Electrolux 60820 manual Setting or Changing the Delay Start Timer, Cancelling the wash programme

Page 26

Operating Instructions

0 1. Open the door of the dishwasher. The wash programme stops.

2.The indicator for the programme that is currently running extinguishes.

3.Close the door. The wash programme continues.

Cancelling the wash programme

0 1. Press the button for the current wash programme and hold it pressed. The programme indicator for the current wash programme flashes for a few seconds and then extinguishes.

2.Release the programme button, the wash programme is cancelled.

3	A selected programme is only interrupted by switching off the dish-
	washer, it is not cancelled. The wash programme is continued when the

dishwasher is switched on again.

Setting or Changing the Delay Start Timer

Using the delay start timer you can:

1.Press the ON/OFF button.

2.Press the DELAY TIMER button until the required delay (inhours) is flashing on the multi-display.

3.Press the button for the desired wash programme. The multi-display now displays the number of hours until the wash programme starts.

4.The wash programme starts automatically at the end of the time delay set.

Changing the delay start:

As long as the wash programme has not started, you can change the delay start set by pressing the DELAY TIMER button.

26

Image 26

Contents Favorit Please read these user instructions carefully Tips on using the applianceDear customer Pass them on to any subsequent owner of the applianceContents Installation and Connection Instructions What to do, ifChild Safety Safety InstructionsInstallation, Connection and Placing into Operation General SafetyCorrect Use Disposing of the Packaging Material DisposalEconomical and Ecological Dishwashing Disposal of Old AppliancesAppliance Features and Control Panel Control Panel Multi-Display can displayPrior to using for the first time Your area Adjusting the Water SoftenerSpecial salt Electronic adjustment Use dishwasher salt Open the door, remove the lower Rack Filling with Salt for the Water SoftenerFill with dishwasher salt Turning it anticlockwiseThere are two ways to add rinse aid Switching Rinse Aid Supply On and OffRinse Aid Filling with Rinse Aid Fully open the rinse aid compartment lidAdjusting Rinse Aid Dosing Daily UseLoading Cutlery and Dishes Not be washed in the dishwasherPlace knives, small spoons and small Loading CutleryTioned horizontally in the upper basket Forks in the cutlery trayLoading Pans, Frying Pans Large Plates Loading Cups, Glasses and Coffee Services Fold the plate insert to the leftRaising the Upper Basket Adjusting the Height of the Upper BasketLowering the Upper Basket Filling with Detergent Fill with detergentAutomatic Wash Programmes Concentrated DetergentDetergent tablets Selecting the Wash Programme Programme Table SoilingWash Programme Changing/Interrupting/CancellingStart the Wash Programme Changing the wash programmeDishwasher is switched on again Setting or Changing the Delay Start TimerCancelling the wash programme Changing the delay startEmptying the Dishwasher Switching Off the DishwasherLoad Sensing Sensor Logic Immediately after the end of the programmeCare and Cleaning Cleaning the FilterWhat to do, if StancesError messages Symptom Possible Cause SolutionDishes are still dirty There are problems with the operation of the dish- washerWash results are not satisfactory Wrong wash programme was selectedRinse aid was not used Rinse aid container is empty Technical DataDishes are wet and dull Lower rinse aid dosingLower basket with cutlery basket Sample loading arrangementsUpper basket without cutlery tray Built-Under Dishwasher Installing the DishwasherSee enclosed installation instructions Free-Standing AppliancesPlinth on free-standing appliances is not adjustable Work surface must be re-mountedPermitted water pressure Connecting the DishwasherWater Connection Connect the inlet hoseWater inlet hose with safety valve Please take care when installing the water inlet hoseWater drain Leak Prevention System Appliance is automatically pumped outElectrical Connection Changing a fuseConnections Guarantee Conditions Calls may be recorded for training purposes 08705 929Customer Care AEG Hausgeräte GmbH Postfach 90327 Nürnberg Copyright by AEG