XM Satellite Radio R-672 manual Connecting Audio Components

Page 7

R-672(A) 2007.6.15 10:17 AM 페이지 7

Continued

There are three types of video jacks(COMPONENT, S-VIDEO, (composite) VIDEO) for connecting video components. Connect them to the corresponding video jacks according to their capability.

For your reference, the excellence in picture quality is as follows : "COMPONENT” > "S-VIDEO” > "(composite) VIDEO”.

When making COMPONENT VIDEO connections, connect "Y" to "Y", "PB/CB" to "CB" (or "B-Y", "PB") and "PR/CR" to "CR" (or "R-Y", "PR" ).

When recording video program sources through VIDEO 1 OUT jacks, you must use the same type of video jacks that you did connect to video playback components such as DVD player, LD player, etc.

This unit is equipped with a function that up-converts composite video or S-Video signals to component video signals or down-converts S-Video signals to composite video signals and outputs them from the MONITOR OUTs. Because of this, you need not connect all the types of MONITOR OUT jacks to the MONITOR TV.

After connecting the video components, you should set the video mode correctly, referring to the following table. (For details, refer to "When selecting the VIDEO MODE" on page 40.)

Relationship between the video input signal and the video output signal

Video input signals

Video Mode

 

MONITOR OUTs

 

COMPONENT

S-VIDEO

(composite) VIDEO

Setting

COMPONENT

S-VIDEO

(composite) VIDEO

 

 

 

 

 

 

 

 

 

 

“AT”(Auto)

Component

S-Video

Composite video

 

 

 

 

 

 

 

“CPN”(Component)*1

Component

×

×

“SVD”(S-Video)*2

S-Video

S-Video

S-Video

 

 

 

 

 

 

“CPS”(Composite)*2

Composite video

Composite video

Composite video

×

“AT”(Auto)

Component

S-Video

S-Video

 

 

 

 

 

 

 

×

“AT”(Auto)

Component

Composite video

Composite video

 

 

 

 

 

 

 

×

×

“AT”(Auto)

Component

×

×

 

 

 

 

 

 

 

×

“AT”(Auto)

S-Video

S-Video

Composite video

 

 

 

 

 

 

 

×

×

“AT”(Auto)

S-Video

S-Video

S-Video

 

 

 

 

 

 

 

×

×

“AT”(Auto)

Composite video

Composite video

Composite video

 

 

 

 

 

 

 

*1 : Component video signal can be output from the MONITOR COMPONENT OUT jacks only.

*2 : The video signal set in the VIDEO MODE menu can be output from all the types of MONITOR OUT jacks.

3. CONNECTING AUDIO COMPONENTS

• The TAPE IN/OUT jacks can be connected to audio recording equipment such as a tape deck, an MD recorder, etc.

ENGLISH

7

Image 7
Contents CoverA2007.6.15957AM페이지 Safety Instructions Read this Before Operating Your Unit IntroductionContents System Connections Connecting AntennasHDMIHigh Definition Multimedia Interface connection Connecting Video ComponentsConnecting Audio Components Connecting Digital INS and OUT Connecting External INSDigital input default settings Surround back speakers Connecting Subwoofer PRE OUTConnecting XM only for North America Connecting SpeakersAC Input Cord Switched AC OutletsFluorescent Display Front Panel ControlsAUX in Jack Setup MIC JackVideo 3 in Jacks Remote Controls Loading Batteries Remote Control Operation RangeOperations When selecting the External in as desiredBefore operation Operate the selected component for playback When CD, AUX, Video 1~2 is selected as an input sourceAdjusting the tone bass and treble Surround Sound Dolby Pro Logic Dolby Pro Logic IIx surroundDolby Pro Logic II surround Dolby Virtual SpeakerEnjoying Surround Sound Signal format being input Selectable surround mode2CH downmix mode To cancel the surround mode for stereo operationDolby Virtual Speaker Parameters Dolby Pro Logic II/Dolby Pro Logic IIx Music ParametersDolby Headphone Parameters Adjusting each channel level with test toneAdjusting the current channel level Recalling the memorized channel levels Memorizing the adjusted channel levelsListening to Radio Broadcasts Auto tuningManual tuning Auto presettingScanning preset stations in sequence Manual presettingMemory Backup Function Tuning to preset stationsSigning up for XM Satellite Radio XM Satellite Radio only for North AmericaDirect search Channel searchCategory search Displaying XM information Presetting channels Preset searchSignal strength display mode Error message and statusDubbing from video components onto Video Dubbing the audio and video signals separately onto VideoRecording Recording with TapeOptical Digital OUT Digital Audio Recording with MD RecorderDisplaying the operation status Operating the sleep timerAdjusting the brightness of the fluorescent display Other FunctionsNavigating through the setup menu System SetupSetup menu flow English When selecting the AMP Assign Setting the SystemWhen selecting the Subwoofer mode When selecting the Cinema EQ When selecting the ToneWhen selecting the Digital Setting the InputWhen selecting the AV Sync When selecting the Video ModeWhen selecting the Auto Surround When selecting the RemasterWhen selecting the Auto Setup Setting the Speaker SetupPreparations About the first listening positionEnglish When setting the speaker size by performing the auto setup When selecting the Speaker ConfigurationAbout the speaker size When selecting the Speaker DistanceWhen selecting the desired unit When setting the distanceAbout the crossover frequency When selecting the Speaker CrossoverWhen selecting the Room EQ Adjusting the current channel level Setting the CH LevelRecalling the memorized channel levels When selecting the Night Mode Setting the Sound ParameterWhen selecting the Dimen Dimension control When selecting the Dolby Plii MusicWhen selecting the Pano Panorama mode When selecting the C. Width Center width controlWhen selecting the Dolby Headphone When selecting the REF Dolby Virtual Speaker Reference mode When selecting the Dolby Virtual SpeakerWhen selecting the Wide Dolby Virtual Speaker Wide mode Problem Possible Cause Remedy Troubleshooting GuideAmplifier Section SpecificationsCoverA2007.6.15957AM페이지