XM Satellite Radio R-672 manual English

Page 43

R-672(A) 2007.6.15 10:17 AM 페이지 43

Continued

4. Place the microphone on a flat level at the second main listening position.

•For optimum effectiveness, place the microphone at the second main position within the listening area surrounded by the speakers.

5.Press the CURSOR UP(▲)/DOWN(▼) buttons to select the "CONTINUE", then press the ENTER button.

When performing the auto setup

When the auto setup has been completed

ENGLISH

•Loud test tones are output again successively and then if a series of auto setup procedure has been completed, "COMPLETE" will be displayed.

•To stop the auto setup procedure while performing it, (press the CURSOR UP(▲)/DOWN(▼) buttons to select "CANCEL", then) press the ENTER button.

In such a case that the auto setup procedure is stopped before "COMPLETE", the results of each adjustment may not be memorized.

•If there may be a problem with front speakers or microphone connection, “ERROR” will be displayed. In this case, turn off the power, check the connection and then retry the auto setup procedure.

■Notes :

•It takes several minutes to complete the auto setup.

•Before starting auto setup, be sure not to set the SPEAKER button to off.

•Because the test tones are loud, ensure there no infants or small children in the room.

•For best results, ensure the room is as quiet as possible during the auto setup procedure. If there is too much ambient noise, the results may not be satisfactory.

6.To check the results, press the ENTER button.

•Then the results are memorized and the previous menu is displayed.

•Check the results on each setup menu(SPEAKER CONFIGURATION menu on page 44, SPEAKER DISTANCE menu on page 45, SPEAKER CROSSOVER menu on page 46 and CH LEVEL menu for "CAL" mode on page 48).

•If the results are not satisfactory, you can retry the auto setup procedure or personalize your speaker setup and channel level setup by making the settings manually. (For details, refer to "When selecting the SPEAKER CONFIGURATION" on page 44, "When selecting the SPEAKER DISTANCE" on page 45, "When selecting the SPEAKER CROSSOVER" on page 46, "Adjusting each channel level with test tone" on page 23 and "Adjusting the current channel level" on page 24.)

43

Image 43

Contents CoverA2007.6.15957AM페이지 Safety Instructions Read this Before Operating Your Unit IntroductionContents System Connections Connecting AntennasHDMIHigh Definition Multimedia Interface connection Connecting Video ComponentsConnecting Audio Components Connecting Digital INS and OUT Connecting External INSDigital input default settings Surround back speakers Connecting Subwoofer PRE OUTConnecting XM only for North America Connecting SpeakersAC Input Cord Switched AC OutletsFluorescent Display Front Panel ControlsAUX in Jack Setup MIC JackVideo 3 in Jacks Remote Controls Loading Batteries Remote Control Operation RangeOperations When selecting the External in as desiredBefore operation Operate the selected component for playback When CD, AUX, Video 1~2 is selected as an input sourceAdjusting the tone bass and treble Surround Sound Dolby Pro Logic Dolby Pro Logic IIx surroundDolby Pro Logic II surround Dolby Virtual SpeakerEnjoying Surround Sound Signal format being input Selectable surround mode2CH downmix mode To cancel the surround mode for stereo operationDolby Virtual Speaker Parameters Dolby Pro Logic II/Dolby Pro Logic IIx Music ParametersDolby Headphone Parameters Adjusting each channel level with test toneAdjusting the current channel level Recalling the memorized channel levels Memorizing the adjusted channel levelsListening to Radio Broadcasts Auto tuningManual tuning Auto presettingScanning preset stations in sequence Manual presettingMemory Backup Function Tuning to preset stationsSigning up for XM Satellite Radio XM Satellite Radio only for North AmericaDirect search Channel searchCategory search Displaying XM information Presetting channels Preset searchSignal strength display mode Error message and statusDubbing from video components onto Video Dubbing the audio and video signals separately onto VideoRecording Recording with TapeOptical Digital OUT Digital Audio Recording with MD RecorderDisplaying the operation status Operating the sleep timerAdjusting the brightness of the fluorescent display Other FunctionsNavigating through the setup menu System SetupSetup menu flow English When selecting the AMP Assign Setting the SystemWhen selecting the Subwoofer mode When selecting the Cinema EQ When selecting the ToneWhen selecting the Digital Setting the InputWhen selecting the AV Sync When selecting the Video ModeWhen selecting the Auto Surround When selecting the RemasterWhen selecting the Auto Setup Setting the Speaker SetupPreparations About the first listening positionEnglish When setting the speaker size by performing the auto setup When selecting the Speaker ConfigurationAbout the speaker size When selecting the Speaker DistanceWhen selecting the desired unit When setting the distanceAbout the crossover frequency When selecting the Speaker CrossoverWhen selecting the Room EQ Adjusting the current channel level Setting the CH LevelRecalling the memorized channel levels When selecting the Night Mode Setting the Sound ParameterWhen selecting the Dimen Dimension control When selecting the Dolby Plii MusicWhen selecting the Pano Panorama mode When selecting the C. Width Center width controlWhen selecting the Dolby Headphone When selecting the REF Dolby Virtual Speaker Reference mode When selecting the Dolby Virtual SpeakerWhen selecting the Wide Dolby Virtual Speaker Wide mode Problem Possible Cause Remedy Troubleshooting GuideAmplifier Section SpecificationsCoverA2007.6.15957AM페이지