XM Satellite Radio R-672 manual Connecting Subwoofer PRE OUT, Connecting XM only for North America

Page 9

R-672(A) 2007.6.15 10:17 AM 페이지 9

6. CONNECTING SUBWOOFER PRE OUT

• To emphasize the deep bass sounds, connect a powered subwoofer.

■Note :

• When the power amplifier is assigned to "SB+W" (Surround Back+Subwoofer), no signals are output from the SUBWOOFER PRE OUT jack. (For details, refer to "When selecting the AMP ASSIGN" on page 37.)

7. CONNECTING XM (only for North America)

• Connect the XM terminal to the XM Mini-Tuner system (sold

separately).

 

 

 

 

XM Mini-Tuner system

• Position the XM Mini-Tuner system near a south-facing

 

 

 

 

 

 

 

 

 

window to receive the best signal.

 

 

 

 

 

 

 

 

 

When making connections, also refer to the operating

 

 

 

 

 

 

 

 

 

instructions of the XM Mini-Tuner system.

 

 

 

 

 

 

 

 

 

• For the best reception, check the signal strength of the XM radio

 

 

 

 

 

 

 

 

 

signal with using signal strength display mode, then adjust the

 

 

 

 

 

 

 

 

 

position of the XM Mini-Tuner system until “GOOD” is displayed.

 

 

 

 

 

 

 

 

 

(For details, refer to “Displaying XM information” on page 30.)

 

 

 

 

 

 

 

 

 

 

 

•To listen to XM Satellite Radio, refer to “XM Satellite Radio (only for North America)” on page 28.

8. CONNECTING SPEAKERS

• Be sure to connect speakers firmly and correctly according to the channel (left and right) and the polarity (+ and -). If the connections are faulty, no sound will be heard from the speakers, and if the polarity of the speaker connection is incorrect, the sound will be unnatural and lack bass.

• For installing the speakers, refer to "Speaker placement" on page 10.

• After installing the speakers, first adjust the speaker settings according to your environment and speaker layout. (For details, refer to "SETTING THE SPEAKER SETUP" on page 41.)

■Surround back speakers

• When using only one surround back speaker, you should connect it to SURROUND BACK LEFT channel.

In this case, you can connect a subwoofer without built-in amplifier to the SURROUND BACK RIGHT channel. (For details, refer to “When selecting the AMP ASSIGN” on page 37.)

Caution :

• Be sure to use the speakers with the impedance of 6 ohms or above.

• Do not let the bare speaker wires touch each other or any metal part of this unit. This could damage this unit and/or the speakers.

ENGLISH

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents CoverA2007.6.15957AM페이지 Safety Instructions Read this Before Operating Your Unit IntroductionContents System Connections Connecting AntennasHDMIHigh Definition Multimedia Interface connection Connecting Video ComponentsConnecting Audio Components Connecting External INS Connecting Digital INS and OUTDigital input default settings Connecting XM only for North America Connecting Subwoofer PRE OUTConnecting Speakers Surround back speakersAC Input Cord Switched AC OutletsFluorescent Display Front Panel ControlsSetup MIC Jack AUX in JackVideo 3 in Jacks Remote Controls Loading Batteries Remote Control Operation RangeWhen selecting the External in as desired OperationsBefore operation Operate the selected component for playback When CD, AUX, Video 1~2 is selected as an input sourceAdjusting the tone bass and treble Surround Sound Dolby Pro Logic II surround Dolby Pro Logic IIx surroundDolby Virtual Speaker Dolby Pro LogicEnjoying Surround Sound Signal format being input Selectable surround mode2CH downmix mode To cancel the surround mode for stereo operationDolby Virtual Speaker Parameters Dolby Pro Logic II/Dolby Pro Logic IIx Music ParametersDolby Headphone Parameters Adjusting each channel level with test toneAdjusting the current channel level Recalling the memorized channel levels Memorizing the adjusted channel levelsManual tuning Auto tuningAuto presetting Listening to Radio BroadcastsMemory Backup Function Manual presettingTuning to preset stations Scanning preset stations in sequenceSigning up for XM Satellite Radio XM Satellite Radio only for North AmericaChannel search Direct searchCategory search Signal strength display mode Presetting channels Preset searchError message and status Displaying XM informationRecording Dubbing the audio and video signals separately onto VideoRecording with Tape Dubbing from video components onto VideoOptical Digital OUT Digital Audio Recording with MD RecorderAdjusting the brightness of the fluorescent display Operating the sleep timerOther Functions Displaying the operation statusNavigating through the setup menu System SetupSetup menu flow English Setting the System When selecting the AMP AssignWhen selecting the Subwoofer mode When selecting the Cinema EQ When selecting the ToneWhen selecting the Digital Setting the InputWhen selecting the Auto Surround When selecting the Video ModeWhen selecting the Remaster When selecting the AV SyncWhen selecting the Auto Setup Setting the Speaker SetupPreparations About the first listening positionEnglish When setting the speaker size by performing the auto setup When selecting the Speaker ConfigurationWhen selecting the desired unit When selecting the Speaker DistanceWhen setting the distance About the speaker sizeAbout the crossover frequency When selecting the Speaker CrossoverWhen selecting the Room EQ Adjusting the current channel level Setting the CH LevelRecalling the memorized channel levels When selecting the Night Mode Setting the Sound ParameterWhen selecting the Pano Panorama mode When selecting the Dolby Plii MusicWhen selecting the C. Width Center width control When selecting the Dimen Dimension controlWhen selecting the Dolby Headphone When selecting the Dolby Virtual Speaker When selecting the REF Dolby Virtual Speaker Reference modeWhen selecting the Wide Dolby Virtual Speaker Wide mode Problem Possible Cause Remedy Troubleshooting GuideAmplifier Section SpecificationsCoverA2007.6.15957AM페이지
Top Page Image Contents