XM Satellite Radio R-672 manual Introduction, Read this Before Operating Your Unit

Page 3

R-672(A) 2007.6.15 10:17 AM 페이지 3

Introduction

READ THIS BEFORE OPERATING YOUR UNIT

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-

SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

ENGLISH

Caution regarding installation

Note : For heat dispersal, do not install this unit in a confined space such as a bookcase or similar enclosure.

Do not block ventilation openings or stack other equipment on the top.

Note to CATV System Installer :

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

FCC INFORMATION

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Caution : Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FOR YOUR SAFETY

 

 

 

 

Units shipped to the U.S.A and CANADA are designed for operation on 120 V AC only.

 

 

 

 

Safety precaution with use of a polarized AC plug.

 

 

 

 

However, some products may be supplied with a nonpolarized plug.

 

U.S.A

 

 

 

 

120 V

CAUTION : To prevent electric shock, match wide blade of plug to wide slot, fully insert.

 

CANADA

 

 

 

 

 

ATTENTION : Pour éviter chocs électriques, introduire la lame la plus large de la fiche dans la borne

 

 

 

 

 

 

 

 

correspondante de la prise et pousser jusqu’ au fond.

CAUTION

Leave a space around the unit for sufficient ventilation.

Avoid installation in extremely hot or cold locations, or in an area that is exposed to direct sunlight or heating equipment.

Keep the unit free from moisture, water, and dust.

Do not let foreign objects in the unit.

The ventilation should not be impeded by covering the ventilation openings with items, such as newspapers, table-cloths, curtains, etc.

No naked flame sources, such as lighted candles, should be placed on the unit.

Please be care the environmental aspects of battery disposal.

The unit shall not be exposed to dripping or splashing for use.

No objects filled with liquids, such as vases, shall be placed on the unit.

Do not let insecticides, benzene, and thinner come in contact with the set.

Never disassemble or modify the unit in any way.

Notes on the AC power cord and the wall outlet.

The unit is not disconnected from the AC power source(mains) as long as it is connected to the wall outlet, even if the unit has been turned off.

When disconnecting the power cord from the wall outlet, always pull the plug, not the power cord.

Disconnect the plug from the wall outlet when not using the unit for long periods of time.

The wall outlet shall be installed near the unit and shall be easily accessible.

3

Image 3
Contents CoverA2007.6.15957AM페이지 Safety Instructions Read this Before Operating Your Unit IntroductionContents System Connections Connecting AntennasHDMIHigh Definition Multimedia Interface connection Connecting Video ComponentsConnecting Audio Components Connecting External INS Connecting Digital INS and OUTDigital input default settings Surround back speakers Connecting Subwoofer PRE OUTConnecting XM only for North America Connecting SpeakersAC Input Cord Switched AC OutletsFluorescent Display Front Panel ControlsSetup MIC Jack AUX in JackVideo 3 in Jacks Remote Controls Loading Batteries Remote Control Operation RangeWhen selecting the External in as desired OperationsBefore operation Operate the selected component for playback When CD, AUX, Video 1~2 is selected as an input sourceAdjusting the tone bass and treble Surround Sound Dolby Pro Logic Dolby Pro Logic IIx surroundDolby Pro Logic II surround Dolby Virtual SpeakerEnjoying Surround Sound Signal format being input Selectable surround mode2CH downmix mode To cancel the surround mode for stereo operationDolby Virtual Speaker Parameters Dolby Pro Logic II/Dolby Pro Logic IIx Music ParametersDolby Headphone Parameters Adjusting each channel level with test toneAdjusting the current channel level Recalling the memorized channel levels Memorizing the adjusted channel levelsListening to Radio Broadcasts Auto tuningManual tuning Auto presettingScanning preset stations in sequence Manual presettingMemory Backup Function Tuning to preset stationsSigning up for XM Satellite Radio XM Satellite Radio only for North AmericaChannel search Direct searchCategory search Displaying XM information Presetting channels Preset searchSignal strength display mode Error message and statusDubbing from video components onto Video Dubbing the audio and video signals separately onto VideoRecording Recording with TapeOptical Digital OUT Digital Audio Recording with MD RecorderDisplaying the operation status Operating the sleep timerAdjusting the brightness of the fluorescent display Other FunctionsNavigating through the setup menu System SetupSetup menu flow English Setting the System When selecting the AMP AssignWhen selecting the Subwoofer mode When selecting the Cinema EQ When selecting the ToneWhen selecting the Digital Setting the InputWhen selecting the AV Sync When selecting the Video ModeWhen selecting the Auto Surround When selecting the RemasterWhen selecting the Auto Setup Setting the Speaker SetupPreparations About the first listening positionEnglish When setting the speaker size by performing the auto setup When selecting the Speaker ConfigurationAbout the speaker size When selecting the Speaker DistanceWhen selecting the desired unit When setting the distanceAbout the crossover frequency When selecting the Speaker CrossoverWhen selecting the Room EQ Adjusting the current channel level Setting the CH LevelRecalling the memorized channel levels When selecting the Night Mode Setting the Sound ParameterWhen selecting the Dimen Dimension control When selecting the Dolby Plii MusicWhen selecting the Pano Panorama mode When selecting the C. Width Center width controlWhen selecting the Dolby Headphone When selecting the Dolby Virtual Speaker When selecting the REF Dolby Virtual Speaker Reference modeWhen selecting the Wide Dolby Virtual Speaker Wide mode Problem Possible Cause Remedy Troubleshooting GuideAmplifier Section SpecificationsCoverA2007.6.15957AM페이지