XM Satellite Radio R-672 When selecting the Speaker Crossover, About the crossover frequency

Page 46

R-672(A) 2007.6.15 10:17 AM 페이지 46

ENGLISH

Continued

When selecting the SPEAKER CROSSOVER

•When speakers are set to "S" (Small), be sure to set their crossover frequency correctly according to their frequency characteristics.

1. Press the CURSOR UP(▲)/DOWN(▼) buttons to select the “X-OVER”, then press the ENTER button.

2. Press the CURSOR UP(▲)/DOWN(▼) buttons to select the desired speaker.

• Each time CURSOR UP(▲)/DOWN(▼) buttons are pressed, “F” (Front), “C” (Center), “S” (Surround) or “SB” (Surround Back) is selected.

■Note :

• You cannot select the subwoofer and the speakers set to "N" (None).

3. Press the CURSOR LEFT(◀)/RIGHT(▶) buttons to set the crossover frequency as desired.

• You can adjust the crossover frequency within the range of 40 ~ 200 Hz in 10 Hz intervals.

4. Repeat the above steps 2 and 3 until the crossover frequencies are all set as desired.

■About the crossover frequency

•When speakers are set to "S" (Small), low frequencies in those channels that are below the crossover frequency are to output from subwoofer or front speakers which are set to “L” (Large) (when not using a subwoofer).

•Refer to the operating instructions of the speakers to be connected. If the frequency range of your speaker is 100 Hz~20 kHz, the crossover frequency should be set to 100 Hz(or slightly higher).

46

Image 46

Contents CoverA2007.6.15957AM페이지 Safety Instructions Introduction Read this Before Operating Your UnitContents Connecting Antennas System ConnectionsConnecting Video Components HDMIHigh Definition Multimedia Interface connectionConnecting Audio Components Connecting Digital INS and OUT Connecting External INSDigital input default settings Connecting Speakers Connecting Subwoofer PRE OUTConnecting XM only for North America Surround back speakersSwitched AC Outlets AC Input CordFront Panel Controls Fluorescent DisplayAUX in Jack Setup MIC JackVideo 3 in Jacks Remote Controls Remote Control Operation Range Loading BatteriesOperations When selecting the External in as desiredBefore operation When CD, AUX, Video 1~2 is selected as an input source Operate the selected component for playbackAdjusting the tone bass and treble Surround Sound Dolby Virtual Speaker Dolby Pro Logic IIx surroundDolby Pro Logic II surround Dolby Pro LogicSignal format being input Selectable surround mode Enjoying Surround SoundTo cancel the surround mode for stereo operation 2CH downmix modeDolby Pro Logic II/Dolby Pro Logic IIx Music Parameters Dolby Virtual Speaker ParametersAdjusting each channel level with test tone Dolby Headphone ParametersAdjusting the current channel level Memorizing the adjusted channel levels Recalling the memorized channel levelsAuto presetting Auto tuningManual tuning Listening to Radio BroadcastsTuning to preset stations Manual presettingMemory Backup Function Scanning preset stations in sequenceXM Satellite Radio only for North America Signing up for XM Satellite RadioDirect search Channel searchCategory search Error message and status Presetting channels Preset searchSignal strength display mode Displaying XM informationRecording with Tape Dubbing the audio and video signals separately onto VideoRecording Dubbing from video components onto VideoDigital Audio Recording with MD Recorder Optical Digital OUTOther Functions Operating the sleep timerAdjusting the brightness of the fluorescent display Displaying the operation statusSystem Setup Navigating through the setup menuSetup menu flow English When selecting the AMP Assign Setting the SystemWhen selecting the Subwoofer mode When selecting the Tone When selecting the Cinema EQSetting the Input When selecting the DigitalWhen selecting the Remaster When selecting the Video ModeWhen selecting the Auto Surround When selecting the AV SyncSetting the Speaker Setup When selecting the Auto SetupAbout the first listening position PreparationsEnglish When selecting the Speaker Configuration When setting the speaker size by performing the auto setupWhen setting the distance When selecting the Speaker DistanceWhen selecting the desired unit About the speaker sizeWhen selecting the Speaker Crossover About the crossover frequencyWhen selecting the Room EQ Setting the CH Level Adjusting the current channel levelRecalling the memorized channel levels Setting the Sound Parameter When selecting the Night ModeWhen selecting the C. Width Center width control When selecting the Dolby Plii MusicWhen selecting the Pano Panorama mode When selecting the Dimen Dimension controlWhen selecting the Dolby Headphone When selecting the REF Dolby Virtual Speaker Reference mode When selecting the Dolby Virtual SpeakerWhen selecting the Wide Dolby Virtual Speaker Wide mode Troubleshooting Guide Problem Possible Cause RemedySpecifications Amplifier SectionCoverA2007.6.15957AM페이지