XM Satellite Radio R-672 manual Connecting External INS, Connecting Digital INS and OUT

Page 8

R-672(A) 2007.6.15 10:17 AM 페이지 8

ENGLISH

4. CONNECTING EXTERNAL INS

• Use these jacks to connect the corresponding outputs of a DVD player or external decoder, etc. that has 6, 7 or 8 channel analog audio outputs

• In case of 6 or 7 channel outputs, do not connect both of the SURROUND BACK L and R inputs or the SURROUND BACK R input of this unit. (For details, refer to the operating instructions of the component to be connected.)

5. CONNECTING DIGITAL INS AND OUT

The OPTICAL and the COAXIAL DIGITAL OUTs of the components that are connected to this unit can be connected to these DIGITAL INs.

A digital input should be connected to the components such

as a CD player, LD player, DVD player, etc. capable of outputting DTS Digital Surround, Dolby Digital or PCM format digital signals, etc.

• If the component with OPTICAL IN jack is connected to the OPTICAL OUT jack of this unit, you can record the high quality sound of CDs, etc. without degradation.

• For details, refer to the operating instructions of the component connected.

• When making the COAXIAL DIGITAL connection, be sure to use a 75 Ω COAXIAL cord, not a conventional AUDIO cord.

• All of the commercially available optical fiber cords cannot be used for the equipment. If there is an optical fiber cord which cannot be connected to your equipment, consult your dealer or nearest service organization.

Note :

Be sure to make either a OPTICAL or a COAXIAL DIGITAL connection on each component. (You don’t need to do both.)

Digital input default settings

If you connect the DIGITAL INs to your components, it is easier to do so following the default settings.

If your DIGITAL connections are different from default settings, your should assign the DIGITAL INs you used with the "When selecting the DIGITAL IN" procedure on page 39.

The default settings are as follows :

OPTICAL IN 1 : VIDEO 1, OPTICAL IN 2 : VIDEO 2, COAXIAL IN 1 : CD, COAXIAL IN 2 : AUX.

8

Image 8
Contents CoverA2007.6.15957AM페이지 Safety Instructions Introduction Read this Before Operating Your UnitContents Connecting Antennas System ConnectionsConnecting Video Components HDMIHigh Definition Multimedia Interface connectionConnecting Audio Components Digital input default settings Connecting External INSConnecting Digital INS and OUT Connecting Subwoofer PRE OUT Connecting XM only for North AmericaConnecting Speakers Surround back speakersSwitched AC Outlets AC Input CordFront Panel Controls Fluorescent DisplayVideo 3 in Jacks Setup MIC JackAUX in Jack Remote Controls Remote Control Operation Range Loading BatteriesBefore operation When selecting the External in as desiredOperations When CD, AUX, Video 1~2 is selected as an input source Operate the selected component for playbackAdjusting the tone bass and treble Surround Sound Dolby Pro Logic IIx surround Dolby Pro Logic II surroundDolby Virtual Speaker Dolby Pro LogicSignal format being input Selectable surround mode Enjoying Surround SoundTo cancel the surround mode for stereo operation 2CH downmix modeDolby Pro Logic II/Dolby Pro Logic IIx Music Parameters Dolby Virtual Speaker ParametersAdjusting each channel level with test tone Dolby Headphone ParametersAdjusting the current channel level Memorizing the adjusted channel levels Recalling the memorized channel levelsAuto tuning Manual tuningAuto presetting Listening to Radio BroadcastsManual presetting Memory Backup FunctionTuning to preset stations Scanning preset stations in sequenceXM Satellite Radio only for North America Signing up for XM Satellite RadioCategory search Channel searchDirect search Presetting channels Preset search Signal strength display modeError message and status Displaying XM informationDubbing the audio and video signals separately onto Video RecordingRecording with Tape Dubbing from video components onto VideoDigital Audio Recording with MD Recorder Optical Digital OUTOperating the sleep timer Adjusting the brightness of the fluorescent displayOther Functions Displaying the operation statusSystem Setup Navigating through the setup menuSetup menu flow English When selecting the Subwoofer mode Setting the SystemWhen selecting the AMP Assign When selecting the Tone When selecting the Cinema EQSetting the Input When selecting the DigitalWhen selecting the Video Mode When selecting the Auto SurroundWhen selecting the Remaster When selecting the AV SyncSetting the Speaker Setup When selecting the Auto SetupAbout the first listening position PreparationsEnglish When selecting the Speaker Configuration When setting the speaker size by performing the auto setupWhen selecting the Speaker Distance When selecting the desired unitWhen setting the distance About the speaker sizeWhen selecting the Speaker Crossover About the crossover frequencyWhen selecting the Room EQ Setting the CH Level Adjusting the current channel levelRecalling the memorized channel levels Setting the Sound Parameter When selecting the Night ModeWhen selecting the Dolby Plii Music When selecting the Pano Panorama modeWhen selecting the C. Width Center width control When selecting the Dimen Dimension controlWhen selecting the Dolby Headphone When selecting the Wide Dolby Virtual Speaker Wide mode When selecting the Dolby Virtual SpeakerWhen selecting the REF Dolby Virtual Speaker Reference mode Troubleshooting Guide Problem Possible Cause RemedySpecifications Amplifier SectionCoverA2007.6.15957AM페이지