XM Satellite Radio R-672 manual Dolby Pro Logic II/Dolby Pro Logic IIx Music Parameters

Page 22

R-672(A) 2007.6.15 10:17 AM 페이지 22

ENGLISH

Continued

2. Press the CURSOR UP(▲)/DOWN(▼) buttons to select the desired parameter.

• Depending on the surround mode, each time these buttons are pressed, the parameter mode changes as follows:

* When listening in Dolby Pro Logic II/Dolby Pro Logic IIx Music mode, you can adjust the various surround parameters for optimum surround effect.

“PANO” “C.WIDTH” “DIMEN”

(Panorama mode) (Center width control) (Dimension control)

* When listening in Dolby Virtual Speaker mode, you can select the speaker layout to be used actually for each Dolby Virtual Speaker mode.

REF WIDE

(Dolby VS Reference mode)

(Dolby VS Wide mode)

*When listening in Dolby Headphone mode, you can select the desired listening mode for each Dolby Headphone mode.

DH 1

DH 2

DH 3

(Dolby Headphone 1 mode)

3. Press the CURSOR LEFT(◀)/RIGHT(▶) buttons to adjust the selected parameter as desired.

■When selecting the “NIGHT” (Night mode)

This function compresses the dynamic range of previously specified parts of the Dolby Digital or DTS sound track (with extremely high volume) to minimize the difference in volume between the specified and non specified parts.

This makes it easy to hear all of the sound track when watching movies at night at low levels. The night mode can be set in 11 steps from 0.0 to 1.0 (default value : 0.0)

■Note: In some Dolby Digital or DTS softwares, the night mode may not be valid.

[Dolby Pro Logic II/Dolby Pro Logic IIx Music Parameters]

■When selecting the “PANO” (Panorama) mode

This mode extends the front stereo image to include the surround speakers for an exciting “wraparound” effect with side wall imaging. Select “OFF” or “ON” (default value : OFF).

■When selecting the “C.WIDTH” (Center width) control

This adjusts the center image so it may be heard only from the center speaker, only from the left/right speakers as a phantom image, or from all three front speakers to varying degrees.

The control can be set it 8 steps from 0 to 7 (default value : 3).

■When selecting the “DIMEN” (Dimension) control

This gradually adjusts the soundfield either towards the front or towards the rear. The control can be set in 7 steps from -3 to +3 (default value : 0).

[Dolby Virtual Speaker Parameters]

■When selecting the “REF” (Dolby Virtual Speaker Reference) mode 2 SP : When using 2 front speakers only.

3 SP : When using 2 front and center speakers.

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents CoverA2007.6.15957AM페이지 Safety Instructions Introduction Read this Before Operating Your UnitContents Connecting Antennas System ConnectionsConnecting Video Components HDMIHigh Definition Multimedia Interface connectionConnecting Audio Components Connecting Digital INS and OUT Connecting External INSDigital input default settings Connecting Speakers Connecting Subwoofer PRE OUTConnecting XM only for North America Surround back speakersSwitched AC Outlets AC Input CordFront Panel Controls Fluorescent DisplayAUX in Jack Setup MIC JackVideo 3 in Jacks Remote Controls Remote Control Operation Range Loading BatteriesOperations When selecting the External in as desiredBefore operation When CD, AUX, Video 1~2 is selected as an input source Operate the selected component for playbackAdjusting the tone bass and treble Surround Sound Dolby Virtual Speaker Dolby Pro Logic IIx surroundDolby Pro Logic II surround Dolby Pro LogicSignal format being input Selectable surround mode Enjoying Surround SoundTo cancel the surround mode for stereo operation 2CH downmix modeDolby Pro Logic II/Dolby Pro Logic IIx Music Parameters Dolby Virtual Speaker ParametersAdjusting each channel level with test tone Dolby Headphone ParametersAdjusting the current channel level Memorizing the adjusted channel levels Recalling the memorized channel levelsAuto presetting Auto tuningManual tuning Listening to Radio BroadcastsTuning to preset stations Manual presettingMemory Backup Function Scanning preset stations in sequenceXM Satellite Radio only for North America Signing up for XM Satellite RadioDirect search Channel searchCategory search Error message and status Presetting channels Preset searchSignal strength display mode Displaying XM informationRecording with Tape Dubbing the audio and video signals separately onto VideoRecording Dubbing from video components onto VideoDigital Audio Recording with MD Recorder Optical Digital OUTOther Functions Operating the sleep timerAdjusting the brightness of the fluorescent display Displaying the operation statusSystem Setup Navigating through the setup menuSetup menu flow English When selecting the AMP Assign Setting the SystemWhen selecting the Subwoofer mode When selecting the Tone When selecting the Cinema EQSetting the Input When selecting the DigitalWhen selecting the Remaster When selecting the Video ModeWhen selecting the Auto Surround When selecting the AV SyncSetting the Speaker Setup When selecting the Auto SetupAbout the first listening position PreparationsEnglish When selecting the Speaker Configuration When setting the speaker size by performing the auto setupWhen setting the distance When selecting the Speaker DistanceWhen selecting the desired unit About the speaker sizeWhen selecting the Speaker Crossover About the crossover frequencyWhen selecting the Room EQ Setting the CH Level Adjusting the current channel levelRecalling the memorized channel levels Setting the Sound Parameter When selecting the Night ModeWhen selecting the C. Width Center width control When selecting the Dolby Plii MusicWhen selecting the Pano Panorama mode When selecting the Dimen Dimension controlWhen selecting the Dolby Headphone When selecting the REF Dolby Virtual Speaker Reference mode When selecting the Dolby Virtual SpeakerWhen selecting the Wide Dolby Virtual Speaker Wide mode Troubleshooting Guide Problem Possible Cause RemedySpecifications Amplifier SectionCoverA2007.6.15957AM페이지
Top Page Image Contents