed.
	Built-Under Dishwasher
	(see enclosed installation instructions)
	Free-Standing Appliances
	can be set up as stand-alone without additional installation.
1	If the dishwasher is set up next to a gas or coal cooker, a heat-
	insulating, non-flammable plate must be mounted between the

dishwasher and the cooker, flush to the top edge of the work surface (depth 57.5 cm). The plate should have aluminium foil on the side fac- ing the cooker.

If the dishwasher is installed underneath a kitchen work surface, the original work surface of the dishwasher is to be removed as follows:

34

Image 34

Contents Favorit Please read these user instructions carefully Tips on using the applianceDear customer Pass them on to any subsequent owner of the applianceContents Installation and Connection Instructions What to do, ifChild Safety Safety InstructionsInstallation, Connection and Placing into Operation General SafetyCorrect Use Disposing of the Packaging Material DisposalEconomical and Ecological Dishwashing Disposal of Old AppliancesAppliance Features and Control Panel Control Panel Multi-Display can displayPrior to using for the first time Special salt Adjusting the Water SoftenerYour area Electronic adjustment Use dishwasher salt Open the door, remove the lower Rack Filling with Salt for the Water SoftenerFill with dishwasher salt Turning it anticlockwiseRinse Aid Switching Rinse Aid Supply On and OffThere are two ways to add rinse aid Filling with Rinse Aid Fully open the rinse aid compartment lidAdjusting Rinse Aid Dosing Daily UseLoading Cutlery and Dishes Not be washed in the dishwasherPlace knives, small spoons and small Loading CutleryTioned horizontally in the upper basket Forks in the cutlery trayLoading Pans, Frying Pans Large Plates Loading Cups, Glasses and Coffee Services Fold the plate insert to the leftLowering the Upper Basket Adjusting the Height of the Upper BasketRaising the Upper Basket Filling with Detergent Fill with detergentDetergent tablets Concentrated DetergentAutomatic Wash Programmes Selecting the Wash Programme Programme Table SoilingWash Programme Changing/Interrupting/CancellingStart the Wash Programme Changing the wash programmeDishwasher is switched on again Setting or Changing the Delay Start TimerCancelling the wash programme Changing the delay startEmptying the Dishwasher Switching Off the DishwasherLoad Sensing Sensor Logic Immediately after the end of the programmeCare and Cleaning Cleaning the FilterWhat to do, if StancesError messages Symptom Possible Cause SolutionDishes are still dirty There are problems with the operation of the dish- washerWash results are not satisfactory Wrong wash programme was selectedRinse aid was not used Rinse aid container is empty Technical DataDishes are wet and dull Lower rinse aid dosingUpper basket without cutlery tray Sample loading arrangementsLower basket with cutlery basket Built-Under Dishwasher Installing the DishwasherSee enclosed installation instructions Free-Standing AppliancesPlinth on free-standing appliances is not adjustable Work surface must be re-mountedPermitted water pressure Connecting the DishwasherWater Connection Connect the inlet hoseWater inlet hose with safety valve Please take care when installing the water inlet hoseWater drain Leak Prevention System Appliance is automatically pumped outElectrical Connection Changing a fuseConnections Guarantee Conditions Customer Care 08705 929Calls may be recorded for training purposes AEG Hausgeräte GmbH Postfach 90327 Nürnberg Copyright by AEG