Frymaster H17SC, H22SC Electronics and Wiring Components 8.4.1.1 Single Component Box, Part #

Page 57

8.4Electronics and Wiring Components

8.4Electronics and Wiring Components

8.4.1.1Single Component Box

	ITEM	STANDARD	EURO-LOOK	COMPONENT
		PART #	PART #

	106-0580		Component Box Assembly Single Navy
1	106-0313		Wire Assembly, Component SFP120
2	806-7179SP		Sound Device
3	806-7935		PCB Assembly, Interface
4	806-9559		Component Box W/ Studs
5	807-0012		Relay, 18AMP 1/3 HP 24V Coil
6	807-0065		Block, Terminal
7	807-0069		Circuit Breaker, 10A
8	807-0070		Terminal, Ground Lug
9	807-0855		Transformer, 120V 50/60 – 12V 20A
10	807-1612		Clamp, 3/8 Connector Type (Thin Screw)
11	807-2181		Transformer, Power 100-120V/24V 62VA
12	809-0102		Screw, 8 – 32 x 3/8 TR SL HD ZP
13	809-0104		Screw, 8 – 32 x ½ TR SL HD ZP
14	809-0247		Nut, 8 – 32 Hex KEPS ZP
15	809-0250		Nut, 6 – 32 Hex KEPS ZP
16	809-0349		Spacer, 4mm x 6mm Aluminum
17	809-0360		Screw, 8 x 3/8 Type 8 Hex Washer SL HD ZP
18	826-1374		Screw, #10 – ½ Hex Head (Pkg. of 25)
19	810-0045		Bushing, .875 Dia Hole 11/16
20	810-1164		Block, 1 Plc Screwless Terminal
21	812-0368		Conduit, Flex 3/8”
22	816-0217		Paper, Insulating Terminal Block CE
23	WIR-0428		Wire Assembly, Navy SFP Component
24	WIR-0581		Wire Assembly, Transformer 440V
					Use standard part.
		8-12

Image 57

Contents andPartsManualService,Operation,Installation 24-Hour Service HotlineFRYERS 8196004DANGER NOTICE TO U.S. CUSTOMERS Never spray the fryer with water or use water jets to clean the fryerNOTICE TO OWNERS OF UNITS EQUIPPED WITH COMPUTERS U.S CANADANavy Surface Ship Electric Fryers Installation, Operation, Service, and Parts Manual TABLE OF CONTENTS1.2 Safety Information NAVY SURFACE SHIP ELECTRIC FRYERS CHAPTER 1 INTRODUCTION1.1 General 1.5 Service Information 1.4 Shipping Damage Claim Procedure1.3 Controller Information RETAIN AND STORE THIS MANUAL IN A SAFE PLACE FOR FUTURE USENAVY SURFACE SHIP ELECTRIC FRYERS CHAPTER 2 INSTALLATION INSTRUCTIONS 2.1 IntroductionDo not block the area around the base or under the fryers Do not connect the contacts in series 2.2 Power RequirementsDo not connect more than one fryer to each set of contacts The contacts CANNOT have an external voltage applied2.3 Installation 2.5 Dimensions and Weights2.4 After Fryers Are Anchored At the Frying Station DANGER Single Fryer 2-Fryer BatteryFRONT HANDLE BACK OF FRYER UNIT4-Fryer Battery 3-Fryer Battery2.470 62.55NAVY SURFACE SHIP ELECTRIC FRYERS CHAPTER 3 OPERATING INSTRUCTIONS 3.1 Equipment Setup and Shutdown Procedures3.2 Operation of the Solid-State Analog Controller ShutdownDESCRIPTION properly filled with oil. See Section CONTROLLER OPERATING PROCEDURE HIGH-LIMIT TEST PROCEDUREThe analog controller has no timing features. The operator must monitor shake and pull times 5. Place the controller power switch in the OFF position NAVY SURFACE SHIP ELECTRIC FRYERS CHAPTER 4 FILTRATION INSTRUCTIONS 4.1 Introduction4.2 Preparing the Filter for Use 3. Place the metal filter screen in the center of the bottom of the pan, then lay a sheet of filter paper on top of the screen, over- lapping on all sides 4.3 Operation of the Filter DANGER2. Remove the basket support rack from the frypot, raise the element assembly to the up position, and snap the Power Shower into position 6. Lower the elements into the frypot and reinstall the basket support rack. Ensure the drain valve is fully closed. If the drain valve is not fully closed, the fryer will not operate. Turn the fryer ON and allow the cooking oil to reach setpoint 4.4 Draining and Disposing of Waste Oil5.1 Cleaning the Fryer DANGER NAVY SURFACE SHIP ELECTRIC FRYERS CHAPTER 5 PREVENTIVE MAINTENANCE5.1.1 Clean Inside and Outside of the Fryer Cabinet - Daily 5.1.2 Clean the Built-in Filtration System - Daily5.1.3 Clean the Frypot and Heating Elements - Weekly DANGER Boiling-Out the Frypot2. Press the fryer ON/OFF switch to the ON position 5.1.4 Clean Detachable Parts and Accessories - Weekly 5.2 Check Calibration of Temperature Control Knob - Monthly5. Turn the fryer ON/OFF switchs to the OFF position 5.3 Annual/Periodic System Inspection FryerBuilt-In Filtration System Check filtration system integrity as follows − Verify that filter pan cover is present and properly installed6.1 Introduction NAVY SURFACE SHIP ELECTRIC FRYERS CHAPTER 6 OPERATOR TROUBLESHOOTINGVerify that power is connected and that circuit breakers are on Verify that frypot drain valves are fully closed6.2 Troubleshooting 6.2.1 Control and Heating Problems ProblemProbable Causes Corrective ActionProbable Causes 6.2.3 Filtration Problems 6.2.2 Error Messages and Display ProblemsFilter pump runs 6.3 Replacing the Controller or Controller Wiring Harness NAVY SURFACE SHIP ELECTRIC FRYERS CHAPTER 7 SERVICE PROCEDURES 7.1 General7.2 Replacing a Controller 7.3 Replacing Component Box Components 7.4 Replacing a Temperature Probe or High-Limit Thermostat DO NOT drain more than one full frypot into the SDU at one time1. Remove the filter pan and lid from the unit. Drain the frypots into a Shortening Disposal Unit SDU or other appropriate container 7.5 Replacing a Heating Element viewed from the rear 7.7 Replacing a Frypot 7.6 Replacing Contactor Box Components12. Disconnect the oil return flexlines at the frypot ends 22. Reinstall the drain tube assembly Sediment Particle Oil Flow Up for reverse Down for forward 7.8.2 Replacing the Filter Motor, Filter Pump, and Related Components7-10 7.8.3 Replacing the Filter Transformer or Filter Relay Diagnostic LED Legend 7.9 Interface Board Diagnostic ChartMeter Setting TestRefer to page 2-2 for power requirements 7.10 Wiring Diagram, System7-13 8051421F7-14 7.11 Wiring Diagram, Contactor Box7.12 Components Description of Operation Accessories NAVY SURFACE SHIP ELECTRIC FRYERS CHAPTER 8 PARTS LIST8.2 Cabinetry Handle Grab Rail For handle end use Side, Cabinet Single Left Use 212-8479 for Rt. SideTop Cap Single Top cap for five station fryer shown 106-3036SP8.2.2 Cabinet Bases, Braces, and Associated Parts Upright Assembly, Right Use 106-3829 for singles Upright Assembly, Left Use 106-3828 for singlesChannel, Base Rear Use 106-4901 for singles base assembly 8.2.2 Cabinet Bases, Braces, and Associated Parts cont8.3.1 Drain Tube Sections and Associated Parts 8.3 Drain System Components8.3.1.1 Euro-Look Drain Tube Section and Associated Parts See Page 8-10 for DrainValve Detail EURO-LOOK 8.3.1.1 Euro-Look Drain Tube Section and Associated Parts cont8.3.2 Drain Valve Assembly and Component Parts Page ITEM EURO-LOOK 8.4 Electronics and Wiring Components 8.4.1.1 Single Component Box 8.4.1.2 Multiple Vat Component Boxes 8.4.2.1 Single Contactor Box 8.4.2.2 Multiple Vat Contactor Boxes 8.4.3 Heating Element Assembly and Associated Parts 8.4.3 Heating Element Assembly and Associated Parts cont 8.4.5.1 Contactor Box Wiring Assembly - 12-Pin Full-Vat C-1 Wiring8.4.5.2 Contactor Box Wiring Assemblies - 6-Pin Left Element 8.4.48.4.5.4 Single Contactor Box Wiring Assembly 8.4.5.3 Contactor Box Wiring Assemblies - 9-Pin Right Element8.4.5.5 Main Wiring Harness P/N 106-3467SP 14/17kW or P/N 106-2472SP 22kW8.4.5.7 Component Box Wiring Harness - 15-Pin 8.4.5.6 Single Main Wiring Harness8.4.5.8 Single Component Box Wiring Harness - 15-Pin 8.4.5.9 Single Component Box Wiring Harness - 15-Pin without Filter8.5.1 FPH117/122 Filtration Components 8.5 Filtration System Components8.5.1 FPH117/122 Filtration Components cont 8.5.2 FPH217/317 Multiple Battery Filtration System Components units were configured this wayNOTE Some early production STANDARD 8.5.2 FPH217/317 Multiple Battery Filtration System Components contEURO-LOOK Lid for units built before Feb 04, use8.6 Frypot Assembly and Thermostat Frypot P/N 823-2451SPThermostat P/N 8.7 Oil Return System Components 8.7 Oil Return System Components cont Power Cords 8.8 WIRING CONNECTORS, PIN TERMINALS, AND POWER CORDSConnectors COMPONENTShipping Address 8700 Line Avenue, Shreveport, Louisiana SERVICE HOTLINEFAX Parts Tech Support