KitchenAid UXI01200DYS, UXI0600DYS Install Vent System, Front or Rear Venting

Page 17

Install Vent System

WARNING

Excessive Weight Hazard

Use two or more people to move and install downdraft vent.

Failure to do so can result in back or other injury.

1.Place cardboard or similar material on top of a flat surface where you can easily assemble the downdraft vent system.

2.Remove parts packages, downdraft vent and blower box from the carton.

3.Remove all shipping materials, tape and film from the downdraft vent and blower box.

4.Install the right and left undercounter mounting brackets to the vent box. Slide the keyhole slots over the guide tabs and push the brackets up to set them in place.

B

A

C

D

A. Vent box

B. Undercounter mounting bracket

C. Keyhole slots

D. Guide tabs

5.Attach the left and right side end caps to the downdraft vent. Place the end cap upon the overcounter support, slide the tab into the slot and snap into place over the plastic tabs.

A

B

A. End cap tab

B. Mounting slot

6.Measure distance “X” from the cabinet floor to the top of the countertop. Subtract 28¹⁄₂" from distance “X” to determine dimension “Y” (X - 28¹⁄₂" = Y).

Top of countertop

Downdraft vent

28¹⁄₂"

(73 cm)

“X“

“Y“

Cabinet floor

7.Attach the support legs to the side of the vent box with

4 - 4 x 8 mm screws in each support leg. Adjust to dimension “Y” from the bottom of the vent box to the bottom of the support legs. Tighten screws.

C

A

Dim. “Y”

B

A. Motor box

B. Support leg

C. 4 x 8 mm screws (4)

Determine Which Vent Direction Is Best for Your Installation

When installed in a cabinet the vent system can exhaust through the front or rear of the vent box. The downdraft vent is shipped with a 10" diameter vent collar plate.

Front or Rear Venting:

1.Using two or more people, place the downdraft vent system on the opposite side for venting.

2.Remove the 4 screws from the cover plate mounted to the face of the motor box and set them aside.

3.Slide the cover plate up and slip it over the keyhold slot shoulder screws. Set the cover aside.

4.Install the 10" diameter vent collar plate to the vent box where the cover plate was removed in the previous step. Secure using the 4 screws from the cover plate.

5.Go to the “Complete Installation (Exterior-Mounted Motor)” section.

17

Image 17
Contents Retractable POP-UP Downdraft Vent System Table of Contents/Table des matièresTable DES Matières Table of ContentsYour safety and the safety of others are very important Vent System SafetyImportant Safety Instructions Location Requirements Installation RequirementsTools and Parts Models with interior-mounted blower motor Product DimensionsCountertop Cutout Dimensions Cabinet DimensionsVenting Requirements Electrical RequirementsVenting Methods Installation Instructions INTERIOR-MOUNTED Vent MotorIsland Location Built-In Cabinet LocationsExample Vent System Calculating Vent System LengthDetermine Which Vent Direction Is Best for Your Installation Install Vent SystemBottom Venting Rear Mounting-Blower MotorLeft or Right Venting Front ViewRemove the screws from the wire mounting plate Complete Installation¹⁄₄ x 10 8.3 x 25.4 cm Back Draft Damper Cm Round Vent Transition with DamperTighten the lower support legs screws Remove 4 screws attaching the terminal box coverCheck Operation Make Electrical ConnectionsMaximum Length of Vent System Installation Instructions EXTERIOR-MOUNTED Vent MotorFront or Rear Venting Prepare for Mounting the In-Line Blower System Complete Installation Exterior-Mounted MotorInstall Downdraft Vent In-Line External Type Blower Motor Drill 4 mounting pilot holes using a ³⁄₁₆ 4.8 mm drill bit Install In-line Blower System Outlet SidePrepare the In-line Blower System Inlet SideElectrical Connection Inside In-line Blower System Make Electrical Connections for In-Line Blower Motor SystemDisconnect power Locate the downdraft vent terminal box Make Electrical Power Supply Connection to Downdraft VentCheck Operation Vent System USE When Cooking Is CompleteOperating Downdraft Vent To UseFilters Vent System CareSurface of Downdraft Vent Interior-Mounted Blower Motor Wiring DiagramsExterior-Mounted Blower Motor SEL0016521Accessories Assistance or ServiceU.S.A CanadaThis limited warranty does not cover Kitchenaid Ventilation WarrantyVotre sécurité et celle des autres est très importante Sécurité DU Système DE VentilationImportantes Instructions DE Sécurité Outils et pièces Exigences DinstallationExigences demplacement Modèles à ventilateur monté à lintérieur Dimensions du produitRemarques Dimensions du placardTableau des dimensions de l’ouverture du plan de travail Plan de travail Dimensions des ouvertures à découperInstallations dans les régions au climat froid Longueur recommandée pour le système d’extractionSpécifications électriques Exigences concernant l’évacuationConfiguration en îlot Instructions D’INSTALLATION Ventilateur Monté À L’INTÉRIEURMéthodes d’évacuation Calcul de la longueur effective du circuit d’évacuationExemple de circuit d’évacuation Installation du conduit d’évacuationRectangulaire de 3¹⁄₄ x Composant Cm x 25,4 cmÉvacuation par le bas Sortie par le côté gauche ou le côté droit Montage du ventilateur à l’arrièreVue de face Vue arrièreClapet anti-retour de 3¹⁄₄ x 10 8,3 x 25,4 cm Achever l’installationRaccord de transition rond de 6 15,2 cm avec clapet Retirer les vis de la platine de montage du câbleÔter les 4 vis du couvercle du boîtier de connexion Raccordements électriquesSerrer les vis des pieds de soutien Déconnecter la source de courant électriqueContrôle du fonctionnement AvertissementConfiguration avec encastrement Instructions D’INSTALLATION Ventilateur Monté À L’EXTÉRIEURConfiguration en îlot- Évacuation par l’avant Configuration en îlot- Évacuation par l’arrièreÉvacuation par l’avant ou par l’arrière Préparation du montage du système de ventilation en ligne Achever l’installation Ventilateur monté à l’extérieurPréparation du système de ventilation en ligne Installation du système de ventilation en ligneCôté sortie Côté entréeDe conduit de ¹⁄₂ 1,3 cm homologués UL ou CSA Installer les connecteurs de conduit et le conduit dans lesConduit de câblage de ¹⁄₂ 1,3 cm entre le logement du Suffisamment de conduit de câblage de ¹⁄₂ 1,3 cm pourConduit de câblage ¹⁄₂ 1,3 cm Homologation UL Par le bas Utilisation du système d’extraction par le bas Utilisation DU Système D’EXTRACTIONUtilisation Lorsque la cuisson est terminéeSurface du système d’extraction par le bas Entretien DU Système D’ÉVACUATIONVentilateur monté à lintérieur Schéma DE CâblageVentilateur monté à lextérieur SEL0016521Accessoires Assistance OU ServiceAux États-Unis Au CanadaComposer le 1-800-422-1230. Au Canada, composer le Garantie DU Système DE Ventilation KitchenaidLa présente garantie limitée ne couvre pas W10342489E

UXI01200DYS, UXI0600DYS specifications

The KitchenAid UXI0600DYS and UXI01200DYS are two innovative under-cabinet range hoods designed to enhance kitchen functionality while adding a touch of elegance. These range hoods provide homeowners with the ideal balance of performance and style, making them popular choices for modern kitchens.

The UXI0600DYS, with its sleek design and powerful performance, is a 36-inch hood that offers a maximum airflow of 600 CFM to efficiently eliminate smoke, odors, and moisture from the cooking area. Its three-speed fan allows users to select the appropriate level of ventilation based on cooking needs, ensuring a comfortable environment. The convenience of a dishwasher-safe filter simplifies maintenance, allowing for easy cleaning and longevity of the unit.

On the other hand, the UXI01200DYS is designed for smaller spaces, offering a compact 30-inch option that does not compromise on performance. With a maximum airflow of 300 CFM and a two-speed fan, it provides adequate ventilation for everyday cooking tasks. Its stainless steel finish complements a variety of kitchen styles, providing a seamless addition to any decor.

Both models incorporate advanced noise-reduction technology, ensuring that the operation of the fan remains quiet, allowing for conversation and enjoyment during cooking. The easy-to-use control panel features sleek push button controls, making it simple to operate even while preparing meals.

Each range hood is equipped with LED lighting, enhancing visibility over the cooking surface. This not only provides a practical solution but also contributes to the overall ambiance of the kitchen. The illumination helps home chefs keep an eye on their dishes while adding a modern touch to the space.

Installation versatility is another noteworthy characteristic, as both range hoods can be mounted under cabinets, optimizing kitchen space without compromising functionality. The UXI0600DYS and UXI01200DYS are ideal for homeowners seeking effective ventilation solutions that blend performance with an attractive design.

In summary, the KitchenAid UXI0600DYS and UXI01200DYS range hoods are excellent choices for any kitchen, providing powerful ventilation, quiet operation, easy maintenance, and stylish design, thus fulfilling the diverse needs of home chefs.