KitchenAid UXI01200DYS Complete Installation, ¹⁄₄ x 10 8.3 x 25.4 cm Back Draft Damper

Page 13

5.Remove the screws from the wire mounting plate.

A A

BC

A.Screws

B.Wire mounting plate

C.Blower motor box

6.Hold the wire mounting plate and push the grommet out of the mounting plate.

A

B

A. Wire mounting plate

B.Grommet

7.Slide the wire assembly through the slot in the wire mounting plate to remove it.

8.Place the wire assembly through the opening to the opposite side of the vent box.

9.Reassemble the wire assembly and grommet to the wire mounting plate

10.Install the wire mounting plate to the vent box using the 4 screws previously removed.

11.Place the blower motor box assembly with the keyhole slots over the 2 shoulder screws on the rear of the vent box and reconnect the wire connection to the blower motor.

12.Mount the blower motor box to the vent box and secure using the 6 screws previously removed.

13.Mount the 4³⁄₄" (12.0 cm) cover box (supplied) to the front of the vent box. Place the keyhole slots over the 2 shoulder screws, align the mounting holes, and secure the cover box to vent box using the 6 screws previously removed from the ¹⁄₄" (6.4 mm) deep cover.

14.Go to the “Complete Installation (Interior-Mounted Motor)” section.

Complete Installation

(Interior-Mounted Motor)

NOTE: The downdraft vent system is supplied with a 3¹⁄₄" x 10" (8.3 x 25.4 cm) back draft damper and a 6" (15.2 cm) round vent transition with damper. Refer to “3¹⁄₄" x 10" (8.3 x 25.4 cm) back draft damper” or “6" (15.2 cm) round vent transition with damper,” depending upon the type of venting you are using.

3¹⁄₄" x 10" (8.3 x 25.4 cm) Back Draft Damper

1.Attach the 3¼" x 10" (8.3 x 25.4 cm) back draft damper to the vent opening in the blower motor box, using three 3.5 x

9.5 mm screws.

B A

A

A. 3.5 x 9.5 mm screws

B. 3¼" x 10" (8.3 x 25.4 cm) back draft damper

6" (15.2 cm) Round Vent Transition with Damper

1.Attach the 6" (15.2 cm) round vent transition to vent opening (left or right side venting only is recommended), using two 3.5 x 9.5 mm screws.

A

B

A. 3.5 x 9.5 mm screws

B. 6" (15.2 cm) round vent transition with damper

13

Image 13
Contents Retractable POP-UP Downdraft Vent System Table of Contents/Table des matièresTable DES Matières Table of ContentsYour safety and the safety of others are very important Vent System SafetyImportant Safety Instructions Tools and Parts Installation RequirementsLocation Requirements Models with interior-mounted blower motor Product DimensionsCountertop Cutout Dimensions Cabinet DimensionsVenting Requirements Electrical RequirementsVenting Methods Installation Instructions INTERIOR-MOUNTED Vent MotorIsland Location Built-In Cabinet LocationsExample Vent System Calculating Vent System LengthDetermine Which Vent Direction Is Best for Your Installation Install Vent SystemBottom Venting Rear Mounting-Blower MotorLeft or Right Venting Front ViewRemove the screws from the wire mounting plate Complete Installation¹⁄₄ x 10 8.3 x 25.4 cm Back Draft Damper Cm Round Vent Transition with DamperTighten the lower support legs screws Remove 4 screws attaching the terminal box coverCheck Operation Make Electrical ConnectionsMaximum Length of Vent System Installation Instructions EXTERIOR-MOUNTED Vent MotorFront or Rear Venting Install Downdraft Vent In-Line External Type Blower Motor Complete Installation Exterior-Mounted MotorPrepare for Mounting the In-Line Blower System Drill 4 mounting pilot holes using a ³⁄₁₆ 4.8 mm drill bit Install In-line Blower System Outlet SidePrepare the In-line Blower System Inlet SideElectrical Connection Inside In-line Blower System Make Electrical Connections for In-Line Blower Motor SystemDisconnect power Locate the downdraft vent terminal box Make Electrical Power Supply Connection to Downdraft VentCheck Operation Vent System USE When Cooking Is CompleteOperating Downdraft Vent To UseSurface of Downdraft Vent Vent System CareFilters Interior-Mounted Blower Motor Wiring DiagramsExterior-Mounted Blower Motor SEL0016521Accessories Assistance or ServiceU.S.A CanadaThis limited warranty does not cover Kitchenaid Ventilation WarrantyVotre sécurité et celle des autres est très importante Sécurité DU Système DE VentilationImportantes Instructions DE Sécurité Exigences demplacement Exigences DinstallationOutils et pièces Modèles à ventilateur monté à lintérieur Dimensions du produitRemarques Dimensions du placardTableau des dimensions de l’ouverture du plan de travail Plan de travail Dimensions des ouvertures à découperInstallations dans les régions au climat froid Longueur recommandée pour le système d’extractionSpécifications électriques Exigences concernant l’évacuationConfiguration en îlot Instructions D’INSTALLATION Ventilateur Monté À L’INTÉRIEURMéthodes d’évacuation Calcul de la longueur effective du circuit d’évacuationExemple de circuit d’évacuation Installation du conduit d’évacuationRectangulaire de 3¹⁄₄ x Composant Cm x 25,4 cmÉvacuation par le bas Sortie par le côté gauche ou le côté droit Montage du ventilateur à l’arrièreVue de face Vue arrièreClapet anti-retour de 3¹⁄₄ x 10 8,3 x 25,4 cm Achever l’installationRaccord de transition rond de 6 15,2 cm avec clapet Retirer les vis de la platine de montage du câbleÔter les 4 vis du couvercle du boîtier de connexion Raccordements électriquesSerrer les vis des pieds de soutien Déconnecter la source de courant électriqueContrôle du fonctionnement AvertissementConfiguration avec encastrement Instructions D’INSTALLATION Ventilateur Monté À L’EXTÉRIEURConfiguration en îlot- Évacuation par l’avant Configuration en îlot- Évacuation par l’arrièreÉvacuation par l’avant ou par l’arrière Préparation du montage du système de ventilation en ligne Achever l’installation Ventilateur monté à l’extérieurPréparation du système de ventilation en ligne Installation du système de ventilation en ligneCôté sortie Côté entréeDe conduit de ¹⁄₂ 1,3 cm homologués UL ou CSA Installer les connecteurs de conduit et le conduit dans lesConduit de câblage de ¹⁄₂ 1,3 cm entre le logement du Suffisamment de conduit de câblage de ¹⁄₂ 1,3 cm pourConduit de câblage ¹⁄₂ 1,3 cm Homologation UL Par le bas Utilisation du système d’extraction par le bas Utilisation DU Système D’EXTRACTIONUtilisation Lorsque la cuisson est terminéeSurface du système d’extraction par le bas Entretien DU Système D’ÉVACUATIONVentilateur monté à lintérieur Schéma DE CâblageVentilateur monté à lextérieur SEL0016521Accessoires Assistance OU ServiceAux États-Unis Au CanadaLa présente garantie limitée ne couvre pas Garantie DU Système DE Ventilation KitchenaidComposer le 1-800-422-1230. Au Canada, composer le W10342489E

UXI01200DYS, UXI0600DYS specifications

The KitchenAid UXI0600DYS and UXI01200DYS are two innovative under-cabinet range hoods designed to enhance kitchen functionality while adding a touch of elegance. These range hoods provide homeowners with the ideal balance of performance and style, making them popular choices for modern kitchens.

The UXI0600DYS, with its sleek design and powerful performance, is a 36-inch hood that offers a maximum airflow of 600 CFM to efficiently eliminate smoke, odors, and moisture from the cooking area. Its three-speed fan allows users to select the appropriate level of ventilation based on cooking needs, ensuring a comfortable environment. The convenience of a dishwasher-safe filter simplifies maintenance, allowing for easy cleaning and longevity of the unit.

On the other hand, the UXI01200DYS is designed for smaller spaces, offering a compact 30-inch option that does not compromise on performance. With a maximum airflow of 300 CFM and a two-speed fan, it provides adequate ventilation for everyday cooking tasks. Its stainless steel finish complements a variety of kitchen styles, providing a seamless addition to any decor.

Both models incorporate advanced noise-reduction technology, ensuring that the operation of the fan remains quiet, allowing for conversation and enjoyment during cooking. The easy-to-use control panel features sleek push button controls, making it simple to operate even while preparing meals.

Each range hood is equipped with LED lighting, enhancing visibility over the cooking surface. This not only provides a practical solution but also contributes to the overall ambiance of the kitchen. The illumination helps home chefs keep an eye on their dishes while adding a modern touch to the space.

Installation versatility is another noteworthy characteristic, as both range hoods can be mounted under cabinets, optimizing kitchen space without compromising functionality. The UXI0600DYS and UXI01200DYS are ideal for homeowners seeking effective ventilation solutions that blend performance with an attractive design.

In summary, the KitchenAid UXI0600DYS and UXI01200DYS range hoods are excellent choices for any kitchen, providing powerful ventilation, quiet operation, easy maintenance, and stylish design, thus fulfilling the diverse needs of home chefs.