Electrolux 60820 manual Error messages, Symptom Possible Cause Solution

Page 30

Operating Instructions

...Error messages

•If fault code (2 is displayed on the multi-display or the WATER indi- cator is illuminated, you can probably rectify the fault yourself. After rectifying a (2 fault and a fault related to the WATER indica- tor, press the button for the wash programme that has been started. The wash programme continues. If the fault code is displayed again, contact AEG Sevice Force.

•For all other faults, please contact AEG Sevice Force, stating the fault code.

Symptom

Possible Cause

Solution

The programme indica-

Tap is blocked or furred with

Clean tap.

tor for the selected

lime-scale.

 

programme is flashing

The filter (where present) in

 

and the WATER indica-

Clean the filter in the

tor is illuminated:

the threaded hose fitting is

threaded hose fitting.

blocked.

there is no water run-

 

 

 

ning into the dish-

The water inlet hose is not

Check hose installation.

washer.

correctly laid.

 

Fault code (2 is dis-

The sink outlet is blocked.

Clean the sink outlet.

played on the multi-

 

 

display.

 

 

The programme indica-

The water drain hose is not

Check hose installation.

tor for the selected

correctly laid.

wash programme is

 

 

 

flashing.

 

 

Fault code (3 is dis-

The leak prevention system

Close the tap and contact

played on the multi-

your local AEG Sevice Force

has been triggered.

display.

Centre.

 

 

 

 

 

The FILTER indicator is only

 

 

intended to remind you to

 

 

check the filter in the dish-

 

The FILTER indicator is

washer from time to time

The indicator goes out auto-

illuminated.

and, if necessary, to clean it.

matically on the start of the

It illuminates at regular

next wash programme.

 

 

intervals, independent of the

 

 

amount of soiling of the fil-

 

 

ter.

 

 

 

 

30

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Favorit Please read these user instructions carefully Tips on using the applianceDear customer Pass them on to any subsequent owner of the applianceContents Installation and Connection Instructions What to do, ifChild Safety Safety InstructionsInstallation, Connection and Placing into Operation General SafetyCorrect Use Disposing of the Packaging Material DisposalEconomical and Ecological Dishwashing Disposal of Old AppliancesAppliance Features and Control Panel Control Panel Multi-Display can displayPrior to using for the first time Adjusting the Water Softener Special saltYour area Electronic adjustment Use dishwasher salt Open the door, remove the lower Rack Filling with Salt for the Water SoftenerFill with dishwasher salt Turning it anticlockwiseSwitching Rinse Aid Supply On and Off Rinse AidThere are two ways to add rinse aid Filling with Rinse Aid Fully open the rinse aid compartment lidAdjusting Rinse Aid Dosing Daily UseLoading Cutlery and Dishes Not be washed in the dishwasherPlace knives, small spoons and small Loading CutleryTioned horizontally in the upper basket Forks in the cutlery trayLoading Pans, Frying Pans Large Plates Loading Cups, Glasses and Coffee Services Fold the plate insert to the leftAdjusting the Height of the Upper Basket Lowering the Upper BasketRaising the Upper Basket Filling with Detergent Fill with detergentConcentrated Detergent Detergent tabletsAutomatic Wash Programmes Selecting the Wash Programme Programme Table SoilingWash Programme Changing/Interrupting/CancellingStart the Wash Programme Changing the wash programmeDishwasher is switched on again Setting or Changing the Delay Start TimerCancelling the wash programme Changing the delay startEmptying the Dishwasher Switching Off the DishwasherLoad Sensing Sensor Logic Immediately after the end of the programmeCare and Cleaning Cleaning the FilterWhat to do, if StancesError messages Symptom Possible Cause SolutionDishes are still dirty There are problems with the operation of the dish- washerWash results are not satisfactory Wrong wash programme was selectedRinse aid was not used Rinse aid container is empty Technical DataDishes are wet and dull Lower rinse aid dosingSample loading arrangements Upper basket without cutlery trayLower basket with cutlery basket Built-Under Dishwasher Installing the DishwasherSee enclosed installation instructions Free-Standing AppliancesPlinth on free-standing appliances is not adjustable Work surface must be re-mountedPermitted water pressure Connecting the DishwasherWater Connection Connect the inlet hoseWater inlet hose with safety valve Please take care when installing the water inlet hoseWater drain Leak Prevention System Appliance is automatically pumped outElectrical Connection Changing a fuseConnections Guarantee Conditions 08705 929 Customer CareCalls may be recorded for training purposes AEG Hausgeräte GmbH Postfach 90327 Nürnberg Copyright by AEG
Top Page Image Contents