KitchenAid UXI0600DYS Rear Mounting-Blower Motor, Bottom Venting, Left or Right Venting

Page 12

Bottom Venting:

NOTE: If installing the vent damper in the down position, a wall or roof cap with a damper at the exit end of the vent system is required.

■Downdraft vent is shipped with blower in down venting position so no modification is required.

■If rear mounting of the blower motor is not required, go to the “Complete Installation (Interior-Mounted Motor)” section.

■To mount the blower motor to the rear side of the vent box, go to the “Rear Mounting - Blower Motor” section.

Left or Right Venting:

1.Using two or more people, place the downdraft vent system on its back.

2.Remove the 4 screws from the cover plate mounted to the face of the motor box and set them aside.

Rear Mounting—Blower Motor

NOTE: Optional blower motor rear mounting position (opposite side) for island cabinet locations. The blower motor box assembly can be moved to the opposite side (rear) of the vent box.

1.Remove 7 screws from the mounting flanges of the blower motor box.

Front View

A

A

A

A

B

C

D

A.Cover plate

B.Cover plate screws (4)

C.Cover plate keyhole slot shoulder screws (4)

G

F

E

D. Motor mounting screws (4) E. Vent cover plate

F. Motor box

G. Vent cover screws (3)

C

B

A. Screws (7)

B. Keyhole slot shoulder screws (2)

C. Blower motor box

2.Lift blower motor box off the shoulder screws in the keyhole slots. Disconnect wire connection from blower motor and set blower motor box aside.

3.Remove 6 screws from the mounting flange of the ¹⁄₄" (6.4 mm) deep cover.

Rear View

3.Slide the cover plate up and slip it over the keyhole slot shoulder screws. Set the cover aside.

4.Remove 4 screws from the bottom of the motor box that hold the motor assembly to the motor box.

NOTE: Disconnect the electrical wiring connection from motor if needed.

5.Remove 3 screws and the vent cover plate from the left or right side of the motor box for the venting direction to be used.

6.Rotate the blower motor assembly 90 degrees to the left or right side to the chosen venting direction and secure to the blower box with motor mounting screws previously removed. Do not twist or bind the wires.

7.Install the vent cover plate over the rectangular opening in the bottom of the motor box and secure with vent cover screws.

NOTE: Reinstall the electrical wiring connection to motor if removed.

8.Reinstall the cover plate to the face of the motor box and secure with 4 cover plate screws previously removed.

9.For mounting the blower motor to the back of the vent box, go to the “Rear Mounting - Blower Motor” section. Otherwise, go to the “Complete Installation (Interior-Mounted Motor)” section.

C

A

 

B

A. Screws (6)

B. Keyhole slot shoulder screws (2)

C. ¹⁄₄" (6.4 mm) deep cover

4.Lift the ¹⁄₄" (6.4 mm) deep cover off the shoulder screws in the keyhole slots and set the cover aside.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Table of Contents/Table des matières Retractable POP-UP Downdraft Vent SystemTable of Contents Table DES MatièresVent System Safety Your safety and the safety of others are very importantImportant Safety Instructions Installation Requirements Tools and PartsLocation Requirements Product Dimensions Models with interior-mounted blower motorCabinet Dimensions Countertop Cutout DimensionsElectrical Requirements Venting RequirementsInstallation Instructions INTERIOR-MOUNTED Vent Motor Venting MethodsIsland Location Built-In Cabinet LocationsCalculating Vent System Length Example Vent SystemInstall Vent System Determine Which Vent Direction Is Best for Your InstallationRear Mounting-Blower Motor Bottom VentingLeft or Right Venting Front ViewComplete Installation Remove the screws from the wire mounting plate¹⁄₄ x 10 8.3 x 25.4 cm Back Draft Damper Cm Round Vent Transition with DamperRemove 4 screws attaching the terminal box cover Tighten the lower support legs screwsMake Electrical Connections Check OperationInstallation Instructions EXTERIOR-MOUNTED Vent Motor Maximum Length of Vent SystemFront or Rear Venting Complete Installation Exterior-Mounted Motor Install Downdraft Vent In-Line External Type Blower MotorPrepare for Mounting the In-Line Blower System Install In-line Blower System Outlet Side Drill 4 mounting pilot holes using a ³⁄₁₆ 4.8 mm drill bitPrepare the In-line Blower System Inlet SideMake Electrical Connections for In-Line Blower Motor System Electrical Connection Inside In-line Blower SystemMake Electrical Power Supply Connection to Downdraft Vent Disconnect power Locate the downdraft vent terminal boxCheck Operation When Cooking Is Complete Vent System USEOperating Downdraft Vent To UseVent System Care Surface of Downdraft VentFilters Wiring Diagrams Interior-Mounted Blower MotorSEL0016521 Exterior-Mounted Blower MotorAssistance or Service AccessoriesU.S.A CanadaKitchenaid Ventilation Warranty This limited warranty does not coverSécurité DU Système DE Ventilation Votre sécurité et celle des autres est très importanteImportantes Instructions DE Sécurité Exigences Dinstallation Exigences demplacementOutils et pièces Dimensions du produit Modèles à ventilateur monté à lintérieurDimensions du placard RemarquesPlan de travail Dimensions des ouvertures à découper Tableau des dimensions de l’ouverture du plan de travailLongueur recommandée pour le système d’extraction Installations dans les régions au climat froidSpécifications électriques Exigences concernant l’évacuationInstructions D’INSTALLATION Ventilateur Monté À L’INTÉRIEUR Configuration en îlotMéthodes d’évacuation Calcul de la longueur effective du circuit d’évacuationInstallation du conduit d’évacuation Exemple de circuit d’évacuationRectangulaire de 3¹⁄₄ x Composant Cm x 25,4 cmÉvacuation par le bas Montage du ventilateur à l’arrière Sortie par le côté gauche ou le côté droitVue de face Vue arrièreAchever l’installation Clapet anti-retour de 3¹⁄₄ x 10 8,3 x 25,4 cmRaccord de transition rond de 6 15,2 cm avec clapet Retirer les vis de la platine de montage du câbleRaccordements électriques Ôter les 4 vis du couvercle du boîtier de connexionSerrer les vis des pieds de soutien Déconnecter la source de courant électriqueAvertissement Contrôle du fonctionnementInstructions D’INSTALLATION Ventilateur Monté À L’EXTÉRIEUR Configuration avec encastrementConfiguration en îlot- Évacuation par l’avant Configuration en îlot- Évacuation par l’arrièreÉvacuation par l’avant ou par l’arrière Achever l’installation Ventilateur monté à l’extérieur Préparation du montage du système de ventilation en ligneInstallation du système de ventilation en ligne Préparation du système de ventilation en ligneCôté sortie Côté entréeInstaller les connecteurs de conduit et le conduit dans les De conduit de ¹⁄₂ 1,3 cm homologués UL ou CSAConduit de câblage de ¹⁄₂ 1,3 cm entre le logement du Suffisamment de conduit de câblage de ¹⁄₂ 1,3 cm pourConduit de câblage ¹⁄₂ 1,3 cm Homologation UL Par le bas Utilisation DU Système D’EXTRACTION Utilisation du système d’extraction par le basUtilisation Lorsque la cuisson est terminéeEntretien DU Système D’ÉVACUATION Surface du système d’extraction par le basSchéma DE Câblage Ventilateur monté à lintérieurSEL0016521 Ventilateur monté à lextérieurAssistance OU Service AccessoiresAux États-Unis Au CanadaGarantie DU Système DE Ventilation Kitchenaid La présente garantie limitée ne couvre pasComposer le 1-800-422-1230. Au Canada, composer le W10342489E

UXI01200DYS, UXI0600DYS specifications

The KitchenAid UXI0600DYS and UXI01200DYS are two innovative under-cabinet range hoods designed to enhance kitchen functionality while adding a touch of elegance. These range hoods provide homeowners with the ideal balance of performance and style, making them popular choices for modern kitchens.

The UXI0600DYS, with its sleek design and powerful performance, is a 36-inch hood that offers a maximum airflow of 600 CFM to efficiently eliminate smoke, odors, and moisture from the cooking area. Its three-speed fan allows users to select the appropriate level of ventilation based on cooking needs, ensuring a comfortable environment. The convenience of a dishwasher-safe filter simplifies maintenance, allowing for easy cleaning and longevity of the unit.

On the other hand, the UXI01200DYS is designed for smaller spaces, offering a compact 30-inch option that does not compromise on performance. With a maximum airflow of 300 CFM and a two-speed fan, it provides adequate ventilation for everyday cooking tasks. Its stainless steel finish complements a variety of kitchen styles, providing a seamless addition to any decor.

Both models incorporate advanced noise-reduction technology, ensuring that the operation of the fan remains quiet, allowing for conversation and enjoyment during cooking. The easy-to-use control panel features sleek push button controls, making it simple to operate even while preparing meals.

Each range hood is equipped with LED lighting, enhancing visibility over the cooking surface. This not only provides a practical solution but also contributes to the overall ambiance of the kitchen. The illumination helps home chefs keep an eye on their dishes while adding a modern touch to the space.

Installation versatility is another noteworthy characteristic, as both range hoods can be mounted under cabinets, optimizing kitchen space without compromising functionality. The UXI0600DYS and UXI01200DYS are ideal for homeowners seeking effective ventilation solutions that blend performance with an attractive design.

In summary, the KitchenAid UXI0600DYS and UXI01200DYS range hoods are excellent choices for any kitchen, providing powerful ventilation, quiet operation, easy maintenance, and stylish design, thus fulfilling the diverse needs of home chefs.
Top Page Image Contents